본문 바로가기
KERD
논문KCI 등재

전해연마 용액에서 안정화 시간과 표면 거칠기에 따른 오스테나이트 스테인리스강의 전기화학적 특성

Electrochemical Properties of Austenitic Stainless Steel with Initial Delay Time and Surface Roughness in Electropolishing Solution

황현규|김성종
한국재료부식학회 (The Corrosion Science Society of Korea)|2022.04|CORROSION SCIENCE AND TECHNOLOGY|제21권 제2호|pp. 158-169|DOI 10.14773/cst.2022.21.2.158

0

조회

0

다운로드

2

인용

0

참고문헌

키워드

Surface roughnessElectropolishingUNS S31603Initial delay timeSecond anodic peak
주제분류금속공학

초록

The objective of this study was to investigate the electrochemical behavior and damage degree of metalsurface under different conditions by performing a potentiodynamic polarization experiment using an electropolishing solution for UNS S31603 based on initial delay time and surface roughness (parameters). A second anodic peak occurred at initial delay time of 0s and 100s. However, it was not discovered at 1000s and 3600s. This research referred to an increase in current density due to hydrogen oxidation reaction among various hypotheses for the second anodic peak. After the experiment, both critical current density and corrosion current density decreased when the initial delay time (immersion time) was longer. As a result of surface analysis, charact eristics of the potentiodynamic polarization behavior were similar with roughness, although the degree of damage was clearly different. With an increase in surface roughness value, the degree of surface damage was precisely observed. As such, electrochemical properties were different according to the immersion time in the electropolishing solution. To select electropolishing conditions such as applied current density, voltage, and immersion time, 1000s for initial delay time on the potentiodynamic polarization behavior was the most appropriate in this experiment.

Abstract

The objective of this study was to investigate the electrochemical behavior and damage degree of metalsurface under different conditions by performing a potentiodynamic polarization experiment using an electropolishing solution for UNS S31603 based on initial delay time and surface roughness (parameters). A second anodic peak occurred at initial delay time of 0s and 100s. However, it was not discovered at 1000s and 3600s. This research referred to an increase in current density due to hydrogen oxidation reaction among various hypotheses for the second anodic peak. After the experiment, both critical current density and corrosion current density decreased when the initial delay time (immersion time) was longer. As a result of surface analysis, charact eristics of the potentiodynamic polarization behavior were similar with roughness, although the degree of damage was clearly different. With an increase in surface roughness value, the degree of surface damage was precisely observed. As such, electrochemical properties were different according to the immersion time in the electropolishing solution. To select electropolishing conditions such as applied current density, voltage, and immersion time, 1000s for initial delay time on the potentiodynamic polarization behavior was the most appropriate in this experiment.

참고문헌 (34)

