Effect of activation and preactivation on the mechanical behavior and neutral position of stainless steel and beta-titanium T-loops
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Objective: To quantify, for each activation, the effect of preactivations of differing distribution and intensity on the neutral position of T-loops (7-mm height), specifically the horizontal force, moment to force (M/F) ratio, and load to deflection ratio. Methods: A total 100 loops measuring 0.017 × 0.025 inches in cross-section were divided into two groups (n = 50 each) according to composition, either stainless steel or beta-titanium. The two groups were further divided into five subgroups, 10 loops each, corresponding to the five preactivations tested: preactivations with occlusal distribution (0o, 20o, and 40o), gingival distribution (20o), and occlusal-gingival distribution (40o). The loops were subjected to a total activation of 6-mm with 0.5-mm iterations. Statistical analysis was performed using comprised ANOVA and Bonferoni multiple comparison tests, with a significance level of 5%. Results: The location and intensity of preactivation influenced the force intensity. For the M/F ratio, the highest value achieved without preactivation was lower than the height of theloop. Without preactivation, the M/F ratio increased with activation, while the opposite effect was observed with preactivation. The increase in the M/F ratio was greater when the preactivation distribution was partially or fully gingival. Conclusions: Depending on the preactivation distribution, displacement of uprights is higher or lower than the activation, which is a factor to consider in clinical practice. [Korean J Orthod 2015;45(4):198-208]
Abstract
Objective: To quantify, for each activation, the effect of preactivations of differing distribution and intensity on the neutral position of T-loops (7-mm height), specifically the horizontal force, moment to force (M/F) ratio, and load to deflection ratio. Methods: A total 100 loops measuring 0.017 × 0.025 inches in cross-section were divided into two groups (n = 50 each) according to composition, either stainless steel or beta-titanium. The two groups were further divided into five subgroups, 10 loops each, corresponding to the five preactivations tested: preactivations with occlusal distribution (0o, 20o, and 40o), gingival distribution (20o), and occlusal-gingival distribution (40o). The loops were subjected to a total activation of 6-mm with 0.5-mm iterations. Statistical analysis was performed using comprised ANOVA and Bonferoni multiple comparison tests, with a significance level of 5%. Results: The location and intensity of preactivation influenced the force intensity. For the M/F ratio, the highest value achieved without preactivation was lower than the height of theloop. Without preactivation, the M/F ratio increased with activation, while the opposite effect was observed with preactivation. The increase in the M/F ratio was greater when the preactivation distribution was partially or fully gingival. Conclusions: Depending on the preactivation distribution, displacement of uprights is higher or lower than the activation, which is a factor to consider in clinical practice. [Korean J Orthod 2015;45(4):198-208]
참고문헌 (27)
- Weinstein S, "Theoretical mechanics and practical orthodontics", Angle Orthod, 29, pp.177~181 (1959)
- Vaden JL, "Ortodoncia principios generales y técnicas", pp.625~682 (2003), Editorial Médica Panamericana S.A
- Burstone CJ, "Optimizing anterior and canine retraction", Am J Orthod, 70, pp.1~19 (1976)
- Burstone CJ, "The mechanics of the segmented arch techniques", Angle Orthod, 36, pp.99~120 (1966)
- Smith RJ, "Mechanics of tooth movement", Am J Orthod, 85, pp.294~307 (1984)
- Siatkowski RE, "Force system analysis of V-bend sliding mechanics", J Clin Orthod, 28, pp.539~546 (1994)
- Braun S, "The Gable bend revisited", Am J Orthod Dentofacial Orthop, 122, pp.523~527 (2002)
- Siatkowski RE, "Continuous arch wire closing loop design, optimization, and verification. Part II", Am J Orthod Dentofacial Orthop, 112, pp.487~495 (1997)
- Techalertpaisarn P, "Mechanical properties of Opus closing loops, L-loops, and T-loops investigated with finite element analysis", Am J Orthod Dentofacial Orthop, 143, pp.675~683 (2013)
- Chen J, "Effects of T-loop geometry on its forces and moments", Angle Orthod, 70, pp.48~51 (2000)
- Kuhlberg AJ, "T-loop position and anchorage control", Am J Orthod Dentofacial Orthop, 112, pp.12~18 (1997)
- Maia LG, "Photoelastic analysis of forces generated by T-loop springs made with stainless steel or titanium-molybdenum alloy", Am J Orthod Dentofacial Orthop, 140, pp.e123~128 (2011)
- Manhartsberger C, "Space closure in adult patients using the segmented arch technique", Angle Orthod, 59, pp.205~210 (1989)
- Marcotte MR., "Biomecânica em ortodontia", pp.1~21 (2003), Livraria Santos Editora
- Shimizu RH, "Desempenho biomecânico da alça “T”, construída com fio de aço inoxidável, durante o fechamento de espaços no tratamento ortodôntico", R Dental Press Ortodon Ortop Facial, 7, pp.49~61 (2002)
- Souza RS, "Avaliação do sistema de forças gerado pela alça T de retração pré-ativada segundo o padrão UNESP-Araraquara", R Dental Press Ortodon Ortop Facial, 8, pp.113~122 (2003)
- Siatkowski RE, "Continuous arch wire closing loop design, optimization, and verification. Part I", Am J Orthod Dentofacial Orthop, 112, pp.393~402 (1997)
- Thiesen G, "Determination of the force systems produced by different configurations of tear drop orthodontic loops", Dental Press J Orthod, 18, pp.19~ (2013)
- Braun S, "On the management of extraction sites", Am J Orthod Dentofacial Orthop, 112, pp.645~655 (1997)
- Halazonetis DJ, "Understanding orthodontic loop preactivation", Am J Orthod Dentofacial Orthop, 113, pp.237~241 (1998)
- Viecilli RF, "Self-corrective T-loop design for differential space closure", Am J Orthod Dentofacial Orthop, 129, pp.48~53 (2006)
- Rose D, "Moment-toforce characteristics of preactivated nickel-titanium and titanium-molybdenum alloy symmetrical T-loops", Am J Orthod Dentofacial Orthop, 135, pp.757~763 (2009)
- Caldas SG, "Force system evaluation of symmetrical betatitanium T-loop springs preactivated by curvature and concentrated bends", Am J Orthod Dentofacial Orthop, 140, pp.e53~58 (2011)
- Ferreira Mdo A, "Experimental force definition system for a new orthodontic retraction spring", Angle Orthod, 75, pp.368~377 (2005)
- Burstone CJ, "Force systems from an ideal arch", Am J Orthod, 65, pp.270~289 (1974)
- Ingram SB Jr, "Comparative range of orthodontic wires", Am J Orthod Dentofacial Orthop, 90, pp.296~307 (1986)
- Odegaard J, "The effects of loops on the torsional stiffnesses of rectangular wires:an in vitro study", Am J Orthod Dentofacial Orthop, 109, pp.496~505 (1996)