CFD를 이용한 180,000 DWT Bulk Carrier용 Pre-Swirl Duct의 파라메트릭 설계
Parametric Designs of a Pre-swirl Duct for the 180,000DWT Bulk Carrier Using CFD
2
조회
0
다운로드
4
인용
0
참고문헌
키워드
초록
In this study, a pre-swirl duct for the 180,000 DWT bulk carrier has been designed from a propulsion standpoint using CFD. The stern duct - designed by NMRI - was selected as the initial duct. The objective function is to minimize the value of delivered power in model scale. Design variables of the duct include duct angle, diameter, chord length, and vertical and horizontal displacements from the center. Design variables of the stators are blade number, arrangement angle, chord length, and pitch angle. A parametric design was carried out with the objective function obtained using CFD. Reynolds averaged Navier-Stokes equations have been solved; and the Reynolds stress model applied for the turbulent closure. A double body model is used for the treatment of free-surface. MRF and sliding mesh models have been applied to simulate the actuating propeller. A self-propulsion point has been obtained from the results of towing and self-propelled computations, i.e., form factor obtained from towing computation and towing forces obtained from self-propelled computations of two propeller rotating speeds. The reduction rate of the delivered power of the improved stern duct is 2.9%, whereas that of the initial stern duct is 1.3%. The pre-swirl duct with one inner stator in upper starboard and three outer stators in portside has been designed. The delivered power due to the designed pre-swirl duct is reduced by 5.8%.
Abstract
In this study, a pre-swirl duct for the 180,000 DWT bulk carrier has been designed from a propulsion standpoint using CFD. The stern duct - designed by NMRI - was selected as the initial duct. The objective function is to minimize the value of delivered power in model scale. Design variables of the duct include duct angle, diameter, chord length, and vertical and horizontal displacements from the center. Design variables of the stators are blade number, arrangement angle, chord length, and pitch angle. A parametric design was carried out with the objective function obtained using CFD. Reynolds averaged Navier-Stokes equations have been solved; and the Reynolds stress model applied for the turbulent closure. A double body model is used for the treatment of free-surface. MRF and sliding mesh models have been applied to simulate the actuating propeller. A self-propulsion point has been obtained from the results of towing and self-propelled computations, i.e., form factor obtained from towing computation and towing forces obtained from self-propelled computations of two propeller rotating speeds. The reduction rate of the delivered power of the improved stern duct is 2.9%, whereas that of the initial stern duct is 1.3%. The pre-swirl duct with one inner stator in upper starboard and three outer stators in portside has been designed. The delivered power due to the designed pre-swirl duct is reduced by 5.8%.
참고문헌 (13)
- Choi, J.E., "Resistance and Propulsion Characteristics of Various Commercial Ships based on CFD Results", Ocean Engineering, 37, pp.549~566 (2010)
- 강용덕, "편재된 비대칭형 전류고정날개 추진시스템에 관한 연구", 대한조선학회 논문집, 41(3), pp.13~21 (2004), 대한조선학회
- 김정현, "Twisted rudder for reducing fuel-oil consumption", International Journal of Naval Architecture and Ocean Engineering, 6(3), pp.715~722 (2014), 대한조선학회
- 김정훈, "Development of energy-saving devices for a full slow-speed ship through improving propulsion performance", International Journal of Naval Architecture and Ocean Engineering, 7(2), pp.390~398 (2015), 대한조선학회
- Kim, M.C., "A Study on the Asymmetric Preswirl Stator System", Journal of the Society of Naval Architects of Korea, 30(1), pp.30~44 (1993)
- Lee, J.T., "Development of a Preswirl Stator-propeller System for Improvement Propulsion Efficiency : a Symmetric Stator propulsion system", Journal of the Society of Naval Architects of Korea, 29(4), pp.132~145 (1992)
- Lee, J.T., "Development of a Preswirl Stator Propulsion System for a 300K VLCC", Journal of the Society of Naval Architects of Korea, 31(1), pp.1~13 (1994)
- Mewis, F., "Mewis duct – new developments, solutions and conclusions", Second International Symposium on Marine Propulsors (2011)
- Schneekluth, H., "Wake Equalizing Euct", The Naval Architect, 103, pp.147~150 (1986)
- Stern, F., "Quantitative Approach to V&V of CFD Simulations and Certification of CFD Codes", International Journal of Numerical Methods in Fluids, 50, pp.1335~1355 (2006)
- 신현준, "Numerical and experimental investigation of conventional and un-conventional preswirl duct for VLCC", International Journal of Naval Architecture and Ocean Engineering, 5(3), pp.414~430 (2013), 대한조선학회
- Yang, J.M., "Effect of pre-swirl stator vane on the pro-peller hull interaction of a full ship", Proceedings of the Annual Autumn Meeting, SNAK, pp.188~191 (2000)
- Yang, J.M., "Effect of pre-swirl stator vane on the propeller hull interaction (2)", Proceedings of the Annual Autumn Meeting, SNAK, pp.216~219 (2001)