고온 고압 응력부식균열 개시 시험용 디스크 시편의 응력과 변형에 대한 유한요소 해석
Finite Element Analysis of Stress and Strain Distribution on Thin Disk Specimen for SCC Initiation Test in High Temperature and Pressure Environment
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
The rupture disk corrosion test (RDCT) method was recently developed to evaluate stress corrosion cracking (SCC) and was found to have great potential for the real-time detection of SCC initiation in a high temperature and pressure environment, simulating the primary water coolant of pressurized water reactors. However, it is difficult to directly measure the stress applied to a disk specimen, which is an essential factor in SCC initiation. In this work, finite element analysis (FEA) was performed using ABAQUSTM to calculate the stress and deformation of a disk specimen. To determine the best mesh design for a thin disk specimen, hexahedron, hex-dominated, and tetrahedron models were used in FEA. All models revealed similar dome-shaped deformation behavior of the disk specimen. However, there was a considerable difference in stress distribution in the disk specimens. In the hex-dominated model, the applied stress was calculated to be the maximum at the dome center, whereas the stress was calculated to be the maximum at the dome edge in the hexahedron and tetrahedron models. From a comparison of the FEA results with deformation behavior and SCC location on the disk specimen after RDCT, the most proper FE model was found to be the tetrahedron model.
Abstract
The rupture disk corrosion test (RDCT) method was recently developed to evaluate stress corrosion cracking (SCC) and was found to have great potential for the real-time detection of SCC initiation in a high temperature and pressure environment, simulating the primary water coolant of pressurized water reactors. However, it is difficult to directly measure the stress applied to a disk specimen, which is an essential factor in SCC initiation. In this work, finite element analysis (FEA) was performed using ABAQUSTM to calculate the stress and deformation of a disk specimen. To determine the best mesh design for a thin disk specimen, hexahedron, hex-dominated, and tetrahedron models were used in FEA. All models revealed similar dome-shaped deformation behavior of the disk specimen. However, there was a considerable difference in stress distribution in the disk specimens. In the hex-dominated model, the applied stress was calculated to be the maximum at the dome center, whereas the stress was calculated to be the maximum at the dome edge in the hexahedron and tetrahedron models. From a comparison of the FEA results with deformation behavior and SCC location on the disk specimen after RDCT, the most proper FE model was found to be the tetrahedron model.
참고문헌 (22)
- D. Feron, "Corrosion issues in light water reactors - stress corrosion cracking" (2007), Woodhead Publishing Ltd.
- 김영식, "Relationship Between the Initiation and Propagation of SCC and the Electrochemical Noise of Alloy 600 for the Steam Generator Tubing of Nuclear Power Plants", CORROSION SCIENCE AND TECHNOLOGY, 9(2), pp.57~66 (2010), 한국부식방식학회
- 이연주, "EN-DCPD 방법을 이용한 Alloy 600 재료의 국부부식균열 연구", CORROSION SCIENCE AND TECHNOLOGY, 12(2), pp.93~101 (2013), 한국부식방식학회
- 황성식, "원자로 내부구조물 균열개시 민감도에 미치는 영향인자 고찰", CORROSION SCIENCE AND TECHNOLOGY, 20(4), pp.210~229 (2021), 한국부식방식학회[DOI]
- "ASTM G39-99, Standard Practice for Preparation and Use of Bent-Beam Stress-Corrosion Test Specimens", ASTM Standards, ~ (2016)
- "ASTM G30, Standard Practice for Making and Using U-Bend Stress-Corrosion Test Specimens. ASTM Book of Standards", ASTM West Conshohocken, ~ (2016)
- "ASTM G-38, Standard Practice for Making and Using C-Ring Stress-Corrosion Test Specimens", ASTM Standards, ~ (2013)
- Ziqing Zhai, "Stress corrosion crack initiation of alloy 600 in PWR primary water", Corrosion Science, 123, pp.76~87 (2017), Elsevier BV[DOI]
- P.J. Meadows, "International Round-Robin on Stress Corrosion Crack Initiation of Alloy 600 Material in Pressurized Water Reactor Primary Water", Corrosion, 76(8), pp.719~733 (2020), Association for Materials Protection and Performance (AMPP)[DOI]
- S. W. Kim, , Proc. Korean Nuclear Society 2021 Spring Meeting (2021)
- 전건우, "New test method for real-time measurement of SCC initiation of thin disk specimen in high-temperature primary water environment", Nuclear Engineering and Technology, 54(12), pp.4481~4490 (2022), 한국원자력학회[DOI]
- Validation of stress corrosion cracking initiation model for stainless steel and nickel alloys: Effects of Cold Work, "Y. Garud", EPRI, ~ (2012)
- Standard User's Manual, Version 6.9, "ABAQUS", pp.2009, M. Smith
- Hongbo Zhu, "Finite Element Analysis on the Temperature- Dependent Burst Behavior of Domed 316L Austenitic Stainless Steel Rupture Disc", Metals, 10(2), pp.232~ (2020), MDPI AG[DOI]
- 정재영, "Structural Analysis on the Superficial Grooving Stainless-Steel Thin-Plate Rupture Discs", International Journal of Precision Engineering and Manufacturing, 15(6), pp.1035~1040 (2014), 한국정밀공학회
- Teseo Schneider, "A Large-Scale Comparison of Tetrahedral and Hexahedral Elements for Solving Elliptic PDEs with the Finite Element Method", ACM Transactions on Graphics, 41(3), pp.1~14 (2022), Association for Computing Machinery (ACM)[DOI]
- Igor Simonovski, "Small punch tensile testing of curved specimens: Finite element analysis and experiment", International Journal of Mechanical Sciences, 120, pp.204~213 (2017), Elsevier BV[DOI]
- Stress analysis of a rupture disk, "R. W. Werne", University of California, ~, pp.UCID-16761 (1975)
- Xiangwei Kong, "Experimental and finite element optimization analysis on hydroforming process of rupture disc", Procedia Manufacturing, 15, pp.892~898 (2018), Elsevier BV[DOI]
- Karl-Fredrik Nilsson, "A Numerical and Experimental Assessment of the Small Punch Creep Test for 316L(N) Stainless Steels", Metals, 11(10), pp.1609~ (2021), MDPI AG[DOI]
- V. Brown, "Finite Element Modelling of the Small Punch Test for Structure Critical Design", PhD, pp.2020
- Jindřich Petruška, "Computational Simulation of Small Punch Test", Applied Mechanics and Materials, 232, pp.497~501 (2012), Trans Tech Publications, Ltd.[DOI]