Degree of conversion of two dualcured resin cements light-irradiated through zirconia ceramic disks
2
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
PURPOSE. The aim of this Fourier transform infrared (FTIR) spectroscopic study was to measure the degree of conversion (DC) of dual-cured resin cements light-irradiated through zirconia ceramic disks with different thicknesses using various light-curing methods. MATERIALS AND METHODS. Zirconia ceramic disks (KT12) with three different thicknesses (1.0, 2.0, and 4.0 mm) were prepared. The light transmittance of the disks was measured using ultraviolet visible near-infrared spectroscopy. Four different light-curing protocols were used by combining two curing light modes (Elipar TriLight (standard mode) and bluephase G2 (high power mode)) with light-exposure times of 40 and 120 seconds. The DCs of the two dual-cured resin cements (Duo-Link and Panavia F2.0) light-irradiated through the disks was analyzed at three time intervals (3, 7, and 10 minutes) by FTIR spectroscopy. The data was analyzed using repeated measures ANOVA (α=.05).Two-way ANOVA and Tukey post hoc test were used to analyze the 10 minute DC results. RESULTS. The 1.0 mm thick disk exhibited low light transmittance (<25%), and the transmittance decreased considerably with increasing disk thickness. All groups exhibited significantly higher 10 minute DC values than the 3 or 7 minute values (P<.05), but some exceptions were observed in Duo-Link. Two-way ANOVA revealed that the influence of the zirconia disk thickness on the 10 minute DC was dependent on the light-curing methods (P<.001). This finding was still valid even at 4.0 mm thickness, where substantial light attenuation took place. CONCLUSION. The curing of the dual-cured resin cements was affected significantly by the light-curing technique, even though the additional chemical polymerization mechanism worked effectively.
Abstract
PURPOSE. The aim of this Fourier transform infrared (FTIR) spectroscopic study was to measure the degree of conversion (DC) of dual-cured resin cements light-irradiated through zirconia ceramic disks with different thicknesses using various light-curing methods. MATERIALS AND METHODS. Zirconia ceramic disks (KT12) with three different thicknesses (1.0, 2.0, and 4.0 mm) were prepared. The light transmittance of the disks was measured using ultraviolet visible near-infrared spectroscopy. Four different light-curing protocols were used by combining two curing light modes (Elipar TriLight (standard mode) and bluephase G2 (high power mode)) with light-exposure times of 40 and 120 seconds. The DCs of the two dual-cured resin cements (Duo-Link and Panavia F2.0) light-irradiated through the disks was analyzed at three time intervals (3, 7, and 10 minutes) by FTIR spectroscopy. The data was analyzed using repeated measures ANOVA (α=.05).Two-way ANOVA and Tukey post hoc test were used to analyze the 10 minute DC results. RESULTS. The 1.0 mm thick disk exhibited low light transmittance (<25%), and the transmittance decreased considerably with increasing disk thickness. All groups exhibited significantly higher 10 minute DC values than the 3 or 7 minute values (P<.05), but some exceptions were observed in Duo-Link. Two-way ANOVA revealed that the influence of the zirconia disk thickness on the 10 minute DC was dependent on the light-curing methods (P<.001). This finding was still valid even at 4.0 mm thickness, where substantial light attenuation took place. CONCLUSION. The curing of the dual-cured resin cements was affected significantly by the light-curing technique, even though the additional chemical polymerization mechanism worked effectively.
