Prosthetic misfit of implant-supported prosthesis obtained by an alternative section method
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
PURPOSE. Adequate passive-fitting of one-piece cast 3-element implant-supported frameworks is hard to achieve. This short communication aims to present an alternative method for section of one-piece cast frameworks and for casting implant-supported frameworks. MATERIALS AND METHODS. Three-unit implant-supported nickel-chromium (Ni-Cr) frameworks were tested for vertical misfit (n = 6). The frameworks were cast as one-piece (Group A) and later transversally sectioned through a diagonal axis (Group B) and compared to frameworks that were cast diagonally separated (Group C). All separated frameworks were laser welded. Only one side of the frameworks was screwed. RESULTS. The results on the tightened side were significantly lower in Group C (6.43 ± 3.24 ㎛) when compared to Groups A (16.50 ± 7.55 ㎛) and B (16.27 ± 1.71 ㎛) (P<.05). On the opposite side, the diagonal section of the one-piece castings for laser welding showed significant improvement in the levels of misfit of the frameworks (Group A, 58.66±14.30 ㎛ Group B, 39.48±12.03 ㎛ Group C, 23.13±8.24 ㎛) (P<.05). CONCLUSION. Casting diagonally sectioned frameworks lowers the misfit levels. Lower misfit levels for the frameworks can be achieved by diagonally sectioning one-piece frameworks.
Abstract
PURPOSE. Adequate passive-fitting of one-piece cast 3-element implant-supported frameworks is hard to achieve. This short communication aims to present an alternative method for section of one-piece cast frameworks and for casting implant-supported frameworks. MATERIALS AND METHODS. Three-unit implant-supported nickel-chromium (Ni-Cr) frameworks were tested for vertical misfit (n = 6). The frameworks were cast as one-piece (Group A) and later transversally sectioned through a diagonal axis (Group B) and compared to frameworks that were cast diagonally separated (Group C). All separated frameworks were laser welded. Only one side of the frameworks was screwed. RESULTS. The results on the tightened side were significantly lower in Group C (6.43 ± 3.24 ㎛) when compared to Groups A (16.50 ± 7.55 ㎛) and B (16.27 ± 1.71 ㎛) (P<.05). On the opposite side, the diagonal section of the one-piece castings for laser welding showed significant improvement in the levels of misfit of the frameworks (Group A, 58.66±14.30 ㎛ Group B, 39.48±12.03 ㎛ Group C, 23.13±8.24 ㎛) (P<.05). CONCLUSION. Casting diagonally sectioned frameworks lowers the misfit levels. Lower misfit levels for the frameworks can be achieved by diagonally sectioning one-piece frameworks.
참고문헌 (27)
- Sahin S, "The significance of passive framework fit in implant prosthodontics: current status", Implant Dent, 10, pp.85~92 (2001)
- Kohorst P, "Marginal accuracy of four-unit zirconia fixed dental prostheses fabricated using different computer-aided design", computer-aided manufacturing systems, 2009, pp.117, 319~325
- Jemt T., "Failures and complications in 391 consecutively inserted fixed prostheses supported by Branemark implants in edentulous jaws: a study of treatment from the time of prosthesis placement to the first annual checkup", Int J Oral Maxillofac Implants, 6, pp.270~276 (1991)
- Tiossi R, "Comparative analysis of the fit of 3-unit implant-supported frameworks cast in nickel-chromium and cobalt-chromium alloys and commercially pure titanium after casting, laser welding, and simulated porcelain firings", Int J Prosthodont, 21, pp.121~123 (2008)
- Clelland NL, "Comparison of strains transferred to a bone simulant between as-cast and postsoldered implant frameworks for a five-implant-supported fixed prosthesis", J Prosthodont, 5, pp.193~200 (1996)
- Koke U, "In vitro investigation of marginal accuracy of implant-supported screw-retained partial dentures", J Oral Rehabil, 31, pp.477~482 (2004)
- Silva TB, "Influence of laser-welding and electroerosion on passive fit of implant-supported prosthesis", Stomatologija, 10, pp.96~100 (2008)
- de Sousa SA, "Passive fit of frameworks in titanium and palladium-silver alloy submitted the laser welding", J Oral Rehabil, 35, pp.123~127 (2008)
- Tiossi R, "Modified section method for laser-welding of ill-fitting cp Ti and Ni-Cr alloy one-piece cast implant-supported frameworks", J Oral Rehabil, 37, pp.359~363 (2010)
- de Aguiar FA Jr, "An alternative section method for casting and posterior laser welding of metallic frameworks for an implantsupported prosthesis", J Prosthodont, 18, pp.230~234 (2009)
- Kikuchi H, "Effect of laser irradiation conditions on the laser welding strength of cobalt-chromium and gold alloys", J Oral Sci, 53, pp.301~305 (2011)
- Sartori IA, "In vitro comparative analysis of the fit of gold alloy or commercially pure titanium implant-supported prostheses before and after electroerosion", J Prosthet Dent, 92, pp.132~138 (2004)
- Watanabe I, "Tensile strength of soldered gold alloy joints", J Prosthet Dent, 78, pp.260~266 (1997)
- Fonseca JC, "Stressrelieving and porcelain firing cycle influence on marginal fit of commercially pure titanium and titanium-aluminum-vanadium copings", Dent Mater, 19, pp.686~691 (2003)
- Wettstein F, "Clinical study of the internal gaps of zirconia and metal frameworks for fixed partial dentures", Eur J Oral Sci, 116, pp.272~279 (2008)
- Jemt T, "Prosthesis misfit and marginal bone loss in edentulous implant patients", Int J Oral Maxillofac Implants, 11, pp.620~625 (1996)
- Shimakura M, "Influence of irradiation conditions on the deformation of pure titanium frames in laser welding", Dent Mater J, 28, pp.243~247 (2009)
- Nuñez-Pantoja JM, "Effects of laser-weld joint opening size on fatigue strength of Ti-6Al-4V structures with several diameters", J Oral Rehabil, 38, pp.196~201 (2011)
- Zupancic R, "Tensile strength and corrosion resistance of brazed and laser-welded cobalt-chromium alloy joints", J Prosthet Dent, 96, pp.273~282 (2006)
- Gemalmaz D, "Thermal cycling distortion of porcelain fused to metal fixed partial dentures", J Prosthet Dent, 80, pp.654~660 (1998)
- Bridger DV, "Distortion of ceramometal fixed partial dentures during the firing cycle", J Prosthet Dent, 45, pp.507~514 (1981)
- Campbell SD, "Thermal cycling distortion of metal ceramics: Part I-Metal collar width", J Prosthet Dent, 67, pp.603~608 (1992)
- Campbell SD, "Effects of firing cycle and surface finishing on distortion of metal ceramic castings", J Prosthet Dent, 74, pp.476~481 (1995)
- Twiggs SW, "A rapid heating and cooling rate dilatometer for measuring thermal expansion in dental porcelain", J Dent Res, 68, pp.1316~1318 (1989)
- Bryant RA, "Measurement of distortions in fixed partial dentures resulting from degassing", J Prosthet Dent, 42, pp.515~520 (1979)
- Ziebert GJ, "Accuracy of one-piece castings, preceramic and postceramic soldering", J Prosthet Dent, 55, pp.312~317 (1986)
- Zervas PJ, "Distortion of threeunit implant frameworks during casting, soldering, and simulated porcelain firings", J Prosthodont, 8, pp.171~179 (1999)