Effect of cavity shape, bond quality and volume on dentin bond strength.
Effect of cavity shape,bond quality and volume on dentin bond strength
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
본 연구에서는 복합레진의 중합수축시 와동의 형태, 접착층의 성숙도, 및 와동의 부피가 와동저의 접착면에 발생되는 중합수축응력에 미치는 영향을 평가하였다. 1급 와동 충전시의 응력발생을 모방하기 위해, 98개의 대구치를 2 x 2 x 2 실험군에 무작위로 분배하고 교합면 상아질을 평탄하게 연마한 후, 복합레진 충전을 위한 몰드의 역할을 할 수 있는 구멍을 가진 iris를 올려놓고 복합레진을 bulk-filling법으로 충전하였다. 각각의 변수로서 와동 형태에 관하여는 iris 재질 (접착제를 도포한 상아질 iris: 높은 C-factor, Teflon 처리된 금속 iris: 낮은 C-factor), 접착층의 성숙도에 관하여는 2종의 접착제 (Scotchbond Multi-purpose와 Xeno III), 와동의 부피에 관하여는 iris내 구멍의 직경 (직경 1 또는 3 mm x 높이 1.5 mm)을 달리하여 전단접착강도를 측정하였다. 와동의 C-factor가 클수록, 접착층의 성숙도가 우수할수록 그리고 부피가 클수록 접착력은 유의하게 감소하였다. 복합레진이 중합될 때, 와동의 형태적 제한에 따라 레진-상아질 접착계면에 발생되는 중합수축응력은 접착이 우수할수록 복합레진의 부피가 클수록 증가되므로, C-factor를 정의할 때 와동의 형태뿐 아니라, 접착층의 성숙도와 복합레진의 부피도 함께 고려되어야 된다.
Abstract
The aim of this study was to evaluate the effect of cavity shape, bond quality of bonding agent and volume of resin composite on shrinkage stress developed at the cavity floor. This was done by measuring the shear bond strength with respect to iris materials (cavity shape; adhesive-coated dentin as a high C-factor and Teflon-coated metal as a low C-factor), bonding agents (bond quality; ScotchbondTM Multi-purpose and XenoIII) and iris hole diameters (volume; 1 mm or 3 mm in diameter x 1.5 mm in thickness). Ninety-six molars were randomly divided into 8 groups (2 x 2 x 2 experimental setup). In order to simulate a Class I cavity, shear bond strength was measured on the flat occlusal dentin surface with irises. The iris hole was filled with Z250 restorative resin composite in a bulk-filling manner. The data was analyzed using three-way ANOVA and the Tukey test. Fracture mode analysis was also done. When the cavity had high C-factor, good bond quality and large volume, the bond strength decreased significantly. The volume of resin composite restricted within the well-bonded cavity walls is also be suggested to be included in the concept of C-factor, as well as the cavity shape and bond quality. Since the bond quality and volume can exaggerate the effect of cavity shape on the shrinkage stress developed at the resin-dentin bond, resin composites must be filled in a method, which minimizes the volume that can increase the C-factor.
참고문헌 (23)
- "Setting stress in composite resin in relation to configuration of the restoration", pp.1636~1639
- "The competition between the composite-dentin bond strength and the polymerization contraction stress", pp.1396~1399
- "The influence of water storage and C-factor on the dentin-resin composite microtensile bond strength and debond pathway utilizing a filled and unfilled adhesive resin", 17, pp.268~276 (2001)
- "Evaluation of thermal cycling and mechanical loading on bond strength of a self-etching primer system to dentin", 18, pp.269~275 (2002)
- "Influence of c-factor and layering technique on microtensile bond strength to dentin", 20, pp.579~585 (2004)
- "Contraction stress and marginal adaptation of composite restorations in dentinal cavity", 13, pp.19~24 (1994)
- "Do dental composites always shrink toward the light", pp.1435~1445 (1998)
- "Direction of shrinkage of light-curing resin composites", 57, pp.310~315 (1999)
- "Effect of interfacial bond quality on the direction of polymerization shrinkage flow in resin composite restorations", 27, pp.297~304 (2002)
- "Interpretation of bond failure through conversion and residual solvent measurements and Weibull analyses of flexural and microtensile bond strengths of bonding agents", 21(4), pp.354~364 (2005)
- "Determinants of in vitro gap formation of resin composites", 32, pp.109~115 (2004)
- "Microtensile bond strength of eleven contemporary adhesives to dentin", 3, pp.237~245 (2001)
- "Relationship of dentin shear bond strengths to different laboratory test designs", 15, pp.185~192 (2002)
- "In vitro quality testing of dentin adhesives", 51, pp.263~269 (1993)
- "Shear vs", 74, pp.1591~1596 (1995)
- "Three-dimensional finite element analysis of the shear bond test", 11, pp.126~131 (1995)
- "The effect of local interfacial geometry on the measurement of the tensile bond strength to dentin", 70, pp.889~893 (1991)
- "Shear and tensile bond testing for resin cement evaluation", 11, pp.298~304 (1995)
- "Dentin sher strength:Effects of tubule orientation and intratooth location", 11, pp.109~115 (1996)
- "The effects of bonding system and light curing method on reducing stress of different C-factor cavities", 3, pp.177~183 (2001)
- "Relationship between surface area for adhesion and tensile bond strength--evaluation of a micro-tensile bond test", 10, pp.236~40 (1994)
- "Effects of the acetone content of single solution dentin bonding agents on the adhesive layer thickness and the microtensile bond strength", 20, pp.107~115 (2004)
- "Effects of the acetone content of single solution dentin bonding agents on the adhesive layer thickness and the microtensile bond strength", 20, pp.107~115 (2004)