점진적 파손해석을 이용한 탄소섬유강화 복합재료 볼트 조인트의 파손거동 예측
Prediction of Failure Behavior for Carbon Fiber Reinforced Composite Bolted Joints using Progressive Failure Analysis
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
복합재료를 활용하여 설계되는 구조물은 각 부품들의 조립, 체결부를 갖게 된다. 이러한 연결 또는 조인트는 구조에서 잠재적으로 취약 부분이 될 수 있다. 복합재료 볼트 조인트의 파손모드는 구조 안전성을 위해 베어링 파손모드로 설계된다. 베어링 파손모드로 파괴되는 복합재료 볼트 조인트의 하중-변위 관계는 초기 파손 발생 후 비선형 거동을 보이며, 점진적인 파손을 보인다. 이러한 비선형적이고 점진적인 복합재료 볼트 조인트의 파손거동을 정확히 예측하기 위해 본 연구에서는 기존의 파손해석 모델에서 전단 손상변수 계산 과정에 수정을 수행하였다. 수정된 파손해석 모델을 이용하여 복합재료 볼트 조인트의 베어링 응력-베어링 변형률 결과를 예측하였으며, 기존 수정되지 않은 해석모델과 비교를 통해 수정된 모델의 유효성을 입증하였다.
Abstract
Composite structures have components and joints. Theses connections or joints can be potentially weak points in the structure. The failure mode of the composite bolted joint is designed as a bearing failure mode for structural safety. The load-displacement relation exhibits bearing failure mode shows a nonlinear behavior after the initial failure and progressive failure behavior. In order to accurately predict the failure behavior of composite bolted joints, this study modified the shear damage variable calculation process in the existing progressive failure analysis model. The results of the bearing stress-bearing strain of the composite bolted joint were predicted using the modified progressive failure analysis model, and the modified model was verified through comparison with the previous progressive analysis model.
참고문헌 (26)
- Dutton, S., "Composite Materials for Aircraft Structures" (2004), American Institute of Aeronautics and Astronautics
- Hundley, J. M., "Three-dimensional Progressive Failure Analysis of Bolted Titanium-graphite Fiber Metal Laminate Joints", Journal of Composite Materials, 45(7), pp.751~769 (2011)
- 정강우, "원공공차를 가진 볼트 조인트와 핀 조인트의 강도평가에 관한 연구", Composites Research, 25(6), pp.186~190 (2012), 한국복합재료학회
- 피준우, "선박용 복합재 에어 스포일러의 체결부 설계 및 강도 평가", Composites Research, 28(4), pp.219~225 (2015), 한국복합재료학회
- "ASTM D5961", D5961M-13, Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates, 2013, pp.1~31
- Lapczyk, I., "Progressive Damage Modeling in Fiber-reinforced Materials", Composites Part A : Applied Science and Manufacturing, 38(11), pp.2333~2341 (2007)
- Riccio, A., "Intra-laminar Progressive Failure Analysis of Composite Laminates with a Large Notch Damage", Engineering Failure Analysis, 73, pp.97~112 (2017)
- Matzenmiller, A., "A Constitutive Model for Anisotropic Damage in Fiber-composites", Mechanics of Materials, 20(2), pp.125~152 (1995)
- Linde, P., "Modelling of Inter-rivet Buckling of Hybrid Composites", Composite Structures, 73(2), pp.221~228 (2006)
- Hashin, Z., "Failure Criteria for Unidirectional Fiber Composites", Journal of Applied Mechanics, 47(2), pp.329~334 (1980)
- Tikarrouchine, E., "Three-dimensional FE2Method for the Simulation of Non-linear, Rate-dependent Response of Composite Structures", Composite Structures, 193, pp.165~179 (2018)
- Nikbakht, M., "Experimental Validation of an Empirical Nonlinear Shear Failure Model for Laminated Composite Materials", Journal of Composite Materials, 51(16), pp.2331~2345 (2017)
- 이치승, "Puck 파손기준-손상역학 연계이론을 활용한 적층 복합재료의 점진적 파손해석기법 개발", 대한조선학회 논문집, 52(1), pp.52~60 (2015), 대한조선학회
- Kodagali, K., "Progressive Failure Analysis of Composite Materials using the Puck Failure Criteria", Doctoral, pp.2017
- "ASTM D3039", D3039M-14, Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, 2014, pp.1~13
- "ASTM D3410", D3410M-16, Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading, 2016, pp.1~16
- "ASTM D5379", D5379M-12, Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method, 2012, pp.1~14
- "ASTM Standard D5528-13, Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-reinforced Polymer Matrix Composites", ASTM International, 1~13 (2013)
- "ASTM Standard D7905", D7905M-13, Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-reinforced Polymer Matrix Composites, 2013, pp.1~18
- Pinho, S. T., "Fracture Toughness of the Tensile and Compressive Fibre Failure Modes in Laminated Composites", Composites Science and Technology, 66(13), pp.2069~2079 (2006)
- Laffan, M. J., "Measurement of the in situ Ply Fracture Toughness Associated with Mode I Fibre Tensile Failure in FRP. Part I : Data Reduction", Composites Science and Technology, 70(4), pp.606~613 (2010)
- Laffan, M. J., "Measurement of the in situ Ply Fracture Toughness Associated with Mode I Fibre Tensile Failure in FRP. Part II : Size and Lay-up Effects", Composites Science and Technology, 70(4), pp.614~621 (2010)
- Cann, M. T., "Characterization of Fiber Volume Fraction Gradients in Composite Laminates", Journal of Composite Materials, 42(5), pp.447~466 (2008)
- 강민송, "섬유체적비 불균일 및 수지응집층이 복합재 격자 구조체 리브의강성도 거동에 미치는 영향", Composites Research, 31(4), pp.161~170 (2018), 한국복합재료학회
- Shigley, J. E., "Shigley’s Mechanical Engineering Design, Vol. 8" (2008), McGraw-Hill
- Herrington, P. D., "Factors Affecting the Friction Coefficients between Metallic Washers and Composite Surfaces", Composites, 22(6), pp.418~424 (1991)