알지네이트 인상체에서 제작된 치과용 석고 모형의 정확도에 대한 삼차원 디지털 분석
Three dimensional accuracy analysis of dental stone casts fabricated using irreversible hydrocolloid impressions
2
조회
0
다운로드
5
인용
0
참고문헌
키워드
초록
목적: 보관 조건과 석고 주입 시간에 따라 알지네이트 인상체로부터 제작된 모형의 정확성을 알아보고자 하였다. 연구 재료 및 방법: 채득된 알지네이트 인상체는 습도가 유지되는 항습조에 보관하는 것과 진료실 내의 공기 중에 노출되는 상태로 보관 조건을 달리하였다. 보관 조건에 따라 각각 즉시, 채득된 후 10분, 30분, 180분, 360분으로 나누어 보관한 후에 석고 모형을 제작하였다. 제작된 석고 모형을 3D 레이저 스캐너로 삼차원 디지털 모형을 구성하였고 구성된 디지털 모형의 참고점에서 거리를 측정하여 변형률을 비교하였다. 또한 각 실험군의 삼차원 디지털 평균 모형을 제작한 후 중첩을 시행함으로써 표면 변위가 발생한 부위와 크기를 확인하였다. 결과: 인상 채득 즉시 제작한 모형의 변형률이 가장 작게 나타났고, 공기 중에 보관한 인상체보다 항습조에 보관한 인상체의 변형률이 작게 나타났다. 석고 주입 시간이 증가함에 따라서 변형률도 증가하였으며, 석고 주입 시간이 180분을 지나면 보관 조건에 관계없이 대구치 부위에서 변형률과 표면 변위가 증가한다. 결론: 알지네이트 인상체로부터 제작된 모형의 정확성을 위해서는 인상 채득 후, 즉시 모형을 제작해야 한다. 보관이 필요한 경우에는 100% 상대습도가 유지되는 항습조를 이용하고, 보관 시간은 180분을 넘지 않도록 해야 정확한 모형을 얻을 수 있다.
Abstract
Purpose: The objects of this study was to evaluate the accuracy of the dental stone casts made from alginate impressions according to storage condition and stone pouring time. Materials and Methods: Each of upper and lower impressions of dental model was taken. The dental stone models were made immediately, 10, 30, 60, 180, 360 minutes after the impressions were taken at each storage condition. 3D models were constructed by scanning the stone model using 3D laser scanner. With Reference points, positioned on digital models, linear measurements of the dimensional change were compared by 3D metrology software, 3D average models were made and superimposition to identify the specific site of dimensional change and to measure surface deviation (mm). Results: Dental stone models which were made immediately after taking the impression showed the smallest linear dimensional change. As the stone pouring time was prolonged, the linear dimensional change was increased. More than 180 minutes after impression taking, linear dimensional change and surface distortion increased in the posterior molar region, regardless of the storage condition. Conclusion: For the optimum accuracy of the dental stone casts, alginate impression should be poured as soon as possible. If there were a need for storing, a humidor with 100% relative humidity must be used and be stored less than 180 minutes to fabricate the accurate dental model.
참고문헌 (26)
- Anusavice KJ, "Phillips’ science of dental materials", pp.171~176 (2013), Elsevier Inc
- Rubel BS, "mpression materials: a comparative review of impression materials most commonly used in restorative dentistry", Dent Clin North Am, 51, pp.629~642 (2007)
- Donovan TE, "A review of contemporary impression materials and techniques", Dent Clin North Am, 48, pp.445~470 (2004)
- Nandini VV, "Alginate impressions : a practical perspective", J Conserv Dent, 11, pp.37~41 (2008)
- Cook W., "Alginate dental impression materials:chemistry, structure, and properties", J Biomed Mater Res, 20, pp.1~24 (1986)
- Sedda M, "Effect of storage time on the accuracy of casts made from different irreversible hydrocolloids", J Contemp Dent Pract, 9, pp.59~66 (2008)
- Rudd KD, "Accurate casts", J Prosthet Dent, 21, pp.545~554 (1969)
- Eissmann HF, "Dental laboratory procedures: fixed partial dentures. Vol. 2", pp.1~29 (1980), Mosby
- Erbe C, "Dimensional stability of contemporary irreversible hydrocolloids : humidor versus wet tissue storage", J Prosthet Dent, 108, pp.114~122 (2012)
- Walker MP, "Dimensional change over time of extended-storage alginate impression materials", Angle Orthod, 80, pp.1110~1115 (2010)
- Nassar U, "Dimensional stability of irreversible hydrocolloid impression materials as a function of pouring time : a systematic review", J Prosthet Dent, 106, pp.126~133 (2011)
- Johnson GH, "Accuracy of four types of rubber impression materials compared with time of pour and a repeat pour of models", J Prosthet Dent, 53, pp.484~490 (1985)
- Wadhwa SS, "The effect of pouring time on the dimensional accuracy of casts made from different irreversible hydrocolloid impression materials", Contemp Clin Dent, 4, pp.313~318 (2013)
- Cohen BI, "Dimensional accuracy of three different alginate impression materials", J Prosthodont, 4, pp.195~199 (1995)
- 오남식, "아가-알지네이트 연합 인상체의 보관방법 및 idophor 침적소독에 의한 체적 변화에 관한 연구", 대한치과보철학회지, 42(1), pp.21~29 (2004), 대한치과보철학회
- Alcan T, "The relationship between digital model accuracy and time-dependent deformation of alginate impressions", Angle Orthod, 79, pp.30~36 (2009)
- Sousa MV, "Accuracy and reproducibility of 3-dimensional digital model measurements", Am J Orthod Dentofacial Orthop, 142, pp.269~273 (2012)
- Roesnstiel SF, "Contemporary fixed prosthodontics" (2006), Mosby
- Dreesen K, "The influence of mixing methods and disinfectant on the physical properties of alginate impression materials", Eur J Orthod, 35, pp.381~387 (2013)
- Frank RP, "The influence of tray type and other variables on the palatal depth of casts made from irreversible hydrocolloid impressions", J Prosthet Dent, 87, pp.15~22 (2002)
- Ashley M, "Making a good impression: (a 'how to' paper on dental alginate)", Dent Update, 32, pp.169~170 (2005)
- Sakaguchi RL, "Craig’s restorative dental materials" (2012), Elsevier Inc
- Song KY, "A study on dimensional stability of impression materials following immersion disinfection", J Korean Acad Prosthodont, 37, pp.506~515 (1999)
- Nassar U, "Dimensional accuracy of 2 irreversible hydrocolloid alternative impression materials with immediate and delayed pouring", J Can Dent Assoc, 78, pp.c2~ (2012)
- Teeter MG, "In vitro quantification of wear in tibial inserts using microcomputed tomography", Clin Orthop Relat Res, 469, pp.107~112 (2011)
- ADA Council on Scientific Affairs, "Infection control recommendations for the dental office and the dental laboratory", J Am Dent Assoc, 127, pp.672~680 (1996)