Comparison of transition temperature range and phase transformation behavior of nickel-titanium wires
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
Objective: The aim of this research was to evaluate the mechanical properties (MP) and degree of the phase transformation (PT) of martensitic (M-NiTi), austenitic (A-NiTi) and thermodynamic nickel-titanium wire (T-NiTi). Methods: The samples consisted of 0.016 × 0.022 inch M-NiTi (Nitinol Classic, NC), A-NiTi (Optimalloy, OPTI) and T-NiTi (Neo-Sentalloy, NEO). Differential scanning calorimetry (DSC), three-point bending test, X-ray diffraction (XRD), and microstructure examination were used. Statistical evaluation was undertaken using ANOVA test. Results: In DSC analysis, OPTI and NEO showed two peaks in the heating curves and one peak in the cooling curves. However, NC revealed one single broad and weak peak in the heating and cooling curves. Austenite finishing (Af) temperatures were 19.7oC for OPTI, 24.6oC for NEO and 52.4oC for NC. In the three-point bending test, residual deflection was observed for NC, OPTI and NEO. The load ranges of NC and OPTI were broader and higher than NEO. XRD and microstructure analyses showed that OPTI and NEO had a mixture of martensite and austenite at temperatures below Martensite finishing (Mf). NEO and OPTI showed improved MP and PT behavior than NC. Conclusions: The mechanical and thermal behaviors of NiTi wire cannot be completely explained by the expected degree of PT because of complicated martensite variants and independent PT induced by heat and stress. (Korean J Orthod 2010;40(1):40-49)
Abstract
Objective: The aim of this research was to evaluate the mechanical properties (MP) and degree of the phase transformation (PT) of martensitic (M-NiTi), austenitic (A-NiTi) and thermodynamic nickel-titanium wire (T-NiTi). Methods: The samples consisted of 0.016 × 0.022 inch M-NiTi (Nitinol Classic, NC), A-NiTi (Optimalloy, OPTI) and T-NiTi (Neo-Sentalloy, NEO). Differential scanning calorimetry (DSC), three-point bending test, X-ray diffraction (XRD), and microstructure examination were used. Statistical evaluation was undertaken using ANOVA test. Results: In DSC analysis, OPTI and NEO showed two peaks in the heating curves and one peak in the cooling curves. However, NC revealed one single broad and weak peak in the heating and cooling curves. Austenite finishing (Af) temperatures were 19.7oC for OPTI, 24.6oC for NEO and 52.4oC for NC. In the three-point bending test, residual deflection was observed for NC, OPTI and NEO. The load ranges of NC and OPTI were broader and higher than NEO. XRD and microstructure analyses showed that OPTI and NEO had a mixture of martensite and austenite at temperatures below Martensite finishing (Mf). NEO and OPTI showed improved MP and PT behavior than NC. Conclusions: The mechanical and thermal behaviors of NiTi wire cannot be completely explained by the expected degree of PT because of complicated martensite variants and independent PT induced by heat and stress. (Korean J Orthod 2010;40(1):40-49)
참고문헌 (34)
- Sakima MT, "How does temperature influence the properties of rectangular nickel-titanium wires?", Eur J Orthod, 28, pp.282~91 (2006)
- "1998", 212
- Khier SE, "Bending properties of superelastic and nonsuperelastic nickel-titanium orthodontic wires", Am J Orthod Dentofacial Orthop, 99, pp.310~8 (1991)
- Ren CC, "Phase transformation analysis of varied nickel-titanium orthodontic wires", Chin Med J (Engl), 121, pp.2060~4 (2008)
- Meling TR, "The effect of temperature on the elastic responses to longitudinal torsion of rectangular nickel titanium archwires", Angle Orthod, 68, pp.357~68 (1998)
- Meling TR, "The effect of short-term temperature changes on the mechanical properties of rectangular nickel titanium archwires tested in torsion", Angle Orthod, 68, pp.369~76 (1998)
- Kusy RP, "Dynamic mechanical properties of straight titanium alloy arch wires", Dent Mater, 6, pp.228~36 (1990)
