UNS S31603에 대하여 완전요인설계를 이용한 전해연마조건에 따른 표면 거칠기의 유효인자 산출
Identifying Factors Affecting Surface Roughness with Electropolishing Condition Using Full Factorial Design for UNS S31603
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
The objective of this investigation was to indentify major factors affecting surface roughness among various parameters of electropolishing process using the design of an experiment method (full factorial design) for UNS S31603. Factors selected included electrolyte composition ratio, applied current density, and electrolytic polishing time. They were compared through analysis of variance (ANOVA). Results of ANOVA revealed that all parameters could affect surface roughness, with the influence of electrolyte composition ratio being the highest. As a result of surface analysis after electropolishing, the specimen with the deepest surface damage was about 35 times greater than the condition with the smallest surface damage. The largest value of surface roughness after electropolishing was higher than that of mechanical polishing due to excessive processing. On the other hand, the smallest value of surface roughness after electropolishing was 0.159 μm, which was improved by more than 80% compared to the previous mechanical polishing. Taken all results together, it is the most appropriate to perform electrolytic polishing with a sulfuric acid and phosphoric acid ratio of 3:7, an applied current density of 300 mA/cm2, and anelectrolytic polishing time of 5 minutes.
Abstract
The objective of this investigation was to indentify major factors affecting surface roughness among various parameters of electropolishing process using the design of an experiment method (full factorial design) for UNS S31603. Factors selected included electrolyte composition ratio, applied current density, and electrolytic polishing time. They were compared through analysis of variance (ANOVA). Results of ANOVA revealed that all parameters could affect surface roughness, with the influence of electrolyte composition ratio being the highest. As a result of surface analysis after electropolishing, the specimen with the deepest surface damage was about 35 times greater than the condition with the smallest surface damage. The largest value of surface roughness after electropolishing was higher than that of mechanical polishing due to excessive processing. On the other hand, the smallest value of surface roughness after electropolishing was 0.159 μm, which was improved by more than 80% compared to the previous mechanical polishing. Taken all results together, it is the most appropriate to perform electrolytic polishing with a sulfuric acid and phosphoric acid ratio of 3:7, an applied current density of 300 mA/cm2, and anelectrolytic polishing time of 5 minutes.
참고문헌 (30)
- P. S. Maiya, "Effect of surface roughness on low-cycle fatigue behavior of type 304 stainless steel", Metallurgical Transactions A, 6(9), pp.1761~1766 (1975), Springer Science and Business Media LLC[DOI]
- Takeshi Ogawa, "THE EFFECT OF MICROSTRUCTURE AND FRACTURE SURFACE ROUGHNESS ON FATIGUE CRACK PROPAGATION IN A Ti-6A1-4V ALLOY", Fatigue & Fracture of Engineering Materials & Structures, 16(9), pp.973~982 (1993), Wiley[DOI]
- Ian Gibson, "Photopolymerization Processes", Additive Manufacturing Technologies, 4, pp.78~119 (2010), Springer US[DOI]
- Hui Zhao, "Electrochemical polishing of 316L stainless steel slotted tube coronary stents", Journal of Materials Science: Materials in Medicine, 13(10), pp.911~916 (2002), Springer Science and Business Media LLC[DOI]
- 김수한, "반구형 부스바를 이용한 전해연마액 수명연장을 위한 공정 최적화", 한국표면공학회지, 49(5), pp.447~453 (2016), 한국표면공학회[DOI]
- Feroze Nazneen, "Electropolishing of medical-grade stainless steel in preparation for surface nano-texturing", Journal of Solid State Electrochemistry, 16(4), pp.1389~1397 (2012), Springer Science and Business Media LLC[DOI]
