Development of a prototype simulator for dental education
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Purpose. The purpose of the study was to fabricate a prototype robotic simulator for dental education, to test whether it could simulate mandibular movements, and to assess the possibility of the stimulator responding to stimuli during dental practice. Materials and methods. A virtual simulator model was developed based on segmentation of the hard tissues using cone-beam computed tomography (CBCT) data. The simulator frame was 3D printed using polylactic acid (PLA) material, and dentiforms and silicone face skin were also inserted. Servo actuators were used to control the movements of the simulator, and the simulator’s response to dental stimuli was created by pressure and water level sensors. A water level test was performed to determine the specific threshold of the water level sensor. The mandibular movements and mandibular range of motion of the simulator were tested through computer simulation and the actual model. Results. The prototype robotic simulator consisted of an operational unit, an upper body with an electric device, a head with a temporomandibular joint (TMJ) and dentiforms. The TMJ of the simulator was capable of driving two degrees of freedom, implementing rotational and translational movements. In the water level test, the specific threshold of the water level sensor was 10.35 ml. The mandibular range of motion of the simulator was 50 mm in both computer simulation and the actual model. Conclusion. Although further advancements are still required to improve its efficiency and stability, the upper-body prototype simulator has the potential to be useful in dental practice education.
Abstract
Purpose. The purpose of the study was to fabricate a prototype robotic simulator for dental education, to test whether it could simulate mandibular movements, and to assess the possibility of the stimulator responding to stimuli during dental practice. Materials and methods. A virtual simulator model was developed based on segmentation of the hard tissues using cone-beam computed tomography (CBCT) data. The simulator frame was 3D printed using polylactic acid (PLA) material, and dentiforms and silicone face skin were also inserted. Servo actuators were used to control the movements of the simulator, and the simulator’s response to dental stimuli was created by pressure and water level sensors. A water level test was performed to determine the specific threshold of the water level sensor. The mandibular movements and mandibular range of motion of the simulator were tested through computer simulation and the actual model. Results. The prototype robotic simulator consisted of an operational unit, an upper body with an electric device, a head with a temporomandibular joint (TMJ) and dentiforms. The TMJ of the simulator was capable of driving two degrees of freedom, implementing rotational and translational movements. In the water level test, the specific threshold of the water level sensor was 10.35 ml. The mandibular range of motion of the simulator was 50 mm in both computer simulation and the actual model. Conclusion. Although further advancements are still required to improve its efficiency and stability, the upper-body prototype simulator has the potential to be useful in dental practice education.
참고문헌 (45)
- Sachdeo A, "An analysis of patient grievances in a dental school clinical environment", J Dent Educ, 76, pp.1317~1322 (2012)
- Rad FA, "Rapid transition to distance learning due to COVID-19 : Perceptions of postgraduate dental learners and instructors", PLoS One, 16, pp.e0246584~ (2021)
- Eckles RE, "Medical ethics education: where are we? Where should we be going? a review", Acad Med, 80, pp.1143~1152 (2005)
- Beemsterboer PL, "Developing an ethic of access to care in dentistry", J Dent Educ, 70, pp.1212~1216 (2006)
- Mossey PA, "Scope of the OSCE in the assessment of clinical skills in dentistry", Br Dent J, 190, pp.323~326 (2001)
- Rodrigues P, "Usability, acceptance, and educational usefulness study of a new haptic operative dentistry virtual reality simulator", Comput Methods Programs Biomed, 221, pp.106831~ (2022)
- Murbay S, "‘Evaluation of the introduction of a dental virtual simulator on the performance of undergraduate dental students in the pre-clinical operative dentistry course’", Eur J Dent Educ, 24, pp.5~16 (2020)
- Mirghani I, "Capturing differences in dental training using a virtual reality simulator", Eur J Dent Educ, 22, pp.67~71 (2018)
- de Boer IR, "The effect of variations in force feedback in a virtual reality environment on the performance and satisfaction of dental students", Simul Healthc, 14, pp.169~174 (2019)