- Santoro M, "Nickel-titanium alloys: stress-related temperature transitional range", Am J Orthod Dentofacial Orthop, 118, pp.685~92 (2000)
- Brantley WA, "Temperature-modulated DSC provides new insight about nickel-titanium wire transformations", Am J Orthod Dentofacial Orthop, 124, pp.387~94 (2003)
- Iijima M, "Mechanical behavior at different temperatures and stresses for superelastic nickel-titanium orthodontic wires having different transformation temperatures", Dent Mater, 18, pp.88~93 (2002)
- Bradley TG, "Differential scanning calorimetry (DSC) analyses of superelastic and nonsuperelastic nickel-titanium orthodontic wires", Am J Orthod Dentofacial Orthop, 109, pp.589~97 (1996)
- Burstone CJ, "Chinese NiTi wire - a new orthodontic alloy", Am J Orthod, 87, pp.445~52 (1985)
- Miura F, "The super-elastic property of the Japanese NiTi alloy wire for use in orthodontics", Am J Orthod Dentofacial Orthop, 90, pp.1~10 (1986)
- Brantley WA, "Microstructuralstudies of 35 degrees C copper Ni-Ti orthodontic wire and TEM confirmation of low-temperature martensite transformation", Dent Mater, 24, pp.204~10 (2008)
- Iijima M, "Micro X-ray diffraction study of superelastic nickel-titanium orthodontic wires at different temperatures and stresses", Biomaterials, 23, pp.1769~74 (2002)
- Thayer TA, "X-ray diffraction of nitinol orthodontic arch wires", Am J Orthod Dentofacial Orthop, 107, pp.604~12 (1995)
- Brantley WA, "Temperature-modulated DSC provides new insight about nickel-titanium wires transformations", Am J Orthod Dentofacial Orthop, 124, pp.387~94 (2003)
- Barwart O, "An evaluation of the transition temperature range of superelastic orthodontic NiTi springs using differential scanning calorimetry", Eur J Orthod, 21, pp.497~502 (1999)
- Rondelli G, "Evaluation by electrochemical tests of the passive film stability of equiatomic Ni-Ti alloy also in presence of stress-induced martensite", J Biomed Mater Res, 51, pp.47~54 (2000)
- Airoldi G, "Innovative materials: the NiTi alloys in orthodontics", Biomed Mater Eng, 6, pp.299~305 (1996)
- Airoldi G, "Garattini G. Oral environment temperature changes induced by cold", hot liquid intake, 1997, pp.112, 58~63
- Volchansky A, "Variations in oral temperature", J Oral Rehabil, 21, pp.605~11 (1994)
- Moore R J, "Intra-oral temperature variation over 24 hours", Eur J Orthod, 21, pp.249~61 (1999)
- Dalstra M, "Does the transition temperature of Cu-NiTi archwires affect the amount of tooth movement during alignment?", Orthod Craniofac Res, 7, pp.21~5 (2004)
- Yoneyama T, "Bending properties and transformation temperatures of heat- treated Ni-Ti alloy wire for orthodontic appliances", J Biomed Mater Res, 27, pp.399~402 (1993)
- Tonner RI, "The characteristics of super-elastic Ni-Ti wires in three-point bending. Part I: the effect of temperature", Eur J Orthod, 16, pp.409~19 (1994)
- Bishara SE, "Comparisons of the thermodynamic properties of three nickel-titanium orthodontic archwires", Angle Orthod, 65, pp.117~22 (1995)
- Filleul MP, "properties of Ni-Ti and copper Ni-Ti wires: the effect of temperature on physical properties", Eur J Orthod, 19, pp.637~46 (1997)
- Oltjen JM, "Stiffness-deflection behavior of selected orthodontic wires", Angle Orthod, 67, pp.209~18 (1997)
- Nakano H, "Mechanical properties of several nickel-titanium alloy wires in three-point bending tests", Am J Orthod Dentofacial Orthop, 115, pp.390~5 (1999)
- Gurgel JA, "Force-deflection properties of superelastic nickel-titanium archwires", Am J Orthod Dentofacial Orthop, (120), pp.378~82 (2001)
- Wilkinson PD, "Load-deflection characteristics of superelastic nickel-titanium orthodontic wires", Am J Orthod Dentofacial Orthop, 121, pp.483~95 (2002)
- Fischer-Brandies H, "Transformation behavior, chemical composition, surface topography and bending properties of five selected 0.016 × 0.022 NiTi archwires", J Orofac Orthop, 64, pp.88~99 (2003)
- Parvizi F, "The load", deflection characteristics of thermally activated orthodontic archwires, 2003, pp.25, 417~21