Influence of heating rate on the flexural strength of monolithic zirconia
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
PURPOSE. Fabrication of zirconia restorations with ideal mechanical properties in a short period is a great challenge for clinicians. The purpose of the study was to investigate the effect of heating rate on the mechanical and microstructural properties of monolithic zirconia. MATERIALS AND METHODS. Forty monolithic zirconia specimens were prepared from presintered monolithic zirconia blanks. All specimens were then assigned to 4 groups according to heating rate as Control, Group 15°C, Group 20°C, and Group 40°C. All groups were sintered according to heating rates with the sintering temperature of 1500°C, a holding time of 90 minutes and natural cooling. The phase composition was examined by XRD analysis, three-point bending test was conducted to examine the flexural strength, and Weibull analysis was conducted to determine weibull modulus and characteristic strength. Average grain sizes were determined by SEM analysis. One-way ANOVA test was performed at a significance level of 0.05. RESULTS. Only tetragonal phase characteristic peaks were determined on the surface of analyzed specimens. Differences among the average grain sizes of the groups were not statistically significant. The results of the three-point bending test revealed no significant differences among the flexural strength of the groups (P>.05). Weibull modulus of groups was ranging from 3.50 to 4.74. The highest and the lowest characteristic strength values were obtained in Group 20°C and Control Group, respectively. CONCLUSION. Heating rate has no significant effect on the flexural strength of monolithic zirconia. Monolithic zirconia restorations can be produced in shorter sintering periods without affecting the flexural strength by modifying the heating rate.
Abstract
PURPOSE. Fabrication of zirconia restorations with ideal mechanical properties in a short period is a great challenge for clinicians. The purpose of the study was to investigate the effect of heating rate on the mechanical and microstructural properties of monolithic zirconia. MATERIALS AND METHODS. Forty monolithic zirconia specimens were prepared from presintered monolithic zirconia blanks. All specimens were then assigned to 4 groups according to heating rate as Control, Group 15°C, Group 20°C, and Group 40°C. All groups were sintered according to heating rates with the sintering temperature of 1500°C, a holding time of 90 minutes and natural cooling. The phase composition was examined by XRD analysis, three-point bending test was conducted to examine the flexural strength, and Weibull analysis was conducted to determine weibull modulus and characteristic strength. Average grain sizes were determined by SEM analysis. One-way ANOVA test was performed at a significance level of 0.05. RESULTS. Only tetragonal phase characteristic peaks were determined on the surface of analyzed specimens. Differences among the average grain sizes of the groups were not statistically significant. The results of the three-point bending test revealed no significant differences among the flexural strength of the groups (P>.05). Weibull modulus of groups was ranging from 3.50 to 4.74. The highest and the lowest characteristic strength values were obtained in Group 20°C and Control Group, respectively. CONCLUSION. Heating rate has no significant effect on the flexural strength of monolithic zirconia. Monolithic zirconia restorations can be produced in shorter sintering periods without affecting the flexural strength by modifying the heating rate.
