Evaluation of digital dental models obtained from dental cone-beam computed tomography scan of alginate impressions
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Objective: To investigate the dimensional accuracy of digital dental models obtained from the dental cone-beam computed tomography (CBCT) scan of alginate impressions according to the time elapse when the impressions are stored under ambient conditions. Methods: Alginate impressions were obtained from 20 adults using 3 different alginate materials, 2 traditional alginate materials (Alginoplast and Cavex Impressional) and 1 extended-pour alginate material (Cavex ColorChange). The impressions were stored under ambient conditions, and scanned by CBCT immediately after the impressions were taken, and then at 1 hour intervals for 6 hours. After reconstructing three-dimensional digital dental models, the models were measured and the data were analyzed to determine dimensional changes according to the elapsed time. The changes within the measurement error were regarded as clinically acceptable in this study. Results: All measurements showed a decreasing tendency with an increase in the elapsed time after the impressions. Although the extended-pour alginate exhibited a less decreasing tendency than the other 2 materials, there were no statistically significant differences between the materials. Changes above the measurement error occurred between the time points of 3 and 4 hours after the impressions. Conclusions: The results of this study indicate that digital dental models can be obtained simply from a CBCT scan of alginate impressions without sending them to a remote laboratory. However, when the impressions are not stored under special conditions, they should be scanned immediately, or at least within 2 to 3 hours after the impressions are taken.[Korean J Orthod 2016;46(3):129-136]
Abstract
Objective: To investigate the dimensional accuracy of digital dental models obtained from the dental cone-beam computed tomography (CBCT) scan of alginate impressions according to the time elapse when the impressions are stored under ambient conditions. Methods: Alginate impressions were obtained from 20 adults using 3 different alginate materials, 2 traditional alginate materials (Alginoplast and Cavex Impressional) and 1 extended-pour alginate material (Cavex ColorChange). The impressions were stored under ambient conditions, and scanned by CBCT immediately after the impressions were taken, and then at 1 hour intervals for 6 hours. After reconstructing three-dimensional digital dental models, the models were measured and the data were analyzed to determine dimensional changes according to the elapsed time. The changes within the measurement error were regarded as clinically acceptable in this study. Results: All measurements showed a decreasing tendency with an increase in the elapsed time after the impressions. Although the extended-pour alginate exhibited a less decreasing tendency than the other 2 materials, there were no statistically significant differences between the materials. Changes above the measurement error occurred between the time points of 3 and 4 hours after the impressions. Conclusions: The results of this study indicate that digital dental models can be obtained simply from a CBCT scan of alginate impressions without sending them to a remote laboratory. However, when the impressions are not stored under special conditions, they should be scanned immediately, or at least within 2 to 3 hours after the impressions are taken.[Korean J Orthod 2016;46(3):129-136]
참고문헌 (17)
- Fleming PS, "Orthodontic measurements on digital study models compared with plaster models: a systematic review", Orthod Craniofac Res, 14, pp.1~16 (2011)
- Naidu D, "Validity, reliability and reproducibility of three methods used to measure tooth widths for bolton analyses", Aust Orthod J, 25, pp.97~103 (2009)
- White AJ, "Analysis of intra-arch and interarch measurements from digital models with 2 impression materials and a modeling process based on cone-beam computed tomography", Am J Orthod Dentofacial Orthop, 137, pp.456.e1~456.e9 (2010)
- Wiranto MG, "Validity, reliability, and reproducibility of linear measurements on digital models obtained from intraoral and cone-beam computed tomography scans of alginate impressions", Am J Orthod Dentofacial Orthop, 143, pp.140~147 (2013)
- Naidu D, "Validity, reliability, and reproducibility of the iOC intraoral scanner: a comparison of tooth widths and Bolton ratios", Am J Orthod Dentofacial Orthop, 144, pp.304~310 (2013)
- Bailey E, "Predicting tooth-size discrepancy: A new formula utilizing revised landmarks and 3-dimensional laser scanning technology", Am J Orthod Dentofacial Orthop, 143, pp.574~585 (2013)
- Hayashi K, "Assessment of the accuracy and reliability of new 3-dimensional scanning devices", Am J Orthod Dentofacial Orthop, 144, pp.619~625 (2013)
- Grünheid T, "Clinical use of a direct chairside oral scanner: an assessment of accuracy, time, and patient acceptance", Am J Orthod Dentofacial Orthop, 146, pp.673~682 (2014)
- Flügge TV, "Precision of intraoral digital dental impressions with iTero and extraoral digitization with the iTero and a model scanner", Am J Orthod Dentofacial Orthop, 144, pp.471~478 (2013)
- Patzelt SB, "The time efficiency of intraoral scanners: an in vitro comparative study", J Am Dent Assoc, 145, pp.542~551 (2014)
- Torassian G, "Digital models vs plaster models using alginate and alginate substitute materials", Angle Orthod, 80, pp.662~669 (2010)
- Dahlberg G, "Statistical methods for medical and biological students" (1940), George Allen & Unwin
- Rheude B, "An evaluation of the use of digital study models in orthodontic diagnosis and treatment planning", Angle Orthod, 75, pp.300~304 (2005)
- Alcan T, "The relationship between digital model accuracy and time-dependent deformation of alginate impressions", Angle Orthod, 79, pp.30~36 (2009)
- Erbe C, "Dimensional stability of contemporary irreversible hydrocolloids: humidor versus wet tissue storage", J Prosthet Dent, 108, pp.114~122 (2012)
- Walker MP, "Dimensional change over time of extendedstorage alginate impression materials", Angle Orthod, 80, pp.1110~1115 (2010)
- Todd JA, "Dimensional changes of extended-pour alginate impression materials", Am J Orthod Dentofacial Orthop, 143(4 Suppl), pp.S55~S63 (2013)