복합재료/금속 접착 계면의 파괴인성치 측정
Interfacial Fracture Toughness Measurement of Composite/metal Bonding
1
조회
0
다운로드
4
인용
0
참고문헌
키워드
초록
Prediction of the load-bearing capacity of an adhesive-bonded joint is of practical importance for engineers. This paper introduces interface fracture mechanics approach to predict the load-bearing capacity of composite/metal bonded joints. The adhesion strength of composite/steel bonding is evaluated in terms of the energy release rate of an interfacial crack and the fracture toughness of the interface. Virtual crack closure technique (VCCT) is used to calculate energy release rates, and bi-material end-notched flexure (ENF) specimens are devised to measure the interfacial fracture toughness. Bi-material ENF specimens gave consistent mode II fracture toughness (GIIc) values of the composite/steel interface regardless of the thickness of specimens. The critical energy release rates of double-lap joints showed a good agreement with the measured fracture toughness. Therefore, the energy-based interfacial fracture characterization can be a practical engineering tool for predicting the load-bearing capacity of bonded joints.
Abstract
Prediction of the load-bearing capacity of an adhesive-bonded joint is of practical importance for engineers. This paper introduces interface fracture mechanics approach to predict the load-bearing capacity of composite/metal bonded joints. The adhesion strength of composite/steel bonding is evaluated in terms of the energy release rate of an interfacial crack and the fracture toughness of the interface. Virtual crack closure technique (VCCT) is used to calculate energy release rates, and bi-material end-notched flexure (ENF) specimens are devised to measure the interfacial fracture toughness. Bi-material ENF specimens gave consistent mode II fracture toughness (GIIc) values of the composite/steel interface regardless of the thickness of specimens. The critical energy release rates of double-lap joints showed a good agreement with the measured fracture toughness. Therefore, the energy-based interfacial fracture characterization can be a practical engineering tool for predicting the load-bearing capacity of bonded joints.
참고문헌 (15)
- Kinloch A.J, "Adhesion and Adhesives: science and technology" (1987), Chapman and Hall
- Pocius A.V, "Adhesion and Adhesives Technology: An introduction" (1997), Hanser Publishers
- Tong L, "An assessment of failure criteria to predict the strength of adhesively bonded composite doubler Lap Joints", Journal of Reinforced Plastics and Composites, 16(18), pp.698~713 (1997)
- 김광수, "일방향 복합재료 Single Lap 접합 조인트의 파손 모드 및 파손 강도 II. 파손 예측", Advanced Composite Materials, 18(1), pp.1~9 (2005), 한국복합재료학회
- Anderson G.P, "Predicting bond strength", Journal of Adhesion, 23, pp.289~302 (1987)
- Anderson G.P, "Predicting strength of adhesive joints from test results", International Journal of Fracture, 39, pp.191~200 (1989)
- Reedy E.D, "Comparison of butt tensile strength data with interface corner stress intensity factor prediction", International Journal of Solids and Structures, 30(21), pp.2929~2936 (1993)
- Qian Z.Q, "An experimental investigation of failure initiation in bonded joints", Acta materia, 46(14), pp.4895~4904 (1998)
- Akisanya A.R, "Interfacial cracking from the free edge of a long bi-material strip", International Journal of Solids and Structures, 34, pp.1645~1665 (1997)
- 김원석, "복합재료-탄소강 접착제 결합 조인트의 하중지지 능력 예측을 위한 이종 재료 접합 계면의 파괴 역학적 분석", Advanced Composite Materials, 19(4), pp.15~22 (2006), 한국복합재료학회
- Irwin G.R, "Analysis of stresses and strains near the end of a crack traversing a plate", Journal of Applied Mechanics, 24, pp.361~364 (1957)
- Hellen T.K, "On the method of virtual crack extension", International Journal for Numerical methods in Engineering, 9, pp.187~207 (1975)
- Qian W, "A frictional interfacial crack under combined shear and compression", Composites Science and Technology, 58, pp.1753~1761 (1998)
- Russell A.J, "Moisture and temperature effects on the mixed-mode delamination fracture of unidirectional graphite", epoxy, 1985, pp.876, 349~370
- Carlsson L.A, "On the analysis and design of the end notched flexure (ENF) specimen for mode II testing", Journal of Composite Materials, 20, pp.594~604 (1986)