Advanced Powder Processing Techniques of Ti Alloy Powders for Medical and Aerospace Applications
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
In this paper, two kinds of advanced powder processing techniques Metal Injection Molding (MIM) and Direct Laser Forming (DLF) are introduced to fabricate complex shaped Ti alloy parts which are widely used for medical and aerospace applications. The MIM process is used to strengthen Ti-6Al-4V alloy compacts by addition of fine Mo, Fe or Cr powders. Enhanced tensile strength of 1030 MPa with 15.1% elongation was obtained by an addition of 4 mass%Cr because of the microstructural modification and also the solution strengthening in beta phase. However, their fatigue strength was lower compared to wrought materials, but was improved by HIP. Subsequently, the effect of feeding layer height (FLH) on the characteristics of the DLF compacts was investigated. In the case of 100 μm FLH, surface roughness was improved and nearly full density (99.8%) was obtained. Also, tensile strength of 1080 MPa was obtained, which is higher than the ASTM value.
Abstract
In this paper, two kinds of advanced powder processing techniques Metal Injection Molding (MIM) and Direct Laser Forming (DLF) are introduced to fabricate complex shaped Ti alloy parts which are widely used for medical and aerospace applications. The MIM process is used to strengthen Ti-6Al-4V alloy compacts by addition of fine Mo, Fe or Cr powders. Enhanced tensile strength of 1030 MPa with 15.1% elongation was obtained by an addition of 4 mass%Cr because of the microstructural modification and also the solution strengthening in beta phase. However, their fatigue strength was lower compared to wrought materials, but was improved by HIP. Subsequently, the effect of feeding layer height (FLH) on the characteristics of the DLF compacts was investigated. In the case of 100 μm FLH, surface roughness was improved and nearly full density (99.8%) was obtained. Also, tensile strength of 1080 MPa was obtained, which is higher than the ASTM value.
참고문헌 (15)
- Y. Itoh., , 2004 Powder Metallurgy World Congress, 4, pp.445~ (2004)
- Y. Itoh., , Journal of the Japan Society of Powder and Powder Metallurgy, 52, pp.43~ (2005)
- Y. Itoh., , Journal of the Japan Society of Powder and Powder Metallurgy, 55, pp.720~ (2008)
- Y. Itoh., , Journal of the Japan Society of Powder and Powder Metallurgy, 53, pp.821~ (2006)
- Y. Itoh., , Ti-2007 Science and Technology, The Japan Institute of Metals, 2, pp.1185~ (2007)
- Y. Itoh., , Journal of the Japan Society of Powder and Powder Metallurgy, 53, pp.750~ (2006)
- R. Boyer., "Materials Properties Handbook : Titanium Alloys" (1994), ASM International
- C. K. Chua., "Rapid Prototyping: Principles and Applications 2nd ed." (2003), World Scientific Publishing
- H. Miura., , Mater. Sci. Forum, 534-536, pp.465~ (2007)
- H. G. Kang., , Adv. Mater. Res., 89-91, pp.281~ (2010)
- H. G. Kang., , Journal of the Japan Society of Powder and Powder Metallurgy, 58, pp.436~ (2011)
- H. Miura., , Mater. Sci. Forum, 654-656, pp.2057~ (2010)
- H. Miura., , Proc. Powder Metallurgy & Particulate Materials (2009)
- Y. Itoh., , Journal of the Japan Society of Powder and Powder Metallurgy, 56, pp.259~ (2009)
- M. Hasegawa., "Stainless steel Handbook" (1973), Nikkan Kogyo Shimbun, Ltd