박용엔진 크랭크 핀 베어링의 형상오차가 최소유막두께에 미치는 영향
Effect of Roundness Error of a Crank Pin Bearing for a Marine Engine on the Minimum Film Thickness
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Bearings of marine engines are operated under severe conditions because of dynamic load and low sliding speed. This paper deals with lubrication analysis of a crank pin bearing for a marine diesel engine. Journal center locus and oil film thickness are compared of crank pin bearing. In the past researches, journal bearings have been studied only about the surface of bearing. In addition to this conventional research, this paper analyzes the effect of roundness error of a journal and a bearing on the minimum film thickness. Numerical analysis has been studied by using Reynolds equation and also Half-Sommerfeld condition is applied as boundary condition. Futhermore, this study investigates the effect of roundness error change on the minimum film thickness. The results demonstrate that the bigger amplitude of roundness error yields, the lower minimum oil film thickness is. In comparison to previous research considered a journal and a bearing individually, the results considering a journal and a bearing together show that amplitude of roundness error of journal has very little effect on the minimum oil film thickness.
Abstract
Bearings of marine engines are operated under severe conditions because of dynamic load and low sliding speed. This paper deals with lubrication analysis of a crank pin bearing for a marine diesel engine. Journal center locus and oil film thickness are compared of crank pin bearing. In the past researches, journal bearings have been studied only about the surface of bearing. In addition to this conventional research, this paper analyzes the effect of roundness error of a journal and a bearing on the minimum film thickness. Numerical analysis has been studied by using Reynolds equation and also Half-Sommerfeld condition is applied as boundary condition. Futhermore, this study investigates the effect of roundness error change on the minimum film thickness. The results demonstrate that the bigger amplitude of roundness error yields, the lower minimum oil film thickness is. In comparison to previous research considered a journal and a bearing individually, the results considering a journal and a bearing together show that amplitude of roundness error of journal has very little effect on the minimum oil film thickness.
참고문헌 (9)
- Booker, J.F, "Dynamically Loaded Journal Bearings : Mobility Method of Solution", Trans. of the ASME, Journal of Basic Engineering, 87(3), pp.537~546 (1965)
- Booker, J.F, "Dynamically-loaded Journal Bearings : Numerical Application of the Mobility Method", Trans. of the ASME, Journal of Lubrication Technology, (1), pp.168~176 (1971)
- LaBouff, G.A, "Dynamically-loaded Journal Bearings : a Finite Element Treatment for Rigid and Elastic Surfaces", Trans. of the ASME, Journal of Tribology, 107(4), pp.505~515 (1985)
- Oh,K.P, "The Elastohydrodynamic Solution of Journal Bearings under Dynamic Loading", Tran. of the ASME, Journal of Tribology, 107(3), pp.389~395 (1985)
- T.W. Bates, "Oil Film Thickness in an Elastic Connecting Rod Bearing Comparison Between Theory and Experiment", STLE Tribology Transaction, 33 (1990)
- 손상익, "급유홈의 크기와 위치가 원통형 저널 베어링의 정적성능에 미치는 영향", 한국윤활학회지, 26(4), pp.209~218 (2010), 한국윤활학회
- 차지협, "동하중을 받는 박용 디젤 엔진의 저널 베어링 윤활특성에 관한 연구", 한국마린엔지니어링학회 2003년 학술대회 논문집, pp.35~39 (2003)
- 노병후, "유체 윤활 저널 베어링의 소음 예측", 대한기계학회논문집 A, 27(7), pp.1058~1064 (2003), 대한기계학회
- Lubrication Analysis of Marine Engine Bearings, "Yang-Hyup Ha", Pusan National University, ~ (2000)