참고문헌 (32)
- Attia A, "Influence of surface conditioning and cleaning methods on resin bonding to zirconia ceramic", Dent Mater, 27, pp.207~213 (2011)
- Matinlinna JP, "Enhanced resin-composite bonding to zirconia framework after pretreatment with selected silane monomers", Dent Mater, 27, pp.273~280 (2011)
- Piconi C, "Zirconia as a ceramic biomaterial", Biomaterials, 20, pp.1~25 (1999)
- Piwowarczyk A, "The shear bond strength between luting cements and zirconia ceramics after two pre-treatments", Oper Dent, 30, pp.382~388 (2005)
- Roediger M, "Prospective evaluation of zirconia posterior fixed partial dentures: fouryear clinical results", Int J Prosthodont, 23, pp.141~148 (2010)
- Blatz MB, "Resin-ceramic bonding: a review of the literature", J Prosthet Dent, 89, pp.268~274 (2003)
- Tanaka R, "Cooperation of phosphate monomer and silica modification on zirconia", J Dent Res, 87, pp.666~670 (2008)
- Vagkopoulou T, "Zirconia in dentistry: Part 1. Discovering the nature of an upcoming bioceramic", Eur J Esthet Dent, 4, pp.130~151 (2009)
- Baldissara P, "Translucency of zirconia copings made with different CAD", CAM systems, 2010, pp.104, 6~12
- El-Mowafy OM, "Influence of composite inlay", onlay thickness on hardening of dual-cured resin cements, 2000, pp.66, 147~
- Kim MJ, "Shear bond strengths of various luting cements to zirconia ceramic: surface chemical aspects", J Dent, 39, pp.795~803 (2011)
- Aguiar TR, "Influence of curing mode and time on degree of conversion of one conventional and two self-adhesive resin cements", Oper Dent, 35, pp.295~299 (2010)
- Yan YL, "Changes in degree of conversion and microhardness of dental resin cements", Oper Dent, 35, pp.203~210 (2010)
- Bayne SC, "Dental biomaterials: where are we and where are we going", J Dent Educ, 69, pp.571~585 (2005)
- Gerth HU, "Chemical analysis and bonding reaction of RelyX Unicem and Bifix composites-a comparative study", Dent Mater, 22, pp.934~941 (2006)
- Ferracane JL, "The effect of resin formulation on the degree of conversion and mechanical properties of dental restorative resins", J Biomed Mater Res, 20, pp.121~131 (1986)
- Vrochari AD, "Curing efficiency of four self-etching, self-adhesive resin cements", Dent Mater, 25, pp.1104~1108 (2009)
- Dias MC, "UV-Vis spectrophotometric analysis and light irradiance through hot-pressed and hot-pressed-veneered glass ceramics", Braz Dent J, 19, pp.197~203 (2008)
- Brodbelt RH, "Translucency of dental porcelains", J Dent Res, 59, pp.70~75 (1980)
- Leonard DL, "Light-emitting diode curing lights, Part II", J Esthet Restor Dent, 15, pp.251~255 (2003)
- Kim YK, "Degree of conversion of dual-cured resin cement light-cured through three fibre posts within human root canals: an ex vivo study", Int Endod J, 42, pp.667~674 (2009)
- Pegoraro TA, "Cements for use in esthetic dentistry", Dent Clin North Am, 51, pp.453~471 (2007)
- Faria-e-Silva AL, "Panavia F: the role of the primer", J Oral Sci, 51, pp.255~259 (2009)
- Van Landuyt KL, "Systematic review of the chemical composition of contemporary dental adhesives", Biomaterials, 28, pp.3757~3785 (2007)
- Kwon TY, "Cure mechanisms in materials for use in esthetic dentistry", J Investig Clin Dent, 3, pp.3~16 (2012)
- Mills RW, "Dental composite depth of cure with halogen and blue light emitting diode technology", Br Dent J, 186, pp.388~391 (1999)
- Rueggeberg FA, "The influence of light exposure on polymerization of dual-cure resin cements", Oper Dent, 18, pp.48~55 (1993)
- Arrais CA, "Effect of sodium sulfinate salts on the polymerization characteristics of dualcured resin cement systems exposed to attenuated light-activation", J Dent, 37, pp.219~227 (2009)
- Pazin MC, "Effects of ceramic thickness and curing unit on light transmission through leucite-reinforced material and polymerization of dual-cured luting agent", J Oral Sci, 50, pp.131~136 (2008)
- Jakubiak J, "Camphorquinone–amines photoinitating systems for the initiation of free radical polymerization", Polymer, 44, pp.5219~5226 (2003)
- Kameyama A, "Spectral characteristics of light-curing units and dental adhesives", J Photopolym Sci Technol, 24, pp.411~416 (2011)
- Miletic V, "Micro-Raman spectroscopic analysis of the degree of conversion of composite resins containing different initiators cured by polywave or monowave LED units", J Dent, 40, pp.106~113 (2012)