3D 프린팅을 이용한 손 엑스선 검사 보조도구의 유용성
Usefulness of an Auxiliary Tool for Hand Radiography by Using 3D Printing
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
As an auxiliary tool for fixing the patient's posture when taking an X-ray, sponges with high radiolucencies are laminated in various thicknesses. This study aimed to evaluate the usefulness of an auxiliary tool for hand oblique projection X-ray by manufacturing it with a uniform thickness by 3D printing and comparing it with existing sponge tools. In the auxiliary tool, radiolucency was measured at the stairs where each finger was located, and pixel information values were compared in the digital imaging and communications in medicine(DICOM) image. Contrast to noise ratio(CNR) and signal to noise ratio(SNR) were compared by shooting the hand phantom and the auxiliary tool together. As the thickness of the sponge tool increased, radiolucency decreased by 15.52% and pixel information value increased by 20.61%. The transmittance of the 3D printing tool increased by 0.82%, and the pixel information value differed by 5.66%. CNR and SNR increased by 20.03% and 22.42% in 3D printing compared to existing sponge tools. while taking hand oblique projection, maintaining the thickness of the auxiliary tool uniformly through 3D printing maintains high radiolucency and minimal impact on medical images, and increases CNR and SNR, making it useful as an auxiliary tool for taking hand oblique projection.
Abstract
As an auxiliary tool for fixing the patient's posture when taking an X-ray, sponges with high radiolucencies are laminated in various thicknesses. This study aimed to evaluate the usefulness of an auxiliary tool for hand oblique projection X-ray by manufacturing it with a uniform thickness by 3D printing and comparing it with existing sponge tools. In the auxiliary tool, radiolucency was measured at the stairs where each finger was located, and pixel information values were compared in the digital imaging and communications in medicine(DICOM) image. Contrast to noise ratio(CNR) and signal to noise ratio(SNR) were compared by shooting the hand phantom and the auxiliary tool together. As the thickness of the sponge tool increased, radiolucency decreased by 15.52% and pixel information value increased by 20.61%. The transmittance of the 3D printing tool increased by 0.82%, and the pixel information value differed by 5.66%. CNR and SNR increased by 20.03% and 22.42% in 3D printing compared to existing sponge tools. while taking hand oblique projection, maintaining the thickness of the auxiliary tool uniformly through 3D printing maintains high radiolucency and minimal impact on medical images, and increases CNR and SNR, making it useful as an auxiliary tool for taking hand oblique projection.
참고문헌 (18)
- Korean Society of Medical Imaging Technology, "Textbook of radiographic positioning and clinical diagnosis. Vol. 1", pp.76~78 (2019), Chung-Ku Publisher
- 임우택, "응급실 침대 위 흉부전후방향 엑스선 검사를 위한 상의고정장치 개발", 방사선기술과학, 45(3), pp.205~211 (2022), 대한방사선과학회
- 엄소영, "슬관절의 측면 방사선 촬영에서 보조기구를 이용한 검사방법의 정확성과 편의성에 대한 연구", 한국방사선학회논문지, 11(4), pp.253~262 (2017), 한국방사선학회[DOI]
- 이도병, "슬개골 엑스선 영상 촬영을 위한 보조기구의 개발과 활용", 의공학회지, 41(4), pp.165~171 (2020), 대한의용생체공학회
- 이도병, "방사선촬영 보조기구를 이용한 어린이 흉부 엑스선 검사에 관한 연구", 의공학회지, 39(1), pp.48~54 (2018), 대한의용생체공학회
- Choi OR, "Evaluation of usefulness of the device when taking a wrist lateral radial tilt view", Journal of Korean Society of Radiologocal Imaging Technology, 2014(1), pp.1~8 (2014)
- 박지군, "피사체 두께에 따른 산란선 발생이 화질에 미치는 영향", 한국방사선학회논문지, 11(7), pp.671~677 (2017), 한국방사선학회[DOI]
- Seo JH, "Investigation of scattered radiation on images effect in digital radiography", Journal of the Korean Society of Radiology, 8(1), pp.77~79 (2014)[DOI]
- 장정현, "영상의학과 촬영실의 미생물 분포에 관한 연구", 한국방사선학회논문지, 15(2), pp.165~171 (2021), 한국방사선학회[DOI]
- 홍동희, "영상의학과 응급실내의 일반촬영장비와 전산화단층촬영장비 표면에서의 세균 오염에 관한 분석", 방사선기술과학, 39(3), pp.421~427 (2016), 대한방사선과학회[DOI]
- 김상현, "Law법 수직입사를 위한 보조기구의 3D 프린터 제작 연구", 방사선기술과학, 43(6), pp.489~494 (2020), 대한방사선과학회
- 김형균, "허리뼈 사방향 X-선 검사에서 3D 프린팅으로 제작된 보조기구의 임상적 유용성 평가", 한국방사선학회논문지, 16(5), pp.505~512 (2022), 한국방사선학회[DOI]
- 김형균, "의료영상 검사를 위한 상지 보조기구의 3D 프린터 제작 연구", 방사선기술과학, 38(4), pp.389~394 (2015), 대한방사선과학회[DOI]
- Yoon MS, "The study of making an assistance device in hand lateral examination using 3D printer", Journal of the Korean Society of Radiological Imageing Technology, 2018(1), pp.119~123 (2018)
- 조용인, "인터벤션 시술 시 환자의 선량감소를 위한 3D 프린팅 재료의 적용성 평가", 방사선기술과학, 43(3), pp.169~176 (2020), 대한방사선과학회
- 윤준, "일반촬영분야에서의 3D 프린터로 제작한 텅스텐 혼합 필라멘트 차폐체의 성능평가", 방사선기술과학, 44(6), pp.615~621 (2021), 대한방사선과학회
- "Utilization of 3D printing technology in the mold industry used in shipbuilding, energy, heavy industry and automobiles" (2020)[URL]
- 문준호, "엑스선 촬영 시 보조도구 재료로써 탄소 섬유 강화 플라스틱의 유용성", 방사선기술과학, 46(3), pp.197~205 (2023), 대한방사선과학회