  1. 김수한, "산업현장 적용을 위한 스테인레스 스틸의 전해연마 특성", 한국표면공학회지, 49(4), pp.363~367 (2016), 한국표면공학회[DOI]
  2. Feroze Nazneen, "Electropolishing of medical-grade stainless steel in preparation for surface nano-texturing", Journal of Solid State Electrochemistry, 16(4), pp.1389~1397 (2011), Springer Science and Business Media LLC[DOI]
  3. E.-S. Lee, "Machining Characteristics of the Electropolishing of Stainless Steel (STS316L)", The International Journal of Advanced Manufacturing Technology, 16(8), pp.591~599 (2000), Springer Science and Business Media LLC[DOI]
  4. 장재영, "치과 주조용 Co.Cr-Mo alloy에서 전해용액 온도와 전해시간에 따른 전해연마의 특성", 대한치과기공학회지, 34(2), pp.145~153 (2012), 대한치과기공학회[DOI]
  5. Yogesh B. Patil, "A REVIEW ON ELCTROPOLISHING PROCESS AND ITS AFFECTING PARAMETERS", International Journal of Advance Research In Science And Engineering, 3, pp.246~ (2014)
  6. F.A. Arash, "Electrochemical Behaviour of AISI 410 Stainless Steel at Open Circuit Potential in Acidic Solutions", Analytical & Bioanalytical Electrochemistry, 6, pp.284~ (2014)
  7. Shuo-Jen Lee, "The effects of electropolishing (EP) process parameters on corrosion resistance of 316L stainless steel", Journal of Materials Processing Technology, 140(1-3), pp.206~210 (2003), Elsevier BV[DOI]
  8. Mirjam Bajt Leban, "The Effect of Surface Roughness on the Corrosion Properties of Type AISI 304 Stainless Steel in Diluted NaCl and Urban Rain Solution", Journal of Materials Engineering and Performance, 23(5), pp.1695~1702 (2014), Springer Science and Business Media LLC[DOI]
  9. Lisbeth R. Hilbert, "Influence of surface roughness of stainless steel on microbial adhesion and corrosion resistance", International Biodeterioration & Biodegradation, 52(3), pp.175~185 (2003), Elsevier BV[DOI]
  10. Sang Mok Lee, "Surface roughness and the corrosion resistance of 21Cr ferritic stainless steel", Corrosion Science, 63, pp.404~409 (2012), Elsevier BV[DOI]
  11. D. Gopi, "Enhanced corrosion resistance of strontium hydroxyapatite coating on electron beam treated surgical grade stainless steel", Applied Surface Science, 286, pp.83~90 (2013), Elsevier BV[DOI]
  12. G. T. Burstein, "Surface Roughness and the Metastable Pitting of Stainless Steel in Chloride Solutions", CORROSION, 51(5), pp.380~385 (1995), NACE International[DOI]
  13. Herbert H. Uhlig, "Anodic Polarization of Passive and Non-passive Chromium–Iron Alloys.", The Journal of Physical Chemistry, 57(3), pp.280~283 (1953), American Chemical Society (ACS)[DOI]
  14. G.E.C. Bell, "Electrochemical and microstructural characterization of an austenitic stainless steel irradiated by heavy ions at 515 oC", Journal of Nuclear Materials, 187, pp.170~ (1992)
  15. Narayanan Srinivasan, "Anodic Polarization Behavior of Cold Worked Austenitic Stainless Steel", Advanced Materials Research, 794, pp.632~642 (2013), Trans Tech Publications, Ltd.[DOI]
  16. Cheng Man, "A comparative study of primary and secondary passive films formed on AM355 stainless steel in 0.1 M NaOH", Applied Surface Science, 427, pp.763~773 (2018), Elsevier BV[DOI]
  17. P. Radhakrishnamurty, "pH-potential diagrams at elevated temperatures for the chromium", water system, 1982, pp.22(8), 753~773[DOI]
  18. Junbo Huang, "Electrochemical properties and growth mechanism of passive films on Alloy 690 in high-temperature alkaline environments", Corrosion Science, 52(10), pp.3444~3452 (2010), Elsevier BV[DOI]
  19. Iva Betova, "The transpassive dissolution mechanism of highly alloyed stainless steels: I. Experimental results and modelling procedure", Corrosion Science, 44(12), pp.2675~2697 (2002), Elsevier BV[DOI]
  20. Denny A Jones, "Principles and prevention of corrosion", pp.87~ (1995)
  21. M. B. ROCKEL, "Interpretation of the Second Anodic Current Maximum on Polarization Curves of Sensitized Chromium Steels in 1N H2 SO4", Corrosion, 27(3), pp.95~103 (1971), NACE International[DOI]
  22. W. D. FRANCE, "Interpretation of Passive Current Maxima During Polarization of Stainless Steels", Corrosion, 24(12), pp.403~406 (1968), NACE International[DOI]
  23. Kim, C. D., , Proc. NACE Conf (1970)
  24. P. Süry, "Einfluß der Wärmebehandlung auf den Verlauf der Stromdichte-Potential-Kurven bei einem 13%igen Chromstahlguß", Werkstoffe und korrosion, 20(8), pp.665~672 (1969), Wiley[DOI]
  25. Kwang-Hu Jung, "Influence of Sensitization on Mechanical Properties of AISI 304 Stainless Steel under High-Temperature", Journal of Nanoscience and Nanotechnology, 19(7), pp.7598~ (2019), American Scientific Publishers[DOI]
  26. J. R. Kish, "Corrosion Control of Type 316L Stainless Steel in Sulfamic Acid Cleaning Solutions", CORROSION, 65(7), pp.491~500 (2009), NACE International[DOI]
  27. J. H. SHIVELY, "Hydrogen Permeability of a Stable Austenitic Stainless Steel Under Anodic Polarization", CORROSION, 23, pp.215~ (1967)
  28. P. Villechaise, "On slip band features and crack initiation in fatigued 316L austenitic stainless steel: Part 1: Analysis by electron back-scattered diffraction and atomic force microscopy", Materials Science and Engineering: A, 323(1-2), pp.377~385 (2002), Elsevier BV[DOI]
  29. Herbert H. Uhlig, "Anodic Polarization of Passive and Non-passive Chromium–Iron Alloys.", The Journal of Physical Chemistry, 57(3), pp.280~283 (1953), American Chemical Society (ACS)[DOI]
  30. 황현규, "순환동전위 분극실험을 이용한 스테인리스강의 그린데스용액에서 전기화학적 특성에 미치는 온도의 영향", CORROSION SCIENCE AND TECHNOLOGY, 20(5), pp.266~280 (2021), 한국부식방식학회[DOI]
  31. 황현규, "배관의 부식 상태 진단에 사용되는 ER 부식센서의 가속부식환경에서의 신뢰성 평가", CORROSION SCIENCE AND TECHNOLOGY, 20(6), pp.403~411 (2021), 한국부식방식학회[DOI]
  32. G. T. Burstein, "Repetitive Nucleation of Corrosion Pits on Stainless Steel and the Effects of Surface Roughness", Journal of The Electrochemical Society, 148(12), pp.B504~ (2001), The Electrochemical Society[DOI]
  33. Arash Shahryari, "The effect of surface roughness on the efficiency of the cyclic potentiodynamic passivation (CPP) method in the improvement of general and pitting corrosion resistance of 316LVM stainless steel", Materials Letters, 62(23), pp.3906~3909 (2008), Elsevier BV[DOI]
  34. 신동호, "고분자 전해질 연료전지 금속분리판용 316L 스테인리스강의 양극작동조건에서 염화물 농도에 따른 부식 특성", CORROSION SCIENCE AND TECHNOLOGY, 20(6), pp.435~450 (2021), 한국부식방식학회[DOI]

