3C-SiC 마이크로 히터의 제작과 그 특성
Fabrication of 3C-SiC micro heaters and its characteristics
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
This paper describes the characteristics of a poly 3C-SiC micro heater which was fabricated on AlN(0.1 μm)/3CSiC(1.0 μm) suspended membranes by surface micro-machining technology. The 3C-SiC and AlN thin films which have wide energy band gap and very low lattice mismatch were used sensors for high temperature and voltage environments. The 3C-SiC thin film was used as micro heaters and temperature sensor materials simultaneously. The implemented 3CSiC RTD(resistance of temperature detector) and the power consumption of micro heaters were measured and calculated. The TCR(thermal coefficient of the resistance) of 3C-SiC RTD is about −5200 ppm/℃ within a temperature range from 25℃ to 50℃ and −1040 ppm/℃ at 500℃. The micro heater generates the heat about 500℃ at 10.3 mW. Moreover, durability of 3C-SiC micro heaters in high voltages is better than Pt micro heaters. A thermal distribution measured and simulated by IR thermovision and COMSOL is uniform on the membrane surface.
Abstract
This paper describes the characteristics of a poly 3C-SiC micro heater which was fabricated on AlN(0.1 μm)/3CSiC(1.0 μm) suspended membranes by surface micro-machining technology. The 3C-SiC and AlN thin films which have wide energy band gap and very low lattice mismatch were used sensors for high temperature and voltage environments. The 3C-SiC thin film was used as micro heaters and temperature sensor materials simultaneously. The implemented 3CSiC RTD(resistance of temperature detector) and the power consumption of micro heaters were measured and calculated. The TCR(thermal coefficient of the resistance) of 3C-SiC RTD is about −5200 ppm/℃ within a temperature range from 25℃ to 50℃ and −1040 ppm/℃ at 500℃. The micro heater generates the heat about 500℃ at 10.3 mW. Moreover, durability of 3C-SiC micro heaters in high voltages is better than Pt micro heaters. A thermal distribution measured and simulated by IR thermovision and COMSOL is uniform on the membrane surface.
참고문헌 (10)
- J. C. Lee, "Electrical, thermal, and mechanical characterization of silicon microcantilever heaters", J. Microelectromech. Syst, 15(6), pp.1644~1655 (2006)
- G. Wiche, "Thermal analysis of silicon carbide based micro hotplates for metal oxide gas sensors", Sen. Actu. A, 123, pp.12~17 (2005)
- 한기봉, "순 아르콘 캐리어 가스와 APCVD로 성장된 다결정 3C-SiC 박막의 기계적 특성", 센서학회지, 16(4), pp.319~323 (2007), 한국센서학회
- 정귀상, "AlN 버퍼층위에 성장된 M", NEMS용 다결정 3C-SiC 박막의 특성, 2007, pp.16(6), 457~461[DOI]
- 정귀상, "고온 화학센서용 다결정 3C-SiC 쇼트키 다이오드 제작과 그 특성", 센서학회지, 17(6), pp.414~417 (2008), 한국센서학회
- 정귀상, "마그네트론 RIE을 이용한 M", NEMS용 다결정 3C-SiC 식각 연구, 2007, pp.16(3), 197~201[DOI]
- J. Zhang, "Electrical, mechanical and metal contact properties of polycrystalline 3C-SiCfilms for MEMS in harsh environments", Surf. Coat. Tech, 201, pp.8893~8898 (2007)
- F. Solzbacher, "A modular system of SiC-based microhotplates for the application in metal oxide gas sensors", Sen. Actu. B, 64, pp.95~101 (2000)
- J. Courbat, "Reliability improvement of suspended platinum-based micro- heating elements", Sen. Actu. A, 142, pp.284~291 (2008)
- Zs. Vizvary, "Thermomechanical analysis of hotplates by FEM", J. Microelectronics, 32, pp.833~837 (2001)