Stress distribution of molars restored with minimal invasive and conventional technique: a 3-D finite element analysis
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Purpose: This study aimed to analyze stress distribution and maximum von Mises stress generated in intracoronal restorations and in tooth structures of mandibular molars with various types of cavity designs and materials. Materials and Methods: Threedimensional solid models of mandible molar such as O inlay cavity with composite and gold (OR-C, OG-C), MO inlay cavity with composite and gold (MR-C, MG-C), and minimal invasive cavity on occlusal and proximal surfaces (OR-M, MR-M) were designed. To simulate masticatory force, static axial load with total force of 200 N was applied on the tooth at 10 occlusal contact points. A finite element analysis was performed to predict stress distribution generated by occlusal loading. Results: Restorations with minimal cavity design generated significantly lower values of von Mises stress (OR-M model: 26.8 MPa; MR-M model: 72.7 MPa) compared to those with conventional cavity design (341.9 MPa to 397.2 MPa). In tooth structure, magnitudes of maximum von Mises stresses were similar among models with conventional design (372.8 - 412.9 MPa) and models with minimal cavity design (361.1 - 384.4 MPa). Conclusion: Minimal invasive models generated smaller maximum von Mises stresses within restorations. Within the enamel, similar maximum von Mises stresses were observed for models with minimal cavity design and those with conventional design.
Abstract
Purpose: This study aimed to analyze stress distribution and maximum von Mises stress generated in intracoronal restorations and in tooth structures of mandibular molars with various types of cavity designs and materials. Materials and Methods: Threedimensional solid models of mandible molar such as O inlay cavity with composite and gold (OR-C, OG-C), MO inlay cavity with composite and gold (MR-C, MG-C), and minimal invasive cavity on occlusal and proximal surfaces (OR-M, MR-M) were designed. To simulate masticatory force, static axial load with total force of 200 N was applied on the tooth at 10 occlusal contact points. A finite element analysis was performed to predict stress distribution generated by occlusal loading. Results: Restorations with minimal cavity design generated significantly lower values of von Mises stress (OR-M model: 26.8 MPa; MR-M model: 72.7 MPa) compared to those with conventional cavity design (341.9 MPa to 397.2 MPa). In tooth structure, magnitudes of maximum von Mises stresses were similar among models with conventional design (372.8 - 412.9 MPa) and models with minimal cavity design (361.1 - 384.4 MPa). Conclusion: Minimal invasive models generated smaller maximum von Mises stresses within restorations. Within the enamel, similar maximum von Mises stresses were observed for models with minimal cavity design and those with conventional design.
참고문헌 (28)
- Sabbagh J, "Posterior composites: Update on cavities and filling techniques", J Dent, 57, pp.86~90 (2017)
- Tyas MJ, "Minimal intervention dentistry - a review. FDI Commission Project 1-97", Int Dent J, 50, pp.1~12 (2000)
- Lynch CD, "Guidance on posterior resin composites:Academy of Operative Dentistry - European Section", J Dent, 42, pp.377~383 (2014)
- Banerjee A, "Minimal intervention dentistry: part 7. Minimally invasive operative caries management:rationale and techniques", Br Dent J, 214, pp.107~111 (2013)
- Ericson D, "Minimally Invasive Dentistry - concepts and techniques in cariology", Oral Health Prev Dent, 1, pp.59~72 (2003)
- Tassery H, "Use of new minimum intervention dentistry technologies in caries management", Aust Dent J, 58(Suppl 1), pp.40~59 (2013)
- Casagrande L, "Repair may increase survival of direct posterior restorations - A practice based study", J Dent, 64, pp.30~36 (2017)
- Staehle HJ, "A 6.5-year clinical follow-up of direct resin composite buildups in the posterior dentition: Introduction of a new minimally invasive restorative method", J Dent, 43, pp.1211~1217 (2015)
- White JM, "Rationale and treatment approach in minimally invasive dentistry", J Am Dent Assoc, 131, pp.13S~19S (2000)
- Abu-Hanna AA, "Resin composite reinforcement of undermined enamel", Oper Dent, 29, pp.234~237 (2004)
- Eidelman E, "Composite resin support of undermined enamel in amalgam restorations", Pediatr Dent, 21, pp.118~120 (1999)
- Fonseca RB, "The influence of cavity preparation design on fracture strength and mode of fracture of laboratory processed composite resin restorations", J Prosthet Dent, 98, pp.277~284 (2007)
- 양홍서, "Stress distribution in premolars restored with inlays or onlays: 3D finite element analysis", The Journal of Advanced of Prosthodontics, 10(3), pp.184~190 (2018), 대한치과보철학회[DOI]
- St-Georges AJ, "Fracture resistance of prepared teeth restored with bonded inlay restorations", J Prosthet Dent, 89, pp.551~557 (2003)
- Costa A, "The influence of elastic modulus of inlay materials on stress distribution and fracture of premolars", Oper Dent, 39, pp.E160~E170 (2014)
- Yamanel K, "Effects of different ceramic and composite materials on stress distribution in inlay and onlay cavities: 3-D finite element analysis", Dent Mater J, 28, pp.661~670 (2009)
- Latino C, "Support of undermined occlusal enamel provided by restorative materials", Quintessence Int, 32, pp.287~291 (2001)
- Soares CJ, "Fracture resistance of teeth restored with indirectcomposite and ceramic inlay systems", Quintessence Int, 35, pp.281~286 (2004)
- Dejak B, "Three-dimensional finite element analysis of strength and adhesion of composite resin versus ceramic inlays in molars", J Prosthet Dent, 99, pp.131~140 (2008)
- Jiang W, "Stress distribution in molars restored with inlays or onlays with or without endodontic treatment: a threedimensional finite element analysis", J Prosthet Dent, 103, pp.6~12 (2010)
- Zarone F, "Evaluation of the biomechanical behavior of maxillary central incisors restored by means of endocrowns compared to a natural tooth: a 3D static linear finite elements analysis", Dent Mater, 22, pp.1035~1044 (2006)
- Guven S, "Three-dimensional finite-element analysis of two ceramic inlay restorations with different cavity designs", Biotechnol Biotechnol Equip, 29, pp.579~585 (2015)
- Magne P, "Efficient 3D finite element analysis of dental restorative procedures using micro-CT data", Dent Mater, 23, pp.539~548 (2007)
- 허경회, "Three-dimensional finite element analysis of the splinted implant prosthesis in a reconstructed mandible", The Journal of Advanced of Prosthodontics, 10(2), pp.138~146 (2018), 대한치과보철학회[DOI]
- Zelic K, "Mechanical weakening of devitalized teeth: three-dimensional Finite Element Analysis and prediction of tooth fracture", Int Endod J, 48, pp.850~863 (2015)
- Wayne JS, "Effect of restoration volume on stresses in a mandibular molar: a finite element study", J Prosthet Dent, 112, pp.925~931 (2014)
- Ausiello P, "Numerical fatigue 3D-FE modeling of indirect composite-restored posterior teeth", Dent Mater, 27, pp.423~430 (2011)
- Thompson MC, "The allceramic, inlay supported fixed partial denture. Part 1. Ceramic inlay preparation design: a literature review", Aust Dent J, 55, pp.120~127 (2010)