Numerical and experimental investigation of conventional and un-conventional preswirl duct for VLCC
2
조회
0
다운로드
7
인용
0
참고문헌
키워드
초록
This paper shows the study of preswirl duct as an effective energy saving devices that have been devised and reviewed to support the propeller performance, especially for the ship of VLCC with large block coefficients. From the bare hull wake measurements, typical upper/lower asymmetry of hull wake at the propeller disk was found. The 2kinds of pre-swirl duct, Unconventional half circular duct and Conventional circular pre-swirl duct have been designed and reviewed to recover the loss of propeller running in that condition. The general function of the pre-swirl duct was set to work against this asymmetry of wake and generate pre-swirled flow into the propeller against the propeller rotating direction. The optimum self propulsion tests with various angle configurations were carried out and the best configuration was decided. Accordingly, cavitation test was carried out with best configuration of unconventional half circular duct. The blade surface and tip vortex cavitation behaved smoother when the duct was mounted. The hull pressure amplitudes reflected this difference, so the hull pressure amplitude with duct was smaller than that of without duct.
Abstract
This paper shows the study of preswirl duct as an effective energy saving devices that have been devised and reviewed to support the propeller performance, especially for the ship of VLCC with large block coefficients. From the bare hull wake measurements, typical upper/lower asymmetry of hull wake at the propeller disk was found. The 2kinds of pre-swirl duct, Unconventional half circular duct and Conventional circular pre-swirl duct have been designed and reviewed to recover the loss of propeller running in that condition. The general function of the pre-swirl duct was set to work against this asymmetry of wake and generate pre-swirled flow into the propeller against the propeller rotating direction. The optimum self propulsion tests with various angle configurations were carried out and the best configuration was decided. Accordingly, cavitation test was carried out with best configuration of unconventional half circular duct. The blade surface and tip vortex cavitation behaved smoother when the duct was mounted. The hull pressure amplitudes reflected this difference, so the hull pressure amplitude with duct was smaller than that of without duct.
참고문헌 (14)
- Andersen, P., "A comparative study of conventional and Tip-Fin propeller performance", n Proceeding of 21st Symposium on Naval Hydrodynamics (1996)
- Carlton, J. S., "Thrust augmentation devices, In Marine propellers and propulsion", pp.299~324 (1994), Butterworth and Heinemann
- Grim, O., "Propeller and vane wheel", Journal of Ship Research, 24(4), pp.203~226 (1980)
- Hollstein, H. J., "Bulk carrier speed trials with a Sistemar CLT propeller", The Naval Architect, pp.33~36 (1997)
- Report of the specialist committee on unconventional propulsors, "ITTC", ITTC, 1~35 (1996)
- Van Lammeren, W. P. A., "Some Constructions for the improvement of the Efficiency of the Propulsion", Schipen Werf, No. 7, ~ (1949)
- Mewis, F., "Special measures for improving propulsive efficiency", HSVA NewsWave, Jan 2006. The newsletter from HSVA, ~ (2006)
- Mewis, F., "Power savings through a novel fin system", 15. SMSSH Conference Proceedings. Varna, Bulgaria, pp.9.1~9.6 (1986)
- Ogura, M., "A screw propeller boss cap with fins", UK. Pat. Application, GB 2194295 A, ~ (1987)
- Qian, W. H., "The exploratory development of simplified compensate nozzle and its composite device", Proceedings of the 2nd International Symposium on Propeller and Cavitation. Hangzhou, China (1992)
- Qian, W. H., "A new type of ship energy-saving device-fore-propeller hydrodynamic fin sector", Journal of Kansai Society of Naval Architects of Japan, 218, pp.163~169 (1992)
- Schneekluth, H., "Wake equalizing duct", The Naval Architect, April, 1986, 1986
- Sparenberg, J.A., "An optimum screw propeller with endplates", International Shipbuilding Progress, 34(395), pp.124~133 (1987)
- Zhou, Z.M., "Energy-saving shaft bracket suitable for multi-screw vessels", Shipbuilding of China, 109(2), pp.16~21 (1990)