A comparative study of impression methods using stock tray and intraoral scanner in a completely edentulous patient with an atypical arch shape: a case report
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In complete denture fabrication, accurate preliminary impressions are crucial for obtaining an accurate final impression. However, it can be challenging in cases of atypical arch shapes. This case report compares diagnostic casts made with a stock tray and an intraoral scanner (IOS) in a patient with an atypical arch shape. A 58-year-old edentulous male patient with long, narrow, atypical arches was referred to the Oral and Maxillofacial Surgery department for complete denture fabrication. Compared to the diagnostic cast obtained using IOS with adequately captured anatomical parameters, the primary model obtained using a stock tray showed prominent overextended flanges on the labial and buccal sides of the maxillary arch and less prominent overextended flanges in the mandibular arch with pressure spots in the posterior palatal seal area. The custom tray fabricated from such a model required additional adjustment resulting in increased chair time during the final impression procedure.
Abstract
In complete denture fabrication, accurate preliminary impressions are crucial for obtaining an accurate final impression. However, it can be challenging in cases of atypical arch shapes. This case report compares diagnostic casts made with a stock tray and an intraoral scanner (IOS) in a patient with an atypical arch shape. A 58-year-old edentulous male patient with long, narrow, atypical arches was referred to the Oral and Maxillofacial Surgery department for complete denture fabrication. Compared to the diagnostic cast obtained using IOS with adequately captured anatomical parameters, the primary model obtained using a stock tray showed prominent overextended flanges on the labial and buccal sides of the maxillary arch and less prominent overextended flanges in the mandibular arch with pressure spots in the posterior palatal seal area. The custom tray fabricated from such a model required additional adjustment resulting in increased chair time during the final impression procedure.
참고문헌 (12)
- Ender A, "In vivo precision of conventional and digital methods for obtaining quadrant dental impressions", Clin Oral Investig, 20, pp.1495~1504 (2016)
- Skinner EW, "The effect of surface contact in the retention of a denture", J Prosthet Dent, 1, pp.229~235 (1951)
- Patzelt SB, "Assessing the feasibility and accuracy of digitizing edentulous jaws", J Am Dent Assoc, 144, pp.914~920 (2013)
- Mendonça G, "Digital immediate complete denture for a patient with rhabdomyosarcoma : a clinical report", J Prosthodont, 30, pp.196~201 (2021)
- Choi HY, "A morphological study on residual alveolar ridges of edentulous jaws", J Korean Acad Prosthodont, 29, pp.73~89 (1991)
- Chebib N, "Fit and retention of complete denture bases: Part II - conventional impressions versus digital scans: A clinical controlled crossover study", J Prosthet Dent (2022)
- Lo Russo L, "Three-dimensional differences between intraoral scans and conventional impressions of edentulous jaws : A clinical study", J Prosthet Dent, 123, pp.264~268 (2020)
- Chang Y, "Influence of mandibular residual ridge morphology on pressure distribution during impression procedures : a model experiment", Int J Prosthodont, 31, pp.370~374 (2018)
- Masri G, "Evaluation of the adaptation of complete dentures fabricated using intraoral scanning and conventional techniques", J Contemp Dent Pract, 21, pp.1384~1388 (2020)
- Al Hamad KQ, "Trueness of intraoral scanning of edentulous arches : a comparative clinical study", J Prosthodont, 32, pp.26~31 (2023)
- Bosniac P, "Comparison of an indirect impression scanning system and two direct intraoral scanning systems in vivo", Clin Oral Investig, 23, pp.2421~2427 (2019)
- Duncan JP, "A selective-pressure impression technique for the edentulous maxilla", J Prosthet Dent, 92, pp.299~301 (2004)