SUS 육각봉 인발성형 시스템의 클램프 가이드 바에 관한 구조해석
Structural Analysis on Clamp Guide Bar of Drawing Process System for SUS Hexagonal Bar
1
조회
0
다운로드
4
인용
0
참고문헌
키워드
초록
In order to remove rust and impurities from surface of raw SUS circular bar, peeling machine is used to make lustrous and clean surface of SUS circular bar. Drawing process system is used to manufacture SUS hexagonal bar. SUS hexagonal bar have been widely used to make hexagonal bolt/nut, adapter and fittings and so on. The purpose of this study is to investigate the stabilities for guide bar of clamp in drawing process system. As the results, the guide bar showed structural stability in cases of below load of 50 Ton and over hook radius of 3.0mm. Further as the thickness of guide bar hooking with jaw was increased, minimum safety factor was decreased.
Abstract
In order to remove rust and impurities from surface of raw SUS circular bar, peeling machine is used to make lustrous and clean surface of SUS circular bar. Drawing process system is used to manufacture SUS hexagonal bar. SUS hexagonal bar have been widely used to make hexagonal bolt/nut, adapter and fittings and so on. The purpose of this study is to investigate the stabilities for guide bar of clamp in drawing process system. As the results, the guide bar showed structural stability in cases of below load of 50 Ton and over hook radius of 3.0mm. Further as the thickness of guide bar hooking with jaw was increased, minimum safety factor was decreased.
참고문헌 (10)
- 허윤영, "필링머신의 롤러 지그 개발에 관한 구조해석", 한국기계기술학회지, 19(2), pp.242~248 (2017), 한국기계기술학회[DOI]
- 허윤영, "필링머신용 SUS 소재의 열전도 해석 연구", 한국기계기술학회지, 19(3), pp.313~319 (2017), 한국기계기술학회[DOI]
- S. K. Lee, "Review on Profile Drawing Process", The Korean Society for Technology of Plasticity, 25(1), pp.67~74 (2016)
- 이상곤, "인발 선재의 잔류응력에 미치는 공정변수의 영향 및 잔류응력 완화", 소성∙가공, 14(8), pp.704~711 (2005), 한국소성∙가공학회
- W. S. Kang, "A Study on the Crater Wear of Carbide Tool in Cutting SUS 304", Journal of the Korean Society for Precision Engineering, 8(1), pp.84~95 (1991)
- 심한섭, "링기어 절삭을 위한 클램프 척의 응력해석", 한국기계가공학회지, 10(3), pp.73~78 (2011), 한국기계가공학회
- 황영은, "차량 배기관용 V-Insert 클램프의 체결 성능 평가", 한국정밀공학회지, 29(2), pp.208~213 (2012), 한국정밀공학회
- 유선중, "패키지 기판 습식 공정용 클램프 이송 장치의 개발", 한국정밀공학회지, 28(2), pp.193~201 (2011), 한국정밀공학회
- 이영식, "SUS 육각봉 인발성형용 가변형 롤유닛에 관한 구조해석 연구", 한국기계기술학회지, 19(6), pp.827~833 (2017), 한국기계기술학회[DOI]
- 이영식, "SUS 육각봉 인발성형 시스템의 몰드 프레임에 관한 구조 안정성 평가", 한국기계기술학회지, 20(3), pp.279~286 (2018), 한국기계기술학회[DOI]