- M. Baumers, "The cost of additive manufacturing: machine productivity, economies of scale and technology-push", Technological Forecasting and Social Change, 102, pp.193~ (2016)
- Rainer J. Hebert, "Viewpoint: metallurgical aspects of powder bed metal additive manufacturing", Journal of Materials Science, 51(3), pp.1165~1175 (2015), Springer Science and Business Media LLC[DOI]
- Martin Baumers, "The cost of additive manufacturing: machine productivity, economies of scale and technology-push", Technological Forecasting and Social Change, 102, pp.193~201 (2016), Elsevier BV[DOI]
- S.C. Tam, "Electrochemical polishing of biomedical titanium orifice rings", Journal of Materials Processing Technology, 35(1), pp.83~91 (1992), Elsevier BV[DOI]
- Chi-Cheng Lin, "Electropolishing of 304 stainless steel: Surface roughness control using experimental design strategies and a summarized electropolishing model", Electrochimica Acta, 53(8), pp.3356~3363 (2008), Elsevier BV[DOI]
- D. Landolt, "Fundamental aspects of electropolishing", Electrochimica Acta, 32(1), pp.1~11 (1987), Elsevier BV[DOI]
- D. Brent, "Taguchi Design of Experiment for the Optimization of Electrochemical Polishing of Metal Additive Manufacturing Components", Proceedings of the ASME 2016 International Mechanical Engineering Congress and Exposition, 2, pp.1~ (2017)
- 장재영, "치과 주조용 Co.Cr-Mo alloy에서 전해용액 온도와 전해시간에 따른 전해연마의 특성", 대한치과기공학회지, 34(2), pp.145~153 (2012), 대한치과기공학회[DOI]
- S. H. Kim, "Process Optimization for Life Extension of Electropolishing Solution for Semiconductor Piping Tube", doctor, pp.2016
- K. H. Jung, "Investigation on the Prediction of Electrochemical and Mechanical Characteristics of Stainless Steel for Marine Environments using Machine Learning and Experimental Design", doctor, pp.2020
- G. Taguchi, "Introduction to quality engineering: designing quality into products and processes", pp.191~ (1986), The National Academies of Sciences, Engineering and Medicine
- S. B. Lee, "Minitab example-driven design of experiments", ERETECH, 9~ (2018)
- 남상건, "효과크기의 이해", Hanyang Medical Reviews, 35(1), pp.40~43 (2015), 한양대학교 의과대학[DOI]
- C. Clerc, "On the theory of anodic levelling: model experiments with triangular nickel profiles in chloride solution", Electrochimica Acta, 29(10), pp.1477~1486 (1984), Elsevier BV[DOI]
- E. J. Taylor, "Electrochemical Surface Finishing", Interface magazine, 23(3), pp.57~61 (2014), The Electrochemical Society[DOI]
- Edyta Łyczkowska-Widłak, "Electrochemical Polishing of Austenitic Stainless Steels", Materials, 13(11), pp.2557~ (2020), MDPI AG[DOI]
- Emma L. Smith, "Deep Eutectic Solvents (DESs) and Their Applications", Chemical Reviews, 114(21), pp.11060~11082 (2014), American Chemical Society (ACS)[DOI]
- S. J. Lee, "The Investigation of Surface Morphology Forming Mechanisms in Electropolishing Process", International Journal of Electrochemical Science, 7, pp.12495~ (2012)[DOI]
- M. Datta, "Fundamental aspects and applications of electrochemical microfabrication", Electrochimica Acta, 45(15-16), pp.2535~2558 (2000), Elsevier BV[DOI]
- SoonTaeKim, "Effects of Copper and Sulfur Additions on Corrosion Resistance and Machinability of Austenitic Stainless Steel", CORROSION SCIENCE AND TECHNOLOGY, 31(2), pp.4~128 (2002), 한국부식방식학회
- Yushu Wang, "Corrosion Behavior of Austenitic and Duplex Stainless Steels in Thiosulfate- and Chloride-Containing Environments", CORROSION, 71(8), pp.937~944 (2015), NACE International[DOI]
- 박일초, "양극산화 처리된 5083 알루미늄 합금의 해수 내 유속변화에 따른 전기화학적 손상 특성", 한국표면공학회지, 49(4), pp.349~356 (2016), 한국표면공학회[DOI]
- 황현규, "전해연마 용액에서 안정화 시간과 표면 거칠기에 따른 오스테나이트 스테인리스강의 전기화학적 특성", CORROSION SCIENCE AND TECHNOLOGY, 21(2), pp.158~169 (2022), 한국부식방식학회[DOI]
- 신동호, "고분자 전해질 연료전지 금속분리판용 316L 스테인리스강의 양극작동조건에서 염화물 농도에 따른 부식 특성", CORROSION SCIENCE AND TECHNOLOGY, 20(6), pp.435~450 (2021), 한국부식방식학회[DOI]