관련 논문AI추천

오스테나이트 스테인리스강의 해수에서 전기화학적 특성에 미치는 전해연마시간의 영향김성종, 신동호, 허호성, 황현규한국표면공학회 · 한국표면공학회지2022 · 제55권 제4호전해연마한 슈퍼오스테나이트 스테인리스강의 해수온도에 따른 전기화학적 특성 연구김성종, 황현규한국재료부식학회 · CORROSION SCIENCE AND TECHNOLOGY2023 · 제22권 제3호산업현장 적용을 위한 스테인레스 스틸의 전해연마 특성김상범, 김수한, 박철환, 이승헌, 조재훈, 최중소한국표면공학회 · 한국표면공학회지2016 · 제49권 제4호다구찌 기법을 활용한 통계적·표면 분석에 따른 오스테나이트 스테인리스강의 전해연마조건 최적화 연구김성종, 황현규한국재료부식학회 · CORROSION SCIENCE AND TECHNOLOGY2022 · 제21권 제5호UNS S31603에 대하여 완전요인설계를 이용한 전해연마조건에 따른 표면 거칠기의 유효인자 산출김성종, 황현규한국재료부식학회 · CORROSION SCIENCE AND TECHNOLOGY2022 · 제21권 제4호오스테나이트 스테인리스강 저속인장시험편의 최적 전해연마 특성김동진, 조은별, 최민재한국재료부식학회 · CORROSION SCIENCE AND TECHNOLOGY2023 · 제22권 제6호

이 간행물의 다른 논문 (8건)

Corrosion Protection Effectiveness and Adsorption Performance of Schiff Base-Quinazoline on Mild Steel in HCl EnvironmentAli M. Mustafa, Mahdi M. Hanoon, Ahmed A. Al-Amiery, Lina M. Shaker, Firas F. Sayyidpp. 77-88A Newly Developed Non-Cyanide Electroless Gold Plating Method Using Thiomalic Acid as a Complexing Agent and 2-Aminoethanethiol as a Reducing AgentNguyen Van Phuong, 이재봉, 김동현, 한재호pp. 89-99Valorization of Cork Waste to Improve the Anti-Corrosion Properties of Concrete ReinforcementsS. Belkhir, J. P. Chopart, H. Bensabrapp. 100-110Coating Performance of SiO2/ Epoxy Composites as a Corrosion ProtectorNagham Y. Ahmed, Naseer Alhaboubi, Dina R. Rzaijpp. 111-120Optimization of Process Parameters for Dry Film Thickness to Achieve Superior Water-based Coating in Automotive IndustriesShailesh Kumar Prasad, Pranay Kant Prasad, Abhinav Kr Singh, Sandeep Singh, Sudhanshu Shekher Patipp. 121-129
원문 보기