The influence of various core designs on stress distribution in the veneered zirconia crown: a finite element analysis study
2
조회
0
다운로드
4
인용
0
참고문헌
키워드
초록
PURPOSE. The purpose of this study was to evaluate various core designs on stress distribution within zirconia crowns. MATERIALS AND METHODS. Three-dimensional finite element models, representing mandibular molars, comprising a prepared tooth, cement layer, zirconia core, and veneer porcelain were designed by computer software. The shoulder (1 mm in width) variations in core were incremental increases of 1 mm, 2 mm and 3 mm in proximal and lingual height, and buccal height respectively. To simulate masticatory force, loads of 280 N were applied from three directions (vertical, at a 45˚ angle, and horizontal). To simulate maximum bite force, a load of 700 N was applied vertically to the crowns. Maximum principal stress (MPS) was determined for each model, loading condition, and position. RESULTS. In the maximum bite force simulation test, the MPSs on all crowns observed around the shoulder region and loading points. The compressive stresses were located in the shoulder region of the veneer-zirconia interface and at the occlusal region. In the test simulating masticatory force, the MPS was concentrated around the loading points, and the compressive stresses were located at the 3 mm height lingual shoulder region, when the load was applied horizontally. MPS increased in the shoulder region as the shoulder height increased. CONCLUSION. This study suggested that reinforced shoulder play an essential role in the success of the zirconia restoration, and veneer fracture due to occlusal loading can be prevented by proper core design, such as shoulder.
Abstract
PURPOSE. The purpose of this study was to evaluate various core designs on stress distribution within zirconia crowns. MATERIALS AND METHODS. Three-dimensional finite element models, representing mandibular molars, comprising a prepared tooth, cement layer, zirconia core, and veneer porcelain were designed by computer software. The shoulder (1 mm in width) variations in core were incremental increases of 1 mm, 2 mm and 3 mm in proximal and lingual height, and buccal height respectively. To simulate masticatory force, loads of 280 N were applied from three directions (vertical, at a 45˚ angle, and horizontal). To simulate maximum bite force, a load of 700 N was applied vertically to the crowns. Maximum principal stress (MPS) was determined for each model, loading condition, and position. RESULTS. In the maximum bite force simulation test, the MPSs on all crowns observed around the shoulder region and loading points. The compressive stresses were located in the shoulder region of the veneer-zirconia interface and at the occlusal region. In the test simulating masticatory force, the MPS was concentrated around the loading points, and the compressive stresses were located at the 3 mm height lingual shoulder region, when the load was applied horizontally. MPS increased in the shoulder region as the shoulder height increased. CONCLUSION. This study suggested that reinforced shoulder play an essential role in the success of the zirconia restoration, and veneer fracture due to occlusal loading can be prevented by proper core design, such as shoulder.
참고문헌 (30)
- Premwara Triwatana, "Clinical performance and failures of zirconia-based fixed partial dentures: a review literature", The Journal of Advanced of Prosthodontics, 4(2), pp.76~83 (2012), 대한치과보철학회
- Imanishi A, "3-D Finite element analysis of all-ceramic posterior crowns", J Oral Rehabil, 30, pp.818~822 (2003)
- Fradeani M, "Clinical experience with Empress crowns", Int J Prosthodont, 10, pp.241~247 (1997)
- Fradeani M, "Fiveyear follow-up with Procera all-ceramic crowns", Quintessence Int, 36, pp.105~113 (2005)
- Fradeani M, "An 11-year clinical evaluation of leucite-reinforced glass-ceramic crowns: a retrospective study", Quintessence Int, 33, pp.503~510 (2002)
