선박 극저온 탱크용 9% 니켈강 소재 FCAW 맞대기 용접 연구 PART I : 용접부 신뢰성 연구
A Study on FCAW Butt Welds of 9% Nickel Steel Materials for Vessel Cryogenic Tank Part I : Reliability Study of Welding Bead
5
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Because of the International Maritime Organization(IMO)'s regulation to regulate emissions of ships, a change is taking place to replace ship fuels from Heavy Fule Oil(HFO) to Liquefied Natural Gas(LNG). In the case of LNG, it is a material obtained by liquefying Natural Gas(NG), and it is -163 degrees below zero, and the volume is reduced to 1/600 level. The material of the tank that can store LNG must be a material that can safely store LNG in a cryogenic environment, and the materials of the tank that can store LNG are limited in the International Code of the Construction and Equipment of Ships Carrying Liquefied Gases in Bulk(IGC Code). Among the materials listed in the IGC Code, 9% nickel steel is used as a material for LNG fuel propulsion tanks that are recently ordered because of relatively high mechanical properties under cryogenic environments. In this study, butt welding was performed on a 9% nickel steel material using Flux Cored Arc Welding(FCAW), the most widely used welding method in shipyards. In PARTI, after securing the welding conditions, cross-sectional observation results analysis, liquid penetrating test, and radiographic test were performed to verify the reliability of the weld.
Abstract
Because of the International Maritime Organization(IMO)'s regulation to regulate emissions of ships, a change is taking place to replace ship fuels from Heavy Fule Oil(HFO) to Liquefied Natural Gas(LNG). In the case of LNG, it is a material obtained by liquefying Natural Gas(NG), and it is -163 degrees below zero, and the volume is reduced to 1/600 level. The material of the tank that can store LNG must be a material that can safely store LNG in a cryogenic environment, and the materials of the tank that can store LNG are limited in the International Code of the Construction and Equipment of Ships Carrying Liquefied Gases in Bulk(IGC Code). Among the materials listed in the IGC Code, 9% nickel steel is used as a material for LNG fuel propulsion tanks that are recently ordered because of relatively high mechanical properties under cryogenic environments. In this study, butt welding was performed on a 9% nickel steel material using Flux Cored Arc Welding(FCAW), the most widely used welding method in shipyards. In PARTI, after securing the welding conditions, cross-sectional observation results analysis, liquid penetrating test, and radiographic test were performed to verify the reliability of the weld.
참고문헌 (17)
- K. Li, "Determinants of ship operators’ options for compliance with IMO 2020", Transportation Research Part D: Transport and Environment, 86, pp.102459~ (2020)
- 이진성, "An experimental study on fatigue performance of cryogenic metallic materials for IMO type B tank", International Journal of Naval Architecture and Ocean Engineering, 5(4), pp.580~597 (2013), 대한조선학회
- M. Tayebi, "Comparative study of AISI 304L to AISI 316L stainless steels joints by TIG and Nd : YAG laser welding", Journal of Alloys and Compounds, 767, pp.112~121 (2018)
- 김지선, "레이저 용접조건이 극저온환경용 금속재료의 용접 비드 형상에 미치는 영향에 대한 연구 Part II : STS304L, STS316L", 한국기계기술학회지, 22(4), pp.733~739 (2020), 한국기계기술학회[DOI]
- Yang Woosung, "Tensile and Microstructural Behaviors of Austenitic Stainless Steel GTA Welds for Cryogenic Application", 대한용접접합학회지, 38(4), pp.400~408 (2020), 대한용접접합학회[DOI]
- K. Jang, "Welding and environmental test condition effect in weldability and strength of Al alloy", Journal of Materials Processing Technology, 164-165, pp.1038~1045 (2005)
- F. Heirani, "Effects of processing parameters on microstructure and mechanical behaviors of underwater friction stir welding of Al5083 alloy", Journal of Manufacturing Processes, 25, pp.77~84 (2017)
- 표창민, "레이저 용접조건이 극저온환경용 금속재료의 용접 비드 형상에 미치는 영향에 대한 연구 Part III : 알루미늄(AL5083)", 한국기계기술학회지, 22(4), pp.747~751 (2020), 한국기계기술학회[DOI]
- K. Nohara, "Fe-36% Ni invar type alloy KLN 36 for LNG Facilities", Kawasaki steel technical report, 13, pp.97~108 (1985)
- 한종만, "LNG선 화물격납용기 Invar strake edge 이음부 형상 개선에 관한 연구", 대한용접접합학회지, 27(5), pp.74~80 (2009), 대한용접접합학회
- D. S. Kim, "A Study on Cross-Shaped Structure of Invar Material Using Cold Wire Laser Fillet Welding(PART I : Feasibility Study for Weldability)", Metals, 10(10), pp.1385~2020 (2020)
- I. Han, "Microstructure and Mechanical Properties of Cryogenic High-Manganese Steel Weld Metal", International Journal of Offshore and Polar Engineering, 27(3), pp.348~352 (2013)
- 한일욱, "Ni가 첨가된 고망간 용접봉의 입열량에 따른 인장 특성과 미세조직의 영향", 대한용접접합학회지, 36(1), pp.10~17 (2018), 대한용접접합학회[DOI]
- 표창민, "선박 극저온 탱크용 고망간강 소재 맞대기 용접부 기계 물성 분석 연구", 한국기계기술학회지, 22(6), pp.1123~1128 (2020), 한국기계기술학회[DOI]
- 김보언, "9 wt.% 니켈강 소재를 활용한 선박용 LNG Fuel Tank 초기 설계 및 용접부 성능 평가", 대한용접접합학회지, 37(6), pp.555~563 (2019), 대한용접접합학회[DOI]
- J. Kim, "Laser Welding of ASTM A553-1(9% Nickel Steel)(PART I : Penetration Shape by Bead on Plate)", Metals, 10(4), pp.484~ (2020)
- J. Kim, "Laser Welding of ASTM A553-1(9% Nickel Steel)(PART II : Comparison of Mechanical Properties with FCAW)", Metals, 10(8), pp.999~ (2020)