Experimental investigation and optimization of machining parameters during machining of glass fibre reinforced epoxy based composite using desirability function analysis
0
조회
0
다운로드
6
인용
0
참고문헌
키워드
초록
In the recent years, mankind has established that the protection of the environment becomes a vital part in the discovery ofany engineering applications. Several engineering applications in the areas of agriculture, forestry, energy industries, havedeveloped several composite materials in place of other materials for its effectiveness. This work focuses on synthesis of acomposite material and the matrix material used in the research work was epoxy resin. Glass fibres were used as thereinforcement material for the preparation of the hybrid epoxy based composite. The epoxy used in this work is LB011 epoxyresin lapox B_11. The hardener used is Triethylenetetraamine (TETA). The composite laminates are prepared by varying theweight proportion of the glass fibres and tested for its mechanical properties. The composite laminate with high tensile strengthis selected for the investigation of machining properties of the composite laminate. Optimization of machining parameter arecarried out by a novel analysis called Desirability Function Analysis (DFA), which is an optimal tool considered for theproblems with multi objective optimization function.
Abstract
In the recent years, mankind has established that the protection of the environment becomes a vital part in the discovery ofany engineering applications. Several engineering applications in the areas of agriculture, forestry, energy industries, havedeveloped several composite materials in place of other materials for its effectiveness. This work focuses on synthesis of acomposite material and the matrix material used in the research work was epoxy resin. Glass fibres were used as thereinforcement material for the preparation of the hybrid epoxy based composite. The epoxy used in this work is LB011 epoxyresin lapox B_11. The hardener used is Triethylenetetraamine (TETA). The composite laminates are prepared by varying theweight proportion of the glass fibres and tested for its mechanical properties. The composite laminate with high tensile strengthis selected for the investigation of machining properties of the composite laminate. Optimization of machining parameter arecarried out by a novel analysis called Desirability Function Analysis (DFA), which is an optimal tool considered for theproblems with multi objective optimization function.
참고문헌 (24)
- C. Ahilan, , Adv. Prod. Eng. Manag, 5(3), pp.171~180 (2010)
- S. Biswas, , Fibers Polym, 12(1), pp.73~78 (2011)
- A.I. Azmi, , Int. J. Adv. Manuf. Technol, 64(1-4), pp.247~261 (2013)
- P. K. Bajpai, , Mater. Today : Proc, 5(2), pp.8699~8706 (2018)
- C. Elanchezhian, , Mater. Today : Proc, 5(1), pp.1785~1790 (2018)
- N. Naresh, , IOSR J. Mech. Civ. Eng, 6(1), pp.102~111 (2013)
- O. Osita, , Int. J. Eng. Technol, 7, pp.68~77 (2016)
- J.S. Pang, , HBRC J, 10(2), pp.138~144 (2014)
- K. G. Satyanarayana, , J. Mater. Sci, 17, pp.2453~2462 (2018)
- A. Shahzad, "Mechanical and Physical Testing of Biocomposites", pp.215~239 (2019), Fibre-Reinforced Composites and Hybrid Composites
- G. S. Krishnan, , Mater. Res. Express, 7(1), pp.015102~ (2019)
- K. Palanikumar, , Mater. Manuf. Process, 23(8), pp.858~864 (2008)
- O. Osita, , Int. J. Eng. Technol, 7, pp.68~77 (2016)
- Yu-Min Kim, "Evaluation of the electrical and thermal characteristics of Ag", CuO - epoxy composites, 2012, pp.13, 211~214[DOI]
- M. Srinivasan, "Minimization of delamination, surface roughness and thrust force in drilling of Al2O3 ceramic particle filled CFRP composites", Journal of Ceramic Processing Research, 22(3), pp.345~355 (2021), 청정에너지연구소[DOI]
- R. Vinayagamoorthy, "A central composite design based fuzzy logic for optimization of drilling parameters on natural fiber reinforced composite", Journal of Mechanical Science and Technology, 32(5), pp.2011~2020 (2018), 대한기계학회
- M. P. Jenarthanan, , Int. J. Eng. Sci. Technol, 5(4), pp.22~36 (2013)
- Senthil Kumar KM, "Experimental investigation of palm kernel fibre reinforced epoxy based composite", Journal of Ceramic Processing Research, 22(6), pp.731~738 (2021), 청정에너지연구소[DOI]
- T. Tamilanban, "Taguchi GRA optimization of stir casting parameters in Al-SiC composite", Journal of Ceramic Processing Research, 22(6), pp.629~635 (2021), 청정에너지연구소[DOI]
- M. Manoj, "Synthetization and investigation on mechanical characteristics of aluminium alloy 7075 with TiB2 composite", Journal of Ceramic Processing Research, 22(4), pp.475~481 (2021), 청정에너지연구소[DOI]
- R. Srinivasan, "Optimization of friction stir welding process parameters on AA 6063-SiC-B4C hybrid metal matrix composites by genetic algorithm", Journal of Ceramic Processing Research, 22(1), pp.16~24 (2021), 청정에너지연구소[DOI]
- Mukesh Kumar, "Modeling and optimization of material removal rate and surface roughness for Al6010 HMMCs on WEDM using Response Surface Methodology", Journal of Ceramic Processing Research, 23(3), pp.373~382 (2022), 청정에너지연구소[DOI]
- Shivaperumal M, "Parametric optimization in machining of GFRP composite by taguchi grey relational analysis", Journal of Ceramic Processing Research, 23(3), pp.404~408 (2022), 청정에너지연구소[DOI]
- Thirumalai R, "Microstructural analysis and optimization of welding parameters for AA1100 welded plates", Journal of Ceramic Processing Research, 23(2), pp.221~227 (2022), 청정에너지연구소[DOI]