- Tanzawa T, "Introduction of a robot patient into dental education", Eur J Dent Educ, 16, pp.e195~e199 (2012)
- Tanzawa T, "Medical emergency education using a robot patient in a dental setting", Eur J Dent Educ, 17, pp.e114~e119 (2013)
- McDevitt WE, "Learning a clinical method to identify a mandibular reference position", Eur J Dent Educ, 2, pp.33~38 (1998)
- McKee JR, "Comparing condylar position repeatability for standardized versus nonstandardized methods of achieving centric relation", J Prosthet Dent, 77, pp.280~284 (1997)
- Peck CC, "The variability of condylar point pathways in open-close jaw movements", J Prosthet Dent, 77, pp.394~404 (1997)
- Celic R, "Relationship of slightly limited mandibular movements to temporomandibular disorders", Braz Dent J, 15, pp.151~154 (2004)
- Mohamed SE, "Articulators in dental education and practice", J Prosthet Dent, 36, pp.319~325 (1976)
- Kurth LE, "Mandibular movement and articulator occlusion", J Am Dent Assoc, 39, pp.37~46 (1949)
- Hugger A, "The rotation vs translation behavior during habitual opening and closing movements of the mandible and the relationship to movement paths of condylar points", Int J Comput Dent, 23, pp.17~26 (2020)
- Abe S, "Educational effects using a robot patient simulation system for development of clinical attitude", Eur J Dent Educ, 22, pp.e327~e336 (2018)
- Ahire M, "Dental health education through the brushing ROBOTUTOR : a new learning experience", J Indian Soc Periodontol, 16, pp.417~420 (2012)
- Newby JP, "Simulation of medical emergencies in dental practice : development and evaluation of an undergraduate training programme", Aust Dent J, 55, pp.399~404 (2010)
- Kinoshita H, "Development of a drilling simulator for dental implant surgery", J Dent Educ, 80, pp.83~90 (2016)
- Nishino T, "Swallowing as a protective reflex for the upper respiratory tract", Anesthesiology, 79, pp.588~601 (1993)
- Kohjitani A, "Accumulated oropharyngeal water increases coughing during dental treatment with intravenous sedation", J Oral Rehabil, 35, pp.203~208 (2008)
- Hanamoto H, "Both head extension and mouth opening impair the ability to swallow in the supine position", J Oral Rehabil, 41, pp.588~594 (2014)
- Cavalcanti BN, "High-speed cavity preparation techniques with different water flows", J Prosthet Dent, 87, pp.158~161 (2002)
- Lauer HC, "Effects of the temperature of cooling water during high-speed and ultrahigh-speed tooth preparation", J Prosthet Dent, 63, pp.407~414 (1990)
- Koster TJ, "Water coolant supply in relation to different ultrasonic scaler systems, tips and coolant settings", J Clin Periodontol, 36, pp.127~131 (2009)
- Matys J, "Dental aerosol as a hazard risk for dental workers", Materials(Basel), 13, pp.5109~ (2020)
- Choi JJE, "Dental high-speed handpiece and ultrasonic scaler aerosol generation levels and the effect of suction and air supply", Infect Control Hosp Epidemiol, 44, pp.926~933 (2023)
- Rolke R, "Quantitative sensory testing : a comprehensive protocol for clinical trials", Eur J Pain, 10, pp.77~88 (2006)
- Corah NL, "The dentist-patient relationship : perceived dentist behaviors that reduce patient anxiety and increase satisfaction", J Am Dent Assoc, 116, pp.73~76 (1988)
- Lee M, "Dentists’ attitudes toward patient-centered care and its predictors : a cross-sectional study in South Korea", BMC Oral Health, 23, pp.75~ (2023)
- Lindauer SJ, "Condylar movement and mandibular rotation during jaw opening", Am J Orthod Dentofacial Orthop, 107, pp.573~577 (1995)
- Messerman T, "A means for studying mandibular movements", J Prosthet Dent, 17, pp.36~43 (1967)
- Posselt U, "Range of movement of the mandible", J Am Dent Assoc, 56, pp.10~13 (1958)
- Posselt U., "Physiology of occlusion and rehabilitation", pp.41~ (1962), Blackwell Scientific
- Li XY, "The normal range of maximum mouth opening and its correlation with height or weight in the young adult Chinese population", J Dent Sci, 12, pp.56~59 (2017)
- Park Y, "An analysis of the temporomandibular joint range of motion and related factors in children and adolescents", Children(Basel), 8, pp.515~ (2021)
- Lewis RP, "Sex differences in mandibular movements during opening and closing", Am J Orthod Dentofacial Orthop, 120, pp.294~303 (2001)
- Al-Dlaigan YH, "Maximum mouth opening in saudi adolescents", J Int Oral Health, 6, pp.45~49 (2014)
- Dario P, "Robotics for medical applications", IEEE Robot Autom Mag, 3, pp.44~56 (1996)
- Locsin RC, "The co-existence of technology and caring in the theory of technological competency as caring in nursing", J Med Invest, 64, pp.160~164 (2017)
- Adel S, "Robotic applications in orthodontics : changing the face of contemporary clinical care", Biomed Res Int, 2021, pp.9954615~ (2021)
- Ahmad P, "Dental robotics : a disruptive technology", Sensors(Basel), 21, pp.3308~ (2021)