철계 비동일분율 고엔트로피 합금의 인장 강도에 미치는 소결 조건 영향
Effect of Sintering Condition on Tensile Strength of Fe-based Non-equiatomic High Entropy Alloy
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
We fabricate the non-equiatomic high-entropy alloy (NE-HEA) Fe49.5Mn30Co10Cr10C0.5 (at.%) using spark plasma sintering under various sintering conditions. Each elemental pure powder is milled by high-energy ball milling to prepare NE-HEA powder. The microstructure and mechanical properties of the sintered samples are investigated using various methods. We use the X-ray diffraction (XRD) method to investigate the microstructural characteristics. Quantitative phase analysis is performed by direct comparison of the XRD results. A tensile test is used to compare the mechanical properties of small samples. Next, electron backscatter diffraction analysis is performed to analyze the phase fraction, and the results are compared to those of XRD analysis. By combining different sintering durations and temperature conditions, we attempt to identify suitable spark plasma sintering conditions that yield mechanical properties comparable with previously reported values. The samples sintered at 900 and 1000oC with no holding time have a tensile strength of over 1000 MPa.
Abstract
We fabricate the non-equiatomic high-entropy alloy (NE-HEA) Fe49.5Mn30Co10Cr10C0.5 (at.%) using spark plasma sintering under various sintering conditions. Each elemental pure powder is milled by high-energy ball milling to prepare NE-HEA powder. The microstructure and mechanical properties of the sintered samples are investigated using various methods. We use the X-ray diffraction (XRD) method to investigate the microstructural characteristics. Quantitative phase analysis is performed by direct comparison of the XRD results. A tensile test is used to compare the mechanical properties of small samples. Next, electron backscatter diffraction analysis is performed to analyze the phase fraction, and the results are compared to those of XRD analysis. By combining different sintering durations and temperature conditions, we attempt to identify suitable spark plasma sintering conditions that yield mechanical properties comparable with previously reported values. The samples sintered at 900 and 1000oC with no holding time have a tensile strength of over 1000 MPa.
참고문헌 (26)
- J. W. Yeh, , JOM, 65, pp.1759~ (2013)
- D. B. Miracle, , Acta Mater, 122, pp.448~ (2017)
- Z. Li, , Sci. Rep, 7, pp.40704~ (2017)
- Z. Li, , JOM, 69, pp.2099~ (2017)
- A. K. Maurya, "Correlation of Sintering Parameters with Density and Hardness of Nano-sized Titanium Nitride reinforced Titanium Alloys using Neural Networks", 한국분말재료학회지, 27(5), pp.365~372 (2020), 한국분말재료학회
- 전종규, "분말야금법을 활용한 나노 하이브리드 구조 철-망간계 분말야금재 제조", 한국분말재료학회지, 27(3), pp.203~209 (2020), 한국분말재료학회
- 김유영, "저합금강 소결체의 미세조직 및 기계적 특성에 미치는 인(P) 첨가의 영향", 한국분말재료학회지, 27(1), pp.31~36 (2020), 한국분말재료학회[DOI]
- N. Chawake, , Scr. Mater, 191, pp.46~ (2021)
- R. Shashanka, , Arch. Metall. Mater, 65, pp.5~ (2020)
- C. Suryanarayana, , Prog. Mater. Sci, 46, pp.1~ (2001)
- N. Seo, , Arch. Metall. Mater, 65, pp.1005~ (2020)
- J. Jeon, , Arch. Metall. Mater, 65, pp.1249~ (2020)
- 서남혁, "밀링 조건이 고엔트로피 합금의 미세조직 및 기계적 특성에 미치는 영향", 한국분말재료학회지, 28(2), pp.103~109 (2021), 한국분말재료학회
- Z. Wang, , J. Alloys Compd, 781, pp.734~ (2019)
- J. Su, , Acta Mater, 163, pp.40~ (2019)
- J. Su, , Acta Mater, 167, pp.23~ (2019)
- C. Capdevial, , Mater. Trans, 45, pp.2678~ (2004)
- S. J. Lee, , Mater. Sci. Forum, 475-479, pp.3169~ (2005)
- S. J. Lee, , Metall. Mater. Trans. A, 44, pp.3423~ (2013)
- 오승진, "나노결정 FeMnNiC합금의 오스테나이트 안정성", 한국분말재료학회지, 26(5), pp.389~394 (2019), 한국분말재료학회[DOI]
- S. J. Lee, , Int. J. Mater. Res, 104, pp.423~ (2013)
- S. J. Oh, , Mater. Sci. Eng. A, 725, pp.382~ (2018)
- S. J. Lee, , Metall. Mater. Trans. A, 44, pp.2455~ (2013)
- 최승규, "철계 소결합금의 오스테나이트 안정성", 한국분말재료학회지, 27(5), pp.414~419 (2020), 한국분말재료학회
- S. Choi, , Arch. Metall. Mater, 65, pp.1001~ (2020)
- T. Hanamura, , ISIJ Int, 53, pp.2218~ (2013)