Investigation of Tensile Behaviors in Open Hole and Bolt Joint Configurations of Carbon Fiber/Epoxy Composites
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
This study investigated the open hole tensile (OHT) properties of carbon fiber/epoxy composites and compared them to bolt joint tensile (BJT) properties. The net nominal modulus and strength (1376 MPa) were found to be higher than the gross nominal strength (1041 MPa), likely due to increasing hole size. The OHT and BJT specimens exhibited similar stiffness, as expected without bolt rotation causing secondary bending. OHT specimens experienced a sharp drop in stress indicating unstable crack propagation, delamination, and catastrophic failure. BJT specimens failed through shear out on the bolt side and bearing failure on the nut side, involving fiber kinking, matrix splitting, and delamination, resulting in lower strength compared to OHT specimens. The strength retention of carbon fiber/epoxy composites with open holes was 66%. Delamination initiation at the hole's edge caused a reduction in the stress concentration factor. Filling the hole with a bolt suppressed this relieving mechanism, leading to lower strength in BJT specimens compared to OHT specimens. Bolt joint efficiency was calculated as 15%. The reduction in strength in bolted joints was attributed to fiber⁃matrix splitting and delamination, aligning with Hart Smith's bolted joint efficiency diagram. These findings contribute to materials selection and structural reliability estimation for carbon fiber/epoxy composites. They highlight the behavior of open hole and bolt joint configurations under tensile loading, providing valuable insights for engineering applications.
Abstract
This study investigated the open hole tensile (OHT) properties of carbon fiber/epoxy composites and compared them to bolt joint tensile (BJT) properties. The net nominal modulus and strength (1376 MPa) were found to be higher than the gross nominal strength (1041 MPa), likely due to increasing hole size. The OHT and BJT specimens exhibited similar stiffness, as expected without bolt rotation causing secondary bending. OHT specimens experienced a sharp drop in stress indicating unstable crack propagation, delamination, and catastrophic failure. BJT specimens failed through shear out on the bolt side and bearing failure on the nut side, involving fiber kinking, matrix splitting, and delamination, resulting in lower strength compared to OHT specimens. The strength retention of carbon fiber/epoxy composites with open holes was 66%. Delamination initiation at the hole's edge caused a reduction in the stress concentration factor. Filling the hole with a bolt suppressed this relieving mechanism, leading to lower strength in BJT specimens compared to OHT specimens. Bolt joint efficiency was calculated as 15%. The reduction in strength in bolted joints was attributed to fiber⁃matrix splitting and delamination, aligning with Hart Smith's bolted joint efficiency diagram. These findings contribute to materials selection and structural reliability estimation for carbon fiber/epoxy composites. They highlight the behavior of open hole and bolt joint configurations under tensile loading, providing valuable insights for engineering applications.
참고문헌 (18)
- James Holbery, "Natural-fiber-reinforced polymer composites in automotive applications", JOM, 58(11), pp.80~86 (2006), Springer Science and Business Media LLC[DOI]
- Yang Hua, "Low Friction Coefficient Property of Super Fiber-Reinforced Composites", Advanced Composite Materials, 20(2), pp.133~147 (2011), Informa UK Limited[DOI]
- Sanjay Kumar, "Pin hole tensile and fatigue properties of self-reinforced PET composites", Composite Structures, 255, pp.112981~ (2021), Elsevier BV[DOI]
- Sanjay Kumar, "Strain concentration of double-edge hole ductile composites in the full range of deformation by digital image correlation", Express Polymer Letters, 16(10), pp.1038~1051 (2022), Department of Polymer Engineering, Scientific Society of Mechanical Engineering[DOI]
- Hwang, D. W., "Evaluation of the Bending Strength of Preloaded CF", PEKK at High Temperature, 2023, pp.37(18), 2340028~
- Li, X., "Reinforcing Effects of Gypsum Composite with Basalt Fiber and Diatomite for Improvement of High-temperature Endurance", Construction and Building Materials, 325, pp.126762~ (2022)
- Wu, C. M., "Long-term Open-hole Tensile Creep Properties of Self-reinforced PET Composites Measured by Digital Image Correlation", Materials Chemistry and Physics, 278, pp.125633~ (2022)
- Alaattin Aktaş, "Sea water effect on pinned-joint glass fibre composite materials", Composite Structures, 85(1), pp.59~63 (2008), Elsevier BV[DOI]
- Chang-Mou Wu, "Strain and stress concentration of ductile composites in full-range deformation by digital image correlation", Mechanics of Advanced Materials and Structures, 30(18), pp.3817~3825 (2022), Informa UK Limited[DOI]
- H. Ahmad, "Strength prediction in CFRP woven laminate bolted single-lap joints under quasi-static loading using XFEM", Composites Part A: Applied Science and Manufacturing, 66, pp.82~93 (2014), Elsevier BV[DOI]
- S.R. Hallett, "An experimental and numerical investigation into the damage mechanisms in notched composites", Composites Part A: Applied Science and Manufacturing, 40(5), pp.613~624 (2009), Elsevier BV[DOI]
- "D. ASTM, 5766. Standard Test Method for Open-Hole Tensile Strength of Polymer Matrix Composite Laminates", ~ (2011)
- Gamdani, F., "Tensile Strength of Open-hole, Pin-loaded and Multi-bolted Single-lap Joints in Woven Composite Plates", Materials & Design, 88, pp.702~712 (2015)
- Standard Methods for open Hole Tension Testing of Textile Composites, "Portanova, M. A.", ~ (1995)
- Yan, Y., "Experimental Study on Clamping Effects on the Tensile Strength of Composite Plates with a Bolt-filled Hole", Composites Part A: Applied Science and Manufacturing, 30, pp.1215~1229 (1999)
- Hart-Smith, L. J., "Bolted Joint Analyses for Composite Structures--Current Empirical Methods and Future Scientific Prospects" (2004), ASTM International
- Yudhanto, A., "The Effects of Stitch Orientation on the Tensile and open Hole Tension Properties of Carbon", epoxy Plain Weave Laminates, 2012, pp.35, 563~571
- Wu, C. -M., "Mechanical and open Hole Tensile Properties of Self‐reinforced PET Composites with Recycled PET Fiber Reinforcement", Journal of Applied Polymer Science, 133(29) (2016)