레이저 용접조건이 극저온환경용 금속재료의 용접 비드 형상에 미치는 영향에 대한 연구Part I : 고망간강
Research for Correlation Between Shape of Bead on Plate and Laser Welding Condition of Cryogenic Materials Part I : High Manganese Steel
4
조회
0
다운로드
4
인용
0
참고문헌
키워드
초록
As demand for eco-friendly energy increases, demand for natural gas and Liquefied natural gas (LNG) storage technologies continues to increase. LNG is a cryogenic environment with a temperature of -163°C, so ordinary metals cannot be used due to brittleness. Accordingly, IGC Code designates the cryogenic materials such as Invar, STS304L, Al5083-0, and High Manganese Steel. For fabricating those materials, research on welding possibility is the most important. Thus this study focused on the possibility of laser welding of the cryogenic materials. The weldability of High Manganese Steel was researched in this paper, the shape and the dimensions of the beads after bead on plate (BOP) welding were observed. The experiment was conducted on a total of 25 cases with laser power and welding speed of 5 cases each, and the width, height, and penetration of the beads were confirmed. It was confirmed that the paramenter of bead increased linearly with the laser power, and the paramenters of bead increased linearly with decreasing welding speed. Based on this study, high manganese steel can be applied in various industries by applying it to butt welding.
Abstract
As demand for eco-friendly energy increases, demand for natural gas and Liquefied natural gas (LNG) storage technologies continues to increase. LNG is a cryogenic environment with a temperature of -163°C, so ordinary metals cannot be used due to brittleness. Accordingly, IGC Code designates the cryogenic materials such as Invar, STS304L, Al5083-0, and High Manganese Steel. For fabricating those materials, research on welding possibility is the most important. Thus this study focused on the possibility of laser welding of the cryogenic materials. The weldability of High Manganese Steel was researched in this paper, the shape and the dimensions of the beads after bead on plate (BOP) welding were observed. The experiment was conducted on a total of 25 cases with laser power and welding speed of 5 cases each, and the width, height, and penetration of the beads were confirmed. It was confirmed that the paramenter of bead increased linearly with the laser power, and the paramenters of bead increased linearly with decreasing welding speed. Based on this study, high manganese steel can be applied in various industries by applying it to butt welding.
참고문헌 (11)
- O. Schinas, "Feasibility and commercial considerations of LNG-fueled ships", Ocean Eng, 122, pp.84~96 (2016)
- B. Y. Yoo, "Economic assessment of liquefied natural gas(LNG)as a marine fuel for CO2 carriers compared to marine gas oil(MGO)", Energy, 121, pp.772~780 (2017)
- H. Thomson, "Natural gas as a marine fuel", Energy Policy, 87, pp.153~167 (2015)
- J. S. Lee, "An experimental study on fatigue performance of cryogenic metallic materials for IMO type B tank", Int. J. Nav. Arch. Ocean, 5, pp.580~597 (2013)
- IMO, "Sub-Committee on Carriage of Cargoes and Containers (CCC), 5th session 10-14", ~ (2018)
- 김재웅, "A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel PART I : Proposal of a heat source model", International Journal of Naval Architecture and Ocean Engineering, 5(3), pp.348~363 (2013), 대한조선학회
- 이목영, "마그네슘 박판 겹치기 이음부의 레이저 용접성에 관한 연구", 대한용접접합학회지, 37(4), pp.293~298 (2019), 대한용접접합학회[DOI]
- Z. Zeng, "Functional fatigue behavior of NiTi-Cu dissimilar laser welds", Mater. Des, 114, pp.282~287 (2017)
- 김용, "스틸과 알루미늄의 이종재 레이저 용접특성", 대한용접접합학회지, 35(5), pp.16~22 (2017), 대한용접접합학회[DOI]
- Jaewoong Kim, "Laser Welding of ASTM A553-1 (9% Nickel Steel) (PART I: Penetration Shape by Bead on Plate)", Metals, 10(4), pp.484~ (2020), MDPI AG[DOI]
- Changmin Pyo, "Estimation of Heat Source Model’s Parameters for GMAW with Non-linear Global Optimization—Part I: Application of Multi-island Genetic Algorithm", Metals, 10(7), pp.885~ (2020), MDPI AG[DOI]