Aluminium Based Brazing Fillers for High Temperature Electronic Packaging Applications
1
조회
0
다운로드
8
인용
0
참고문헌
키워드
초록
In high temperature aircraft electronics, aluminium based brazing filler is the prime choice today. Aluminium and its alloys have compatible properties like weight minimization, thermal conductivity, heat dissipation, high temperature precipitation hardening etc. suitable for the aerospace industry. However, the selection of brazing filler for high temperature electronics requires high temperature joint strength properties which is crucial for the aerospace. Thus the selection of proper brazing alloy material, the composition and brazing method play an important role in deciding the final reliability of aircraft electronic components. The composition of these aluminium alloys dependent on the addition of the various elements in the aluminium matrix. The complex shapes of aluminium structures like enclosures, heat dissipaters, chassis for electronic circuitry, in avionics are designed from numerous individual components and joined thereafter. In various aircraft applications, the poor strength caused by the casting and shrinkage defects is undesirable. In this report the effect of various additional elements on Al based alloys and brazing fillers have been discussed.
Abstract
In high temperature aircraft electronics, aluminium based brazing filler is the prime choice today. Aluminium and its alloys have compatible properties like weight minimization, thermal conductivity, heat dissipation, high temperature precipitation hardening etc. suitable for the aerospace industry. However, the selection of brazing filler for high temperature electronics requires high temperature joint strength properties which is crucial for the aerospace. Thus the selection of proper brazing alloy material, the composition and brazing method play an important role in deciding the final reliability of aircraft electronic components. The composition of these aluminium alloys dependent on the addition of the various elements in the aluminium matrix. The complex shapes of aluminium structures like enclosures, heat dissipaters, chassis for electronic circuitry, in avionics are designed from numerous individual components and joined thereafter. In various aircraft applications, the poor strength caused by the casting and shrinkage defects is undesirable. In this report the effect of various additional elements on Al based alloys and brazing fillers have been discussed.
참고문헌 (28)
- I. J. Polmear, "Light alloys: From Traditional Alloys to Nanocrystals", pp.16~26 (2006), Elsevier
- B. Altshuller, "Aluminum Brazing Handbook", pp.24~32 (1990), The Aluminum Association, Inc
- A. H. Musfirah, "Magnesium and Aluminum Alloys in Automotive Industry", J. Appl. Sci. Res, 8, pp.4865~ (2012)
- F. Stadler, "Effect of Main Alloying Elements on Strength of Al-Si Foundry Alloys at Elevated Temperatures", Int. J. Cast Metal. Res, 25, pp.215~ (2012)
- C. J. Hang, "Growth Behavior of Cu", Al Intermetallic Compounds and Cracks in Copper Ball Bonds During Isothermal Aging, 2008, pp.48, 416~
- W. F. Smith, "Principles of Materials Science and Engineering", pp.1~892 (1996), McGraw-Hill, Inc
- M. H. Larsen, "Intergranular Corrosion of Copper-Containing AA6xxx AlMgSi Aluminium Alloys", J. Electrochem. Soc, 155(11), pp.C550~ (2008)
- K. Thulukkanam, "Heat Exchanger Design Handbook", pp.996~1002 (2013), CRC Press
- L. C. Tsao, "Brazeability of a 3003 Aluminum alloy with Al-SiCu-based filler metals", J. Mater. Eng. Perform, 11, pp.360~ (2002)
- J. R. Davis, "ASM Specialty Handbook", pp.3~12 (1993), ASM International
- I. J. Polmear, "Metallurgy of the Light Metals", pp.1~288 (1982), E Arnold
- I. J. Polmear, "A Century of Age Hardening", Mater. Forum, 28, pp.1~ (2004)
- E. Romhanji, "Problems and Prospect of Al- Mg Alloy Applications in Marine Constructions, Association of Metallurgical Engineers of Serbia", Metallurgija-Journal of Metallurgy, 12, pp.297~ (2006)
- F. Stadler, "The Effect of Main Alloying Elements on the Physical Properties of Al-Si Foundry Alloys", Mat. Sci. Eng. A, 560, pp.481~ (2013)
- Effects of Additives on the Microstructures and Tensile Properties of a New Al-Cu Based Alloy Intended For Automotive Castings, "E. M. Elgallad", AFS Transactions, 1~24, pp.American Foundary Society, Paper 10-042 (2010)
- M. Jaradeh, "Effect of Titanium Additions on the Microstructure of DC-Cast Aluminium Alloys", Mat. Sci. Eng. A, 413-414, pp.277~ (2005)
- Y. Birol, "A Novel Al-Ti-B Alloy For Grain Refining Al-Si Foundry Alloys", J. Alloy. Compd, 486, pp.219~ (2009)
- T. N. Ware, "Effect of Sr, Na, Ca & P on the Castability of Foundry Alloy A356.2", ASM Materials Solutions Conference & Exposition, Proc. 2nd International Aluminium Casting Technology Symposium (IACTS) (2002)
- S. W. Nam, "The Effect of Mn on the Mechanical Behavior of Al Alloys", Metals and Materials, 6(1), pp.13~ (2000)
- A. Darvishi, "The Mutual Effect of Iron and Manganese on Microstructure and Mechanical properties of Aluminium-Silicon Alloy", Association of Metallurgical Engineers of Serbia, MJoM, 16(1), pp.11~ (2010)
- T. O. Mbuyaa, "Influence of Iron on Castability and Properties of Aluminium Silicon Alloys: Literature Review", Int. J. Cast Metal Res, 15, pp.451~ (2003)
- N. L. Sukiman, "Property Space, Techniques and Developments", pp.47~97 (2012), InTech
- Z. Nie, "Research on Rare Earth in Aluminum", Mater. Sci. Forum, 396-402, pp.1731~ (2002)
- K. Nogita, "Eutectic Modification of Al-Si Alloys with Rare Earth Metals", Mater. Trans, 45(2), pp.323~ (2004)
- H. F. El-Labban, "Preparation and Characterization of Squeeze Cast-Al-Si Piston Alloy Reinforced by Ni and Nano-Al2O3 Particles", J. King Saud Univ. Eng. Sci., in press (2014)
- Hongseok Choi, "Refinement of Primary Si and Modification of Eutectic Si for Enhanced Ductility of Hypereutectic Al-20Si-4.5Cu Alloy with Addition of Al2O3 Nanoparticles", J. Mater. Sci, 47, pp.3096~ (2012)
- A. Sharma, "Development of Lead Free Pulse Electrodeposited Tin Based Composite Solder Coating Reinforced with ex-situ Cerium Oxide Nanoparticles", J. Alloy. Compd, 574, pp.609~ (2013)
- A. Sharma, "Fabrication of Sn-Ag", CeO2 Electro-Composite Solder by Pulse Electrodeposition, 2013, pp.44A, 5587~