참고문헌 (30)
- Kim HK, "Effect of the number of coloring liquid applications on the optical properties of monolithic zirconia", Dent Mater, 30, pp.e229~e237 (2014)
- 최유성, "In vitro evaluation of fracture strength of zirconia restoration veneered with various ceramic materials", The Journal of Advanced of Prosthodontics, 4(3), pp.162~169 (2012), 대한치과보철학회[DOI]
- Premwara Triwatana, "Clinical performance and failures of zirconia-based fixed partial dentures: a review literature", The Journal of Advanced of Prosthodontics, 4(2), pp.76~83 (2012), 대한치과보철학회[DOI]
- Stawarczyk B, "The effect of zirconia sintering temperature on flexural strength, grain size, and contrast ratio", Clin Oral Investig, 17, pp.269~274 (2013)
- Lughi V, "Low temperature degradation-aging-of zirconia : A critical review of the relevant aspects in dentistry", Dent Mater, 26, pp.807~820 (2010)
- Piconi C, "Zirconia as a ceramic biomaterial", Biomaterials, 20, pp.1~25 (1999)
- Studart AR, "Fatigue of zirconia under cyclic loading in water and its implications for the design of dental bridges", Dent Mater, 23, pp.106~114 (2007)
- Steffen AA, "Cyclic fatigue life and crack-growth behavior of microstructurally small cracks in magnesia-partially stabilized zirconia ceramics", J Am Ceram Soc, 74, pp.1259~1268 (1991)
- Papia E, "Surface structure and mechanical properties of impaction-modified Y-TZP", Dent Mater, 30, pp.808~816 (2014)
- Guazzato M, "Influence of surface and heat treatments on the flexural strength of Y-TZP dental ceramic", J Dent, 33, pp.9~18 (2005)
- Ersoy NM, "The effects of sintering temperature and duration on the flexural strength and grain size of zirconia", Acta Biomater Odontol Scand, 1, pp.43~50 (2015)
- Kosmac T, "The effect of surface grinding and sandblasting on flexural strength and reliability of Y-TZP zirconia ceramic", Dent Mater, 15, pp.426~433 (1999)
- Swab JJ, "Low temperature degradation of Y-TZP materials", J Mater Sci, 26, pp.6706~6714 (1991)
- Hjerppe J, "Effect of sintering time on biaxial strength of zirconium dioxide", Dent Mater, 25, pp.166~171 (2009)
- Hallmann L, "Effect of dopants and sintering temperature on microstructure and low temperature degradation of dental Y-TZPzirconia", J Eur Ceram Soc, 32, pp.4091~4104 (2012)
- Guess PC, "Zirconia in fixed implant prosthodontics", Clin Implant Dent Relat Res, 14, pp.633~645 (2012)
- Chevalier J, "What future for zirconia as a biomaterial?", Biomaterials, 27, pp.535~543 (2006)
- Kaizer MR, "Speed sintering translucent zirconia for chairside one-visit dental restorations : Optical, mechanical, and wear characteristics", Ceram Int, 43, pp.10999~11005 (2017)
- 김미진, "Effects of the sintering conditions of dental zirconia ceramics on the grain size and translucency", The Journal of Advanced of Prosthodontics, 5(2), pp.161~166 (2013), 대한치과보철학회[DOI]
- Hjerppe J, "Effect of shading the zirconia framework on biaxial strength and surface microhardness", Acta Odontol Scand, 66, pp.262~267 (2008)
- Jiang L, "Effects of sintering temperature and particle size on the translucency of zirconium dioxide dental ceramic", J Mater Sci Mater Med, 22, pp.2429~2435 (2011)
- Ebeid K, "Effect of changes in sintering parameters on monolithic translucent zirconia", Dent Mater, 30, pp.e419~24 (2014)
- "ISO 6872. Dentistry-ceramic materials" (2015)[URL]
- Guazzato M, "Strength, fracture toughness and microstructure of a selection of allceramic materials. Part II. Zirconia-based dental ceramics", Dent Mater, 20, pp.449~456 (2004)
- Stawarczyk B, "Comparison of four monolithic zirconia materials with conventional ones: Contrast ratio, grain size, four-point flexural strength and two-body wear", J Mech Behav Biomed Mater, 59, pp.128~138 (2016)
- Kosmac T, "The effect of surface grinding and sandblasting on flexural strength and reliability of Y-TZP zirconia ceramic", Dent Mater, 15, pp.426~433 (1999)
- Denry I, "State of the art of zirconia for dental applications", Dent Mater, 24, pp.299~307 (2008)
- Gupta TK, "Effect of stress-induced phase transformation on the properties of polycrystalline zirconia containing metastable tetragonal phase", J Mater Sci, 13, pp.1464~1470 (1978)
- Kelly JR, "Stabilized zirconia as a structural ceramic : an overview", Dent Mater, 24, pp.289~298 (2008)
- Bravo-Leon A, "Fracture toughness of nanocrystalline tetragonal zirconia with low yttria content", Acta Mater, 50, pp.4555~4562 (2002)