내부 원추형 연결형태 임플란트에서 지대주 나사머리의 좌면각도가 연결부 기계적 안정성에 미치는 영향
Influence of bearing surface angle of abutment screw on mechanical stability of joint in the conical seal design implant system
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
목적: 내부 원추형 연결형태 임플란트에서 지대주 나사의 좌면각도가 연결부의 기계적 안정성에 미치는 영향을 알아보기 위함이다. 연구 재료 및 방법: 원추형 연결구조 티타늄 임플란트와 시멘트 유지형 지대주, 텅스텐 카바이드 코팅된 티타늄 합금 지대주 나사를 사용하였다. 좌면각도가 45°와 90°를 갖는 지대주와 지대주 나사를 제작하여 30 Ncm 조임회전력으로 지대주를 체결한 후 하중을 가하고 체결 및 하중 부여에 따른 침하량을 측정하였다(n = 5). 유압식 피로시험기에 임플란트를 고정하고 스테인리스 스틸 금속관을 지대주에 합착하였다. 이 후 반복 하중을 가한 후 풀림토크 변화량을 측정하고, 압축굽힘강도와 피로강도를 측정하였다(n = 5). 결과: 지대주 침하량은 지대주나사 체결 시 가장 크게 나타났으며(P < 0.05), 나사체결과 하중부여에 따른 총 침하량은 45°군보다 90°군에서 더 크게 측정되었다(P < 0.05). 반복하중 부여 후 풀림 토크, 그리고 최대 압축굽힘강도와 피로강도는 통계적으로 유의한 차이를 보이지 않았다(P > 0.05). 결론: 본 실험조건하에서 지대주 나사머리의 원추형 설계가 지대주의 총 침하량을 약간 감소시키는 효과를 나타냈으나, 연결부의 전체적인 기계적 안정성에 미치는 영향은 크지 않을 것으로 판단된다.
Abstract
Purpose: This study is to evaluate how different bearing surface angles of abutment screw affect the mechanical stability of the joint in the conical seal design implant system. Materials and Methods: Internal connection type regular implants, two-piece cemented type abutments and tungsten carbide/carbon-coated titanium alloy abutment screws were selected. Titanium alloy screws with conical (45°) and flat (90°) head designs which fit on to abutment were fabricated. The abutments were tightened to implants with 30 Ncm by digital torque gauge. The loading was applied once to the central axis of abutment. The mean axial displacement was measured using micrometer before and after the tightening and loading (n = 5). The abutment was tightened to implants with 30 Ncm and T-shape stainless steel crown was cemented. Then the change in the amount of reverse-torque was measured after the repeated loading to the central axis, and the place 5 mm away from the central axis. Compressive bending and fatigue strength were measured at the place 5 mm away from the central axis (n = 5). Results: Both groups showed the largest axial displacement when abutment screw tightening and total displacement was greater in the flat head group compared to conical head group (P <0.05). However, there were no significant differences in reverse torque value, compressive bending and fatigue strength (P > 0.05). Conclusion: Within the limitations of this study, the abutment screw head design had no effect on two groups regarding the joint stability, however the conical head design affected the settlement of abutment resulting in the reduced total displacement.
