3D 프린팅 기술을 이용한 전산화단층영상 기반 조직 생검 보조기구 개발
Development of Biopsy Assist Device on Computed Tomography Using 3D Printing Technology
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
The purpose of this study was to develop an assist device that could correct and support patient position during biopsy on computed tomography (CT) using 3D printing technology. The development method was conducted in the order of 3D design, 3D output, intermediate evaluation for product, final assist device evaluation. The 3D design method was conducted in the order of prior research data survey, measurement, primary modeling, 3D printing, output evaluation, and supplementary modeling. The 3D output was the 3D printer (3DWOX 2X, Sindoh, Korea) with additive manufacturing technology and the polylactic acid (PLA) materials. At this time, the optimal strength was evaluated to infill degree of product as the 3D printing factors into 20%, 40%, 60%, and 80%. The intermediate evaluation and supplementation was measured noise in the region of interest (ROI) around the beam hardening artifact on the CT images. We used 128-channel MDCT (Discovery 75 HD, GE, USA) to scan with a slice thickness of 100 kVp, 150 mA, and 2.5 mm on the 3D printing product. We compared the surrounding noise of the final 3D printing product with the beginning of it. and then the strength of it according to the degree of infill was evaluated. As a result, the surrounding noise of the final and the early devices were measured at an average of 3.3 ± 0.5 HU and 7.1 ± 0.1 HU, respectively, which significantly reduced the noise of the final 3D printing product (p<0.001). We found that the percentage of infill according to the optimal strength was found to be 60%. Finally, development of assist devices for CT biopsy will be able to minimize artifacts and provide convenience to medical staff and patients.
Abstract
The purpose of this study was to develop an assist device that could correct and support patient position during biopsy on computed tomography (CT) using 3D printing technology. The development method was conducted in the order of 3D design, 3D output, intermediate evaluation for product, final assist device evaluation. The 3D design method was conducted in the order of prior research data survey, measurement, primary modeling, 3D printing, output evaluation, and supplementary modeling. The 3D output was the 3D printer (3DWOX 2X, Sindoh, Korea) with additive manufacturing technology and the polylactic acid (PLA) materials. At this time, the optimal strength was evaluated to infill degree of product as the 3D printing factors into 20%, 40%, 60%, and 80%. The intermediate evaluation and supplementation was measured noise in the region of interest (ROI) around the beam hardening artifact on the CT images. We used 128-channel MDCT (Discovery 75 HD, GE, USA) to scan with a slice thickness of 100 kVp, 150 mA, and 2.5 mm on the 3D printing product. We compared the surrounding noise of the final 3D printing product with the beginning of it. and then the strength of it according to the degree of infill was evaluated. As a result, the surrounding noise of the final and the early devices were measured at an average of 3.3 ± 0.5 HU and 7.1 ± 0.1 HU, respectively, which significantly reduced the noise of the final 3D printing product (p<0.001). We found that the percentage of infill according to the optimal strength was found to be 60%. Finally, development of assist devices for CT biopsy will be able to minimize artifacts and provide convenience to medical staff and patients.
참고문헌 (18)
- Kitamori H, "Evaluation of mouthpiece fixation devices for head and neck radiotherapy patients fabricated in Polyjet photopolymer by a 3D printer", Physica Medica, 58, pp.90~98 (2019)
- Santos JC, "Charaterization and applicability of low-density materials for making 3D physical anthropomorphic breast phantoms", Radiation Physics and Chemistry, 164, pp.108361~ (2019)
- Kadoya N, "Evaluation of a 3D-printed heterogeneous anthropomorphic head and neck phantom for patient-specific quality assurance in intensitymodulated radiation therapy", Radiological Physics and Technology, 12, pp.351~356 (2019)
- Herrmann KH, "3D printing of MRI compatible components : Why every MRI research group should have a low-budget 3D printer", Medical Engineering & Physics, 36(10), pp.1373~1380 (2014)
- Iguchi T, "CT fluoroscopy-guided biopsy of pulmonary lesions contacting theinterlobar fissure : An analysis of 72 biopsies", Diagnostic and Interventional Imaging, 103(6), pp.302~309 (2022)
- Saji H, "The incidence and the risk ofpneumothorax and chest tube placement after percutaneous CT-guided lungbiopsy : The angle of the needle trajectory is a novel predictor", Chest, 121, pp.1521~1526 (2002)
- Kim DG, "Evaluation of the Efficiency of Use of Fixation Instrumens in Computed Tomography-Guided Biopsy of Lung Lesions", The Journal of the Korea Contents Association, 22(7), pp.676~683 (2022)
- Neyaz Z, "Soft-Tip Stylet and Saline Instillation Technique : Making Difficult Percutaneous CT-GuidedBiopsies Possible", Indian Journal of Radiology & Imaging, 31(4), pp.956~960 (2021)
- Lehmann S, "An Overview of Percutaneous CT-Guided Lung Biopsies", Journal of Radiology Nursing, 37(1), pp.2~8 (2018)
- Pessis E, "Virtual monochromatic spectral imaging with fast kilovoltage switching : Reduction of metal artifacts at CT", RadioGraphics, 33(2), pp.573~583 (2013)
- 성열훈, "3차원 프린팅 적층가공 방식에서 매질 내부 충전이 초음파 속도와 감쇠에 미치는 영향", 방사선기술과학, 41(1), pp.53~60 (2018), 대한방사선과학회[DOI]
- Sugawara H, "New Fast kVp Switching Dual-Energy CT : Reduced Severity of Beam Hardening Artifacts and Improved Image Quality in Reduced-Iodine Virtual Monochromatic Imaging", Academic Radiology, 27(11), pp.1586~1593 (2020)
- 김명세, "전신 방사선치료(Total Body Irradiation, TBI)를 위한 한국인에 맞는 환자 고정장치에 관한 연구", 의학물리, 13(3), pp.114~119 (2002), 한국의학물리학회
- Savi M, "Commercial filament testing for use in 3D printed phantoms", Radiation Physics and Chemistry, 174, pp.108906~ (2020)
- Hong DY, "Development of a CT imaging phantom of anthromorphic lung using fused deposition modeling 3D printing", Medicine, 99(1), pp.e18617~ (2020)
- Ballard DH, "Clinical Applications of 3D Printing : Primer for the Radiologists", Academic Radiology, 25(1), pp.52~65 (2018)
- 홍다영, "3D 프린팅기술을 이용한 골밀도 정도관리 대퇴골 팬텀 제작 및 유용성 평가", 방사선기술과학, 46(1), pp.1~8 (2023), 대한방사선과학회
- 이주영, "PET", CT 팬텀의 3D 프린팅 소재 적용 가능성 평가, 2022, pp.45(5), 423~431[DOI]