Comparison of occlusal contact areas of class I and class II molar relationships at finishing using three-dimensional digital models
2
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Objective: This study compared occlusal contact areas of ideally planned set-up and accomplished final models against the initial in class I and II molar relationships at finishing. Methods: Evaluations were performed for 41 post-orthodontic treatment cases, of which 22 were clinically diagnosed as class I and the remainder were diagnosed as full cusp class II. Class I cases had four first premolars extracted, while class II cases had maxillary first premolars extracted. Occlusal contact areas were measured using a three-dimensional scanner and RapidForm 2004. Independent t-tests were used to validate comparison values between class I and II finishings. Repeated measures analysis of variance was used to compare initial, set up, and final models. Results: Molars from cases in the class I finishing for the set-up model showed significantly greater contact areas than those from class II finishing (p < 0.05). The final model class I finishing showed significantly larger contact areas for the second molars (p < 0.05). The first molars of the class I finishing for the final model showed a tendency to have larger contact areas than those of class II finishing, although the difference was not statistically significant (p = 0.078). Conclusions: In set-up models, posterior occlusal contact was better in class I than in class II finishing. In final models, class I finishing tended to have larger occlusal contact areas than class II finishing. [Korean J Orthod 2015;45(3):113-120]
Abstract
Objective: This study compared occlusal contact areas of ideally planned set-up and accomplished final models against the initial in class I and II molar relationships at finishing. Methods: Evaluations were performed for 41 post-orthodontic treatment cases, of which 22 were clinically diagnosed as class I and the remainder were diagnosed as full cusp class II. Class I cases had four first premolars extracted, while class II cases had maxillary first premolars extracted. Occlusal contact areas were measured using a three-dimensional scanner and RapidForm 2004. Independent t-tests were used to validate comparison values between class I and II finishings. Repeated measures analysis of variance was used to compare initial, set up, and final models. Results: Molars from cases in the class I finishing for the set-up model showed significantly greater contact areas than those from class II finishing (p < 0.05). The final model class I finishing showed significantly larger contact areas for the second molars (p < 0.05). The first molars of the class I finishing for the final model showed a tendency to have larger contact areas than those of class II finishing, although the difference was not statistically significant (p = 0.078). Conclusions: In set-up models, posterior occlusal contact was better in class I than in class II finishing. In final models, class I finishing tended to have larger occlusal contact areas than class II finishing. [Korean J Orthod 2015;45(3):113-120]
참고문헌 (15)
- Liu D, "Reappraisal of Class II molar relationships diagnosed from the lingual side", Clin Orthod Res, 4, pp.97~104 (2001)
- Wheeler RC, "An atlas of tooth form" (1969), WB Saunders
- Casko JS, "Objective grading system for dental casts and panoramic radiographs. American Board of Orthodontics", Am J Orthod Dentofacial Orthop, 114, pp.589~599 (1998)
- Fotis V, "Posttreatment changes of skeletal morphology following treatment aimed at restriction of maxillary growth", Am J Orthod, 88, pp.288~296 (1985)
- 장숙윤, "Differences in molar relationships and occlusal contact areas evaluated from the buccal and lingual aspects using 3-dimensional digital models", 대한치과교정학회지, 42(4), pp.182~189 (2012), 대한치과교정학회[DOI]
- Gibbs CH, "Occlusal forces during chewing and swallowing as measured by sound transmission", J Prosthet Dent, 46, pp.443~449 (1981)
- 윤혜림, "한국인에서의 부정교합 여부와 골격형태, 연령, 성별에 따른 교합력의 비교", 대한치과교정학회지, 40(5), pp.304~313 (2010), 대한치과교정학회
- Yurkstas A, "Measurement of occlusal contact area effective in mastication", Am J Orthod, 35, pp.185~195 (1949)
- Garrido García VC, "Evaluation of occlusal contacts in maximum intercuspation using the T-Scan system", J Oral Rehabil, 24, pp.899~903 (1997)
- Angle EH, "Classification of malocclusion", Dental Cosmos, 41, pp.248~357 (1899)
- Hellman M, "An interpretation of angle's Classification of malocclusion of the teeth supported by the evidence from comparative anatomy and evolution", Dental Cosmos, 62, pp.476~ (1920)
- Jang JM, "A qualitative and quantitative study on occlusal conditions in health volunteers and athletes with normal occlusions", J Adv Prosthodont, 36, pp.302~322 (1998)
- Ehrlich J, "Intercuspal contacts of the natural dentition in centric occlusion", J Prosthet Dent, 45, pp.419~421 (1981)
- Delong R, "Comparing maximum intercuspal contacts of virtual dental patients and mounted dental casts", J Prosthet Dent, 88, pp.622~630 (2002)
- 김재홍, "Accuracy and precision of polyurethane dental arch models fabricated using a three-dimensional subtractive rapid prototyping method with an intraoral scanning technique", 대한치과교정학회지, 44(2), pp.69~76 (2014), 대한치과교정학회