Improvement of Lubrication Characteristics in Fuel Injection Pump for Medium-Speed Diesel Engines: Part I - Application of Profile Shape
2
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
In this research, effects of profile changes of stem section of the plunger on the lubrication characteristics of a fuel injection pump (FIP) were evaluated by hydrodynamic lubrication analysis. The clearance between plunger and barrel was divided into two regions, head and stem. The head was not involved in preventing a decrease of fuel oil pressure. So, research efforts were focused on both edges of the plunger’s stem. The two -dimensional Reynolds equation was used to evaluate lubrication characteristics with variations in viscosity, clearance and profile for a laminar, incompressible, unsteady-state flow. Moreover, the equilibrium equation of moment and forces in the vertical and horizontal directions were used to determine the motion of the plunger. The equations were discretized using the finite difference method. Lubrication characteristics of the FIP were investigated by comparing the dimensionless minimum film thickness, or film parameter, which is the ratio of minimum film thickness to surface roughness. Through numerical analyses, it is found that the profile of the lower edge of the stem had no effect on lubrication characteristics, but the profile of the upper edge had a significant influence on lubrication characteristics. In addition, changes in the profile were more effective in improving lubrication characteristics under low viscosity conditions.
Abstract
In this research, effects of profile changes of stem section of the plunger on the lubrication characteristics of a fuel injection pump (FIP) were evaluated by hydrodynamic lubrication analysis. The clearance between plunger and barrel was divided into two regions, head and stem. The head was not involved in preventing a decrease of fuel oil pressure. So, research efforts were focused on both edges of the plunger’s stem. The two -dimensional Reynolds equation was used to evaluate lubrication characteristics with variations in viscosity, clearance and profile for a laminar, incompressible, unsteady-state flow. Moreover, the equilibrium equation of moment and forces in the vertical and horizontal directions were used to determine the motion of the plunger. The equations were discretized using the finite difference method. Lubrication characteristics of the FIP were investigated by comparing the dimensionless minimum film thickness, or film parameter, which is the ratio of minimum film thickness to surface roughness. Through numerical analyses, we showed that the profile of the lower edge of the stem had no effect on lubrication characteristics, but the profile of the upper edge had a significant influence on lubrication characteristics. In addition, changes in the profile were more effective in improving lubrication characteristics under low viscosity conditions.
참고문헌 (18)
- Park, T. Y., "A Study on the Design Improvement to Increase Durability of Fuel Injection Nozzle for HiMSEN", Journal of Korean Society of Marine Engineering Autumn Conference, pp.231~232 (2010)
- 양영준, "선박 중형디젤엔진용 연료분사펌프 해석 연구", 한국기계가공학회지, 11(6), pp.123~129 (2012), 한국기계가공학회
- Jeon, H. J., "Marine Diesel Engines and Gas Turbines", pp.728~729 (2012), Dong Myeong Publishers
- 홍성호, "연료분사펌프의 최적 간극 설계", 한국윤활학회지, 31(4), pp.148~156 (2015), 한국윤활학회[DOI]
- Lee, B. R., "Hydrodynamic Lubrication Analysis of Plunger Motion for Reciprocating Pump", Proc. Autumn Conference of the KSTLE, pp.255~ (2014)
- Lee, B. R., "Numerical Analysis of the Plunger Motion in Reciprocating Pump", Proc. Spring Conference of the KSTLE, pp.31~32 (2013)
- Lee, B. R., "The Effect of Partial Groove on Lubrication Property for Plunger Pump", Journal of the Korean Soc. Precis. Eng., Spring Conference, pp.564~ (2014)
- Heydari, M., "The Influence of Axial Profile on Pressure Distribution in Radially Loaded Roller", J. of Mech. Eng. Sci, 21, pp.381~388 (1979)
- Rahnejat, H., "Design of Profiled Taper Roller Bearing", Tribology International, 12, pp.269~275 (1979)
- Fujiwara, H., "Logarithmic Profile of Rollers in Roller Bearing and Optimization of the Profile", Trans. of JSME(Part C), 72, pp.3022~3029 (2006)
- Jang, S. Y., "A Study on the Elastohydrodynamic Lubrication of Roller Contact according to Axial Profile", J. Korean Soc. Tribol. Lubr. Eng, 23(5), pp.187~194 (2007)
- 조용주, "Tilting을 고려한 테이퍼롤러 베어링의 최적 크라우닝량 계산", 한국윤활학회지, 25(6), pp.427~431 (2009), 한국윤활학회
- 박태조, "프로파일링한 테이퍼 로울러의 탄성유체윤활 해석", 한국윤활학회지, 28(4), pp.153~159 (2012), 한국윤활학회
- 박태조, "Lundberg형 프로파일의 원통형 로울러의 탄성유체윤활 해석", 한국윤활학회지, 29(6), pp.353~359 (2013), 한국윤활학회[DOI]
- Park, T. J., "EHL Analysis of a Tapered roller with Asymmetric Axial Profile", Proc. Spring Conference of the KSTLE, pp.63~64 (2014)
- Borghi, M., "Hydraulic Locking-in Balancing Grooves", Proc Instn Mech Engrs, 215, pp.157~168 (2001)
- Son, S. I., "The Effect of Piston Profile on the Lubrication Characteristics of a Piston-Type Compressor", Proc. Spring Conference of the KSTLE, pp.45~46 (2011)
- 김동욱, "코닝 조합이 물결 프로파일이 가공된 미케니컬 페이스 실의 작동 성능에 미치는 영향", 한국윤활학회지, 28(2), pp.70~80 (2012), 한국윤활학회[DOI]