레이저 용접조건이 극저온환경용 금속재료의 용접 비드 형상에 미치는 영향에 대한 연구 Part II : STS304L, STS316L
Research for Correlation Between Shape of Bead on Plate and Laser Welding Condition of Cryogenic Materials Part II : STS304L, STS316L
1
조회
0
다운로드
6
인용
0
참고문헌
키워드
초록
As the part of efforts to respond to the environmental pollution, the demand for clean energy is increasing. Natural gas is one of the most realistic alternatives, and interest in the storage and transportation containers to utilize the natural gas is growing. The production area of natural gas is limited, and in Korea, it is imported in the form of liquefied natural gas. LNG is a cryogenic state with a vaporization point of -163°C, so the ordinary metal cannot be used due to its brittleness. The international maritime organization (IMO) defines the metals that can handle LNG in the IGC Code, and the research is ongoing. This study was a preliminary study to check the weldability of related metals and confirmed the shape of bead on plate (BOP) during the laser welding for each material. In part I, a study was conducted on the high manganese steel, and in part II, a study was conducted on the materials of STS304L and STS316L among the stainless steel. Based on this study, it can be used as an optimal welding condition for the butt and fillet welding.
Abstract
As the part of efforts to respond to the environmental pollution, the demand for clean energy is increasing. Natural gas is one of the most realistic alternatives, and interest in the storage and transportation containers to utilize the natural gas is growing. The production area of natural gas is limited, and in Korea, it is imported in the form of liquefied natural gas. LNG is a cryogenic state with a vaporization point of -163°C, so the ordinary metal cannot be used due to its brittleness. The international maritime organization (IMO) defines the metals that can handle LNG in the IGC Code, and the research is ongoing. This study was a preliminary study to check the weldability of related metals and confirmed the shape of bead on plate (BOP) during the laser welding for each material. In part I, a study was conducted on the high manganese steel, and in part II, a study was conducted on the materials of STS304L and STS316L among the stainless steel. Based on this study, it can be used as an optimal welding condition for the butt and fillet welding.
참고문헌 (11)
- O. Schinas, "Feasibility and commercial considerations of LNG-fueled ships", Ocean Eng, 122, pp.84~96 (2016)
- B. Y. Yoo, "Economic assessment of liquefied natural gas(LNG)as a marine fuel for CO2 carriers compared to marine gas oil(MGO)", Energy, 121, pp.772~780 (2017)
- H. Thomson, "Natural gas as a marine fuel", Energy Policy, 87, pp.153~167 (2015)
- 이진성, "An experimental study on fatigue performance of cryogenic metallic materials for IMO type B tank", International Journal of Naval Architecture and Ocean Engineering, 5(4), pp.580~597 (2013), 대한조선학회
- IMO, "Sub-Committee on Carriage of Cargoes and Containers (CCC), 5th session 10-14 September 2018", ~ (2018)
- 김재웅, "A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel PART I : Proposal of a heat source model", International Journal of Naval Architecture and Ocean Engineering, 5(3), pp.348~363 (2013), 대한조선학회
- 이목영, "마그네슘 박판 겹치기 이음부의 레이저 용접성에 관한 연구", 대한용접접합학회지, 37(4), pp.293~298 (2019), 대한용접접합학회[DOI]
- Z. Zeng, "Functional fatigue behavior of NiTi-Cu dissimilar laser welds", Mater. Des, 114, pp.282~287 (2017)
- 김용, "스틸과 알루미늄의 이종재 레이저 용접특성", 대한용접접합학회지, 35(5), pp.16~22 (2017), 대한용접접합학회[DOI]
- Jaewoong Kim, "Laser Welding of ASTM A553-1 (9% Nickel Steel) (PART I: Penetration Shape by Bead on Plate)", Metals, 10(4), pp.484~ (2020), MDPI AG[DOI]
- Changmin Pyo, "Estimation of Heat Source Model’s Parameters for GMAW with Non-linear Global Optimization—Part I: Application of Multi-island Genetic Algorithm", Metals, 10(7), pp.885~ (2020), MDPI AG[DOI]