- Malament KA, "Survival of Dicor glass-ceramic dental restorations over 14 years. Part II: effect of thickness of Dicor material and design of tooth preparation", J Prosthet Dent, 81, pp.662~667 (1999)
- Malament KA, "Survival of Dicor glass-ceramic dental restorations over 16 years. Part III: effect of luting agent and tooth or tooth-substitute core structure", J Prosthet Dent, 86, pp.511~519 (2001)
- Sailer I, "Five-year clinical results of zirconia frameworks for posterior fixed partial dentures", Int J Prosthodont, 20, pp.383~388 (2007)
- Sailer I, "Prospective clinical study of zirconia posterior fixed partial dentures: 3-year follow-up", Quintessence Int, 37, pp.685~693 (2006)
- Sailer I, "Randomized controlled clinical trial of zirconia-ceramic and metal-ceramic posterior fixed dental prostheses: a 3-year follow-up", Int J Prosthodont, 22, pp.553~560 (2009)
- Raigrodski AJ, "The efficacy of posterior three-unit zirconium-oxide-based ceramic fixed partial dental prostheses: a prospective clinical pilot study", J Prosthet Dent, 96, pp.237~244 (2006)
- Molin MK, "Five-year clinical prospective evaluation of zirconia-based Denzir 3-unit FPDs", Int J Prosthodont, 21, pp.223~227 (2008)
- Roediger M, "Prospective evaluation of zirconia posterior fixed partial dentures: fouryear clinical results", Int J Prosthodont, 23, pp.141~148 (2010)
- Schmitt J, "Zirconia posterior fixed partial dentures: a prospective clinical 3-year follow-up", Int J Prosthodont, 22, pp.597~603 (2009)
- Schmitter M, "Clinical performance of extended zirconia frameworks for fixed dental prostheses: two-year results", J Oral Rehabil, 36, pp.610~615 (2009)
- Vult von Steyern P, "All-ceramic fixed partial dentures designed according to the DC-Zirkon technique. A 2-year clinical study", J Oral Rehabil, 32, pp.180~187 (2005)
- Tsumita M, "Clinical evaluation of posterior all-ceramic FPDs (Cercon): a prospective clinical pilot study", J Prosthodont Res, 54, pp.102~105 (2010)
- Wakabayashi N, "Nonlinear finite element analyses: advances and challenges in dental applications", J Dent, 36, pp.463~471 (2008)
- Eraslan O, "Effects of cantilever design and material on stress distribution in fixed partial dentures-a finite element analysis", J Oral Rehabil, 32, pp.273~278 (2005)
- Rafferty BT, "Design features of a three-dimensional molar crown and related maximum principal stress. A finite element model study", Dent Mater, 26, pp.156~163 (2010)
- Ausiello P, "3D-finite element analyses of cusp movements in a human upper premolar, restored with adhesive resin-based composites", J Biomech, 34, pp.1269~1277 (2001)
- Coelho PG, "Effect of proximal wall height on all-ceramic crown core stress distribution: a finite element analysis study", Int J Prosthodont, 22, pp.78~86 (2009)
- Ohlmann B, "Fracture-load values of all-ceramic cantilevered FPDs with different framework designs", Int J Prosthodont, 22, pp.49~52 (2009)
- Ulusoy M, "Fracture resistance of five different metal framework designs for metal-ceramic restorations", Int J Prosthodont, 15, pp.571~574 (2002)
- Rekow ED, "Factorial analysis of variables influencing stress in all-ceramic crowns", Dent Mater, 22, pp.125~132 (2006)
- Silva NR, "Modified Y-TZP core design improves all-ceramic crown reliability", J Dent Res, 90, pp.104~108 (2011)
- Lundgren D, "Occlusal force pattern during chewing and biting in dentitions restored with fixed bridges of cross-arch extension. I. Bilateral end abutments", J Oral Rehabil, 13, pp.57~71 (1986)
- Gibbs CH, "Occlusal forces during chewing and swallowing as measured by sound transmission", J Prosthet Dent, 46, pp.443~449 (1981)
- Magne P, "Rationalization of shape and related stress distribution in posterior teeth: a finite element study using nonlinear contact analysis", Int J Periodontics Restorative Dent, 22, pp.425~433 (2002)
- Morikawa A., "Investigation of occlusal force on lower first molar in function", Kokubyo Gakkai Zasshi, 61, pp.250~274 (1994)