참고문헌 (34)
- Brånemark PI, "Intra-osseous anchorage of dental prostheses. I. Experimental studies", Scand J Plast Reconstr Surg, 3, pp.81~100 (1969)
- Brånemark PI, "Osseointegrated implants in the treatment of the edentulous jaw. Experience from a 10-year period", Scand J Plast Reconstr Surg, 16, pp.1~132 (1977)
- Zarb GA, "The longitudinal clinical effectiveness of osseointegrated dental implants: the Toronto study. Part I: surgical results", J Prosthet Dent, 63, pp.451~457 (1990)
- Zarb GA, "The longitudinal clinical effectiveness of osseointegrated dental implants: the Toronto study. Part III: problems and complications encountered", J Prosthet Dent, 64, pp.185~194 (1990)
- Adell R, "A 15-year study of osseointegrated implants in the treatment of edentulous jaw", Int J Oral Surg, 10, pp.387~416 (1981)
- Johansson G, "Complications, supplementary treatment, and maintenance in edentulous arches with implant-supported fixed prostheses", Int J Prosthodont, 3, pp.89~92 (1990)
- Tolman DE, "Tissue-integrated prosthesis complications", Int J Oral Maxillofac Implants, 7, pp.477~484 (1992)
- Carlson B, "Prosthodontic complications in osseointegrated dental implant treatment", Int J Oral Maxillofac Implants, 9, pp.90~94 (1994)
- Hemmings KW, "Complications and maintenance requirements for fixed prostheses and overdentures in the edentulous mandible: a 5-year report", Int J Oral Maxillofac Implants, 9, pp.191~196 (1994)
- Jemt T, "A 3-year follow-up study on single implant treatment", J Dent, 21, pp.203~208 (1993)
- Jörnéus L, "Loads and designs of screw joints for single crowns supported by osseointegrated implants", Int J Oral Maxillofac Implants, 7, pp.353~359 (1992)
- Burguete RL, "Tightening characteristics for screwed joints in osseointegrated dental implants", J Prosthet Dent, 71, pp.592~599 (1994)
- Taylor TD, "Prosthodontic problems and limitations associated with osseointegration", J Prosthet Dent, 79, pp.74~78 (1998)
- Khraisat A, "Stability of the implant", abutment joint in a single-tooth external-hexagon implant system: clinical and mechanical review, 2004, pp.6, 222~229
- Kitagawa T, "Influence of implant", abutment joint designs on abutment screw loosening in a dental implant system, 2005, pp.75, 457~463
- Tsuge T, "Influence of lateral-oblique cyclic loading on abutment screw loosening of internal and external hexagon implants", Dent Mater J, 28, pp.373~381 (2009)
- Khayat PG, "An investigation of 131 consecutively placed wide screw-vent implants", Int J Oral Maxillofac Implants, 16, pp.827~832 (2001)
- Park JK, "Effects of abutment screw coating on implant preload", J Prosthodont, 19, pp.458~464 (2010)
- Binon PP, "Evaluation of three slip fit hexagonal implants", Implant Dent, 5, pp.235~248 (1996)
- Binon PP, "The spline implant: design, engineering, and evaluation", Int J Prosthodont, 9, pp.419~433 (1996)
- Norton MR, "An in vitro evaluation of the strength of an internal conical interface compared to a butt joint interface in implant design", Clin Oral Implants Res, 8, pp.290~298 (1997)
- Bozkaya D, "Mechanics of the taper integrated screwed-in (TIS) abutments used in dental implants", J Biomech, 38, pp.87~97 (2005)
- Bozkaya D, "Mechanics of the tapered interference fit in dental implants", J Biomech, 36, pp.1649~1658 (2003)
- Dailey B, "Axial displacement of abutments into implants and implant replicas, with the tapered cone-screw internal connection, as a function of tightening torque", Int J Oral Maxillofac Implants, 24, pp.251~256 (2009)
- Jemt T, "Prosthesis misfit and marginal bone loss in osseointegrated implant patients", Int J Oral Maxillofac Implants, 11, pp.620~625 (1996)
- Guichet DL, "Passivity of fit and marginal opening in screw- or cement-retained implant fixed partial denture designs", Int J Oral Maxillofac Implants, 15, pp.239~246 (2000)
- Herbst D, "Evaluation of impression accuracy for osseointegrated implant supported superstructures", J Prosthet Dent, 83, pp.555~561 (2000)
- Sahin S, "The significance of passive framework fit in implant prothodontics: current status", Implant Dent, 10, pp.85~92 (2001)
- Ding TA, "Evaluation of the ITI Morse taper implnat", abutment design with an internal modification, 2003, pp.18, 865~872
- Binon PP, "Implants and components: entering the new millennium", Int J Oral Maxillofac Implants, 15, pp.76~94 (2000)
- Dixon DL, "Comparison of screw loosening, rotation, and deflection among three implant designs", J Prosthet Dent, 74, pp.270~278 (1995)
- Gibbs CH, "Occlusal forces during chewing and swallowing as measured by sound transmission", J Prosthet Dent, 46, pp.443~449 (1981)
- Haraldson T, "Bite force and oral function in patients with osseointegrated oral implants", Scand J Dent Res, 85, pp.200~208 (1977)
- Steinebrunner L, "Implant-abutment interface design affects fatigue and fracture strength of implnat", Clin Oral Implants Res, 19, pp.1276~1284 (2008)