용접형 판형열교환기의 유동분배 및 특성에 대한 연구
Study of flow distribution and flow characteristics in the welded plate heat exchanger
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
An experimental study on the flow distribution characteristics according to the inlet direction of the working fluid and an analytical study on the flow characteristics according to the variation of the outlet width were carried out in order to present the optimal design of welded plate heat exchanger. In the experiment results on the flow distribution according to the inflow direction of the working fluid, the flow distribution in the welded plate heat exchanger is mainly formed around the center channel. As the inflow flow rate increases, the flow distribution ratio at the center channel decreases, whereas the flow distribution ratio at the side channel increases, thereby improving the distribution effect. The increase inflow rate of working fluid brings the incre of the pressure drop in the channel while the increase in width at the outlet reduces the pressure drop. Besides, it can be seen the dead zone where the fluid flow stagnates at the opposite corner of the outlet side.
Abstract
An experimental study on the flow distribution characteristics according to the inlet direction of the working fluid and an analytical study on the flow characteristics according to the variation of the outlet width were carried out in order to present the optimal design of welded plate heat exchanger. In the experiment results on the flow distribution according to the inflow direction of the working fluid, the flow distribution in the welded plate heat exchanger is mainly formed around the center channel. As the inflow flow rate increases, the flow distribution ratio at the center channel decreases, whereas the flow distribution ratio at the side channel increases, thereby improving the distribution effect. The increase inflow rate of working fluid brings the incre of the pressure drop in the channel while the increase in width at the outlet reduces the pressure drop. Besides, it can be seen the dead zone where the fluid flow stagnates at the opposite corner of the outlet side.
참고문헌 (12)
- Lee, J., "Friction and Colburn factor correlations and shape optimization of chevron-type plate heat exchangers", Applied Thermal Engineering, 89, pp.62~69 (2015)[DOI]
- A. Muley, "Experimental study of turbulent flow heat transfer and pressure drop in a plate heat exchanger with chevron plates", J. Heat. Transf., 121, pp.110~117 (1999)[DOI]
- M.S. Kim, "Correlations and optimization of a heat exchanger with offset strip fins", Int. J. Heat. Mass Transf., 54, pp.2073~2079 (2011)[DOI]
- Wang, Y. N., "A study on 3D numerical model for plate heat exchanger", Procedia engineering, 174, pp.188~194 (2017)[DOI]
- Zhang, Y., "Numerical study on heat transfer enhancement in capsule-type plate heat exchangers", Applied Thermal Engineering, 108, pp.1237~1242 (2016)[DOI]
- Jin, B. J., "A Study on Forming for Plate-Type Heat Exchangers of the Ti Material", Procedia engineering, 174, pp.171~178 (2017)[DOI]
- Wang, T., "Waste heat recovery through plate heat exchanger based thermoelectric generator system", Applied Energy, 136, pp.860~865 (2014)[DOI]
- Walraven, D., "Comparison of shell-and-tube with plate heat exchangers for the use in low-temperature organic Rankine cycles", Energy Conversion and Management, 87, pp.227~237 (2014)[DOI]
- Jeong, J. Y., "Impact of plate design on the performance of welded type plate heat exchangers for sorption cycles", International journal of refrigeration, 32(4), pp.705~711 (2009)[DOI]
- R. Barzegarian, , Exp. Therm Fluid Sci., 74, pp.11~18 (2016)[DOI]
- A.K. Tiwari, , Appl. Therm. Eng., 57, pp.24~32 (2013)[DOI]
- "ANSYS Fluent Theory Guide, Release 15.0", ~ (2013)