Assessment of effect of accelerated aging on interim fixed dental materials using digital technologies
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
PURPOSE. This study assessed the physical and mechanical properties of interim crown materials fabricated using various digital techniques after accelerated aging. MATERIALS AND METHODS. Three groups of interim dental restorative materials (N = 20) were tested. The first group (CO) was fabricated using a conventional manual method. The second group (ML) was prepared from prefabricated resin blocks for the milling method and cut into specimensizes using a cutting disc. The third group (3D) was additively manufactured using a digital light-processing (DLP) 3D printer. Aging acceleration treatments using toothbrushing and thermocycling simulators were applied to half of the specimens corresponding to three years of usage in the oral environment (N = 10). Surface roughness (Ra), Vickers microhardness, 3-point bending, sorption, and solubility tests were performed. A 2-way analysis of variance (ANOVA) and Fisher’s multiple comparison test were used to compare the results among the groups. RESULTS. The mean surface roughness (Ra) of the resin after accelerated aging was significantly higher in the CO and ML groups than that before aging, but not in the 3D group. All groups showed reduced hardness after accelerated aging. The flexural strength values were highest in the 3D group, followed by the ML and CO groups after accelerated aging. Accelerated aging significantly reduced water sorption in the ML group. CONCLUSION. According to the tested material and 3D printer type, both 3D-printed and milled interim restoration resins showed higher flexural strength and modulus, and lower surface roughness than those prepared by the conventional method after accelerated aging.
Abstract
PURPOSE. This study assessed the physical and mechanical properties of interim crown materials fabricated using various digital techniques after accelerated aging. MATERIALS AND METHODS. Three groups of interim dental restorative materials (N = 20) were tested. The first group (CO) was fabricated using a conventional manual method. The second group (ML) was prepared from prefabricated resin blocks for the milling method and cut into specimensizes using a cutting disc. The third group (3D) was additively manufactured using a digital light-processing (DLP) 3D printer. Aging acceleration treatments using toothbrushing and thermocycling simulators were applied to half of the specimens corresponding to three years of usage in the oral environment (N = 10). Surface roughness (Ra), Vickers microhardness, 3-point bending, sorption, and solubility tests were performed. A 2-way analysis of variance (ANOVA) and Fisher’s multiple comparison test were used to compare the results among the groups. RESULTS. The mean surface roughness (Ra) of the resin after accelerated aging was significantly higher in the CO and ML groups than that before aging, but not in the 3D group. All groups showed reduced hardness after accelerated aging. The flexural strength values were highest in the 3D group, followed by the ML and CO groups after accelerated aging. Accelerated aging significantly reduced water sorption in the ML group. CONCLUSION. According to the tested material and 3D printer type, both 3D-printed and milled interim restoration resins showed higher flexural strength and modulus, and lower surface roughness than those prepared by the conventional method after accelerated aging.
참고문헌 (25)
- Abdullah AO, "Comparison between direct chairside and digitally fabricated temporary crowns", Dent Mater J, 37, pp.957~963 (2018)
- Al-Qahtani AS, "Surface properties of polymer resins fabricated with subtractive and additive manufacturing techniques", Polymers(Basel), 13, pp.4077~ (2021)
- Mai HN, "Fit of interim crowns fabricated using photopolymer-jetting 3D printing", J Prosthet Dent, 118, pp.208~215 (2017)
- Scotti CK, "Physical and surface properties of a 3D-printed composite resin for a digital workflow", J Prosthet Dent, 124, pp.614~ (2020)
- Peng CC, "Assessment of the internal fit and marginal integrity of interim crowns made by different manufacturing methods", J Prosthet Dent, 123, pp.514~522 (2020)
- Regish KM, "Techniques of fabrication of provisional restoration : an overview", Int J Dent, 2011, pp.134659~ (2011)
- Chen H, "Comparison of flexural properties and cytotoxicity of interim materials printed from mono-LCD and DLP 3D printers", J Prosthet Dent, 126, pp.703~708 (2021)
- Cheng CW, "Randomized clinical trial of a conventional and a digital workflow for the fabrication of interim crowns: An evaluation of treatment efficiency, fit, and the effect of clinician experience", J Prosthet Dent, 125, pp.73~81 (2021)
- 이완선, "Evaluation of internal fit of interim crown fabricated with CAD", CAM milling and 3D printing system, 2017, pp.9(4), 265~270[DOI]
- Tahayeri A, "3D printed versus conventionally cured provisional crown and bridge dental materials", Dent Mater, 34, pp.192~200 (2018)
- Alageel O, "Three-dimensional printing technologies for dental prosthesis : a review", Rapid Prototyp J, 28, pp.1764~1778 (2022)
- Kim D, "Effects of post-curing time on the mechanical and color properties of three-dimensional printed crown and bridge materials", Polymers, 12, pp.2762~ (2020)
- Simoneti DM, "Comparison of material properties and biofilm formation in interim single crowns obtained by 3D printing and conventional methods", J Prosthet Dent, 127, pp.168~172 (2022)
- Alageel O, "Removable partial denture alloys processed by laser-sintering technique", J Biomed Mater Res B Appl Biomater, 106, pp.1174~1185 (2018)
- Dikova T, "Dimensional accuracy and surface roughness of polymeric dental bridges produced by different 3D printing processes", Arch Mater Sci Eng, 94, pp.65~75 (2018)
- Goiato MC, "Effect of nanoscale particles incorporation on microhardness of polymers for oral prosthesis", Contemp Clin Dent, 7, pp.307~311 (2016)
- Ho TK, "The effect of chewing simulation on surface roughness of resin composite when opposed by zirconia ceramic and lithium disilicate ceramic", Dent Mater, 34, pp.e15~e24 (2018)
- Cha HS, "Wear resistance of 3D-printed denture tooth resin opposing zirconia and metal antagonists", J Prosthet Dent, 124, pp.387~394 (2020)
- Nayyer M, "Comparative abrasive wear resistance and surface analysis of dental resin-based materials", Eur J Dent, 12, pp.57~66 (2018)
- Shahmoradi M, "Mechanical failure of posterior teeth due to caries and occlusal wear-A modelling study", J Mech Behav Biomed Mater, 125, pp.104942~ (2022)
- Turssi CP, "Toothbrush bristle configuration and brushing load : Effect on the development of simulated non-carious cervical lesions", J Dent, 86, pp.75~80 (2019)
- Atalay S, "Effect of thermocycling on the surface properties of CAD-CAM denture base materials after different surface treatments", J Mech Behav Biomed Mater, 121, pp.104646~ (2021)
- Yao Q, "The effect of surface treatments on the color stability of CAD-CAM interim fixed dental prostheses", J Prosthet Dent, 126, pp.248~253 (2021)
- Gad MM, "Water sorption, solubility, and translucency of 3D-printed denture base resins", Dent J(Basel), 10, pp.42~ (2022)
- Angwarawong T, "Influence of thermomechanical aging on marginal gap of CAD-CAM and conventional interim restorations", J Prosthet Dent, 124, pp.566~ (2020)