복합재 접착 체결 구조의 접착 상태가 모드 I 균열 성장 특성에 미치는 영향에 대한 연구
A Study on the Effect of Adhesion Condition on the Mode I Crack Growth Characteristics of Adhesively Bonded Composites Joints
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
본 논문에서는 불균일한 접착 상태를 가지는 복합재 접착 체결 시편에 대하여 모드 I 하중에서의 파괴 특성을 분석하였다. 이를 위하여 Double Cantilever Beam(DCB) 시험을 수행하였으며 모드 I 파괴 인성을 도출하였다. 불균일한 접착 상태를 갖는 시편의 경우 안정한 균열 성장 구간과 불안정한 균열 성장 구간이 나타남을 확인하였다. DCB 시험에서 구한 하중-변위 선도와 시편의 파손 단면을 통해 각 구간의 파괴 특성을 관찰하였다. 시험에서 측정된 균열 길이를 기준으로 세분화된 구간과 각 구간의 모드 I 파괴 인성을 이용하여 유한요소해석을 수행하였다. DCB 시험 결과와 유한요소해석 결과를 통해 불균일한 접착 상태를 가지는 시편의 파괴 거동을 모사 할 수 있음을 확인하였다.
Abstract
In this paper, the characteristics of fracture in mode I loading were analyzed for adhesively bonded joints with non-uniform adhesion. The Double Cantilever Beam test was performed and mode I fracture toughness was obtained. In the case of non-uniform adhesively bonded joints, the stable crack growth sections and unstable crack growth section were shown. The fracture characteristics of each section were observed through the load-displacement curve of the DCB test and the fracture surface of the specimen. Finite Element Analysis was performed at the section based on segmented section by crack length measured through the test and using the mode I fracture toughness of each section. Through DCB test results and finite element analysis results, it was confirmed that the fracture behavior of specimens with non-uniform adhesion can be simulated.
참고문헌 (14)
- 김중진, "복합재-알루미늄 단일겹침 하이브리드 체결부 강도 특성 실험 연구", 한국항공우주학회지, 36(9), pp.841~850 (2008), 한국항공우주학회
- 김원석, "복합재료", 금속 접착 계면의 파괴인성치 측정, 2008, pp.21(4), 7~14[DOI]
- "ASTM D5528, Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites", ~ (2013)
- Mohapatra, P. C., "Effect of Bond Quality on Crack Growth Resistance of Adhesively Bonded Composite Joints under Static and Cyclic Loading", Proceeding of Society for the Advancement of Material and Process Engineering (2017)
- Markatos, D. N., "The Effects of Manufacturing-Induced and In-Service Related Bonding Quality Reduction on the Mode-I Fracture Toughness of Composite Bonded Joints for Aeronautical Use", Composites Part B : Engineering, 45(1), pp.556~564 (2013)
- Sànchez, S., "Analyses of Different Adhesives on Pure Mode I and Mode II Delamination Growth of Composites Bonded Joints", Multidisciplinary Digital Publishing Institute Proceedings, pp.1419~ (2018)
- Mohan, J., "Mode I Fracture Toughness Co-cured and Secondary Bonded Composites Joints", International Journal of Adhesion and Adhesives, 51, pp.13~22 (2014)
- Quan, D., "The Enhancement of Adhesively-bonded Aerospace-grade Composite Joints Using Steel Fibres", Composite Structures, 198, pp.11~18 (2018)
- Floros, I. S., "Mode-I, Mode-II and Mixed-Mode I+II Fracture Behavior of Composite Bonded Joints : Experimental Characterization and Numerical Simulation", Composites Part B : Engineering, 78(29), pp.459~468 (2015)
- 이병언, "응집영역모델을 이용한 섬유금속적층판 접착층의 모드 I, II 파괴 거동 물성평가", Composites Research, 29(2), pp.45~52 (2016), 한국복합재료학회
- Noorman, D.C, "Cohesive Zone Modelling in Adhesively Bonded Joints: Analysis on Crack Propagation in Adhesives and Adherends", Master, pp.2014
- "ASTM D3039, Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials", ~ (2017)
- "ASTM D3518, Standard Test Method for In-Plane Shear Response of Polymer Matrix Composite Materials by Tensile Test of a ±45° Laminate", ~ (2018)
- "ASTM D7905, Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites"