레이저 용접조건이 극저온환경용 금속재료의 용접 비드 형상에 미치는 영향에 대한 연구 Part III : 알루미늄(AL5083)
Research for Correlation Between Shape of Bead on Plate and Laser Welding Condition of Cryogenic Materials Part III : Aluminium (AL5083)
1
조회
0
다운로드
5
인용
0
참고문헌
키워드
초록
Natural gas is the most realistic fuel among eco-friendly fuels. Natural gas production is limited, and in Korea, it is supplied and utilized in the form of liquefied natural gas (LNG). In the case of LNG, the vaporization point is 163 degrees below zero, so ordinary metal cannot be used due to its brittleness. The International Maritime Organization (IMO) defines metals that can be used in the IGC Code, and is used for storage containers, transportation containers, etc. based on the metals. Welding is essential in the manufacture of large structures such as LNG storage tanks. In this study, weldability studies related to cryogenic materials were conducted. In Part I of this study, high-manganese steel and part II were studied for two types of stainless steel (STS304L, STS316L), and in Part III, aluminum (AL5083). During laser welding, the shape of the Bead on Plate (BOP) was analyzed, and a total of nine cases were analyzed using laser power and welding speed as variables. It was confirmed that the penetration and the width of the welding width were linearly proportional to the amount of heat input. Based on this study, it is possible to conduct a follow-up study to find the optimal welding conditions for butt welding and fillet welding.
Abstract
Natural gas is the most realistic fuel among eco-friendly fuels. Natural gas production is limited, and in Korea, it is supplied and utilized in the form of liquefied natural gas (LNG). In the case of LNG, the vaporization point is 163 degrees below zero, so ordinary metal cannot be used due to its brittleness. The International Maritime Organization (IMO) defines metals that can be used in the IGC Code, and is used for storage containers, transportation containers, etc. based on the metals. Welding is essential in the manufacture of large structures such as LNG storage tanks. In this study, weldability studies related to cryogenic materials were conducted. In Part I of this study, high-manganese steel and part II were studied for two types of stainless steel (STS304L, STS316L), and in Part III, aluminum (AL5083). During laser welding, the shape of the Bead on Plate (BOP) was analyzed, and a total of nine cases were analyzed using laser power and welding speed as variables. It was confirmed that the penetration and the width of the welding width were linearly proportional to the amount of heat input. Based on this study, it is possible to conduct a follow-up study to find the optimal welding conditions for butt welding and fillet welding.
참고문헌 (12)
- O. Schinas, "Feasibility and commercial considerations of LNG-fueled ships", Ocean Eng, 122, pp.84~96 (2016)
- B. Y. Yoo, "Economic assessment of liquefied natural gas(LNG)as a marine fuel for CO2 carriers compared to marine gas oil(MGO)", Energy, 121, pp.772~780 (2017)
- H. Thomson, "Natural gas as a marine fuel", Energy Policy, 87, pp.153~167 (2015)
- 이진성, "An experimental study on fatigue performance of cryogenic metallic materials for IMO type B tank", International Journal of Naval Architecture and Ocean Engineering, 5(4), pp.580~597 (2013), 대한조선학회
- IMO, "Sub-Committee on Carriage of Cargoes and Containers (CCC), 5th session 10-14 September 2018", ~ (2018)
- 김재웅, "A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel PART I : Proposal of a heat source model", International Journal of Naval Architecture and Ocean Engineering, 5(3), pp.348~363 (2013), 대한조선학회
- 이목영, "마그네슘 박판 겹치기 이음부의 레이저 용접성에 관한 연구", 대한용접접합학회지, 37(4), pp.293~298 (2019), 대한용접접합학회[DOI]
- Z. Zeng, "Functional fatigue behavior of NiTi-Cu dissimilar laser welds", Mater. Des, 114, pp.282~287 (2017)
- 김용, "스틸과 알루미늄의 이종재 레이저 용접특성", 대한용접접합학회지, 35(5), pp.16~22 (2017), 대한용접접합학회[DOI]
- Jaewoong Kim, "Laser Welding of ASTM A553-1 (9% Nickel Steel) (PART I: Penetration Shape by Bead on Plate)", Metals, 10(4), pp.484~ (2020), MDPI AG[DOI]
- Changmin Pyo, "Estimation of Heat Source Model’s Parameters for GMAW with Non-linear Global Optimization—Part I: Application of Multi-island Genetic Algorithm", Metals, 10(7), pp.885~ (2020), MDPI AG[DOI]
- Guodong Zhu, "Investigation on the Surface Properties of 5A12 Aluminum Alloy after Nd: YAG Laser Cleaning", Coatings, 9(9), pp.578~ (2019), MDPI AG[DOI]