Effects of the sintering conditions of dental zirconia ceramics on the grain size and translucency
2
조회
0
다운로드
16
인용
0
참고문헌
키워드
초록
PURPOSE. This study aimed to identify the effects of the sintering conditions of dental zirconia on the grain size and translucency. MATERIALS AND METHODS. Ten specimens of each of two commercial brands of zirconia (Lava and KaVo) were made and sintered under five different conditions. Microwave sintering (MS) and conventional sintering (CS) methods were used to fabricate zirconia specimens. The dwelling time was 20 minutes for MS and 20 minutes, 2, 10, and 40 hours for CS. The density and the grain size of the sintered zirconia blocks were measured. Total transmission measurements were taken using a spectrophotometer. Twoway analysis of variance model was used for the analysis and performed at a type-one error rate of 0.05. RESULTS. There was no significant difference in density between brands and sintering conditions. The mean grain size increased according to sintering conditions as follows: MS-20 min, CS-20 min, CS-2 hr, CS-10 hr, and CS-40 hr for both brands. The mean grain size ranged from 347-1,512 nm for Lava and 373-1,481 nm for KaVo. The mean light transmittance values of Lava and KaVo were 28.39-34.48% and 28.09-30.50%, respectively. CONCLUSION. Different sintering conditions resulted in differences in grain size and light transmittance. To obtain more translucent dental zirconia restorations, shorter sintering times should be considered.
Abstract
PURPOSE. This study aimed to identify the effects of the sintering conditions of dental zirconia on the grain size and translucency. MATERIALS AND METHODS. Ten specimens of each of two commercial brands of zirconia (Lava and KaVo) were made and sintered under five different conditions. Microwave sintering (MS) and conventional sintering (CS) methods were used to fabricate zirconia specimens. The dwelling time was 20 minutes for MS and 20 minutes, 2, 10, and 40 hours for CS. The density and the grain size of the sintered zirconia blocks were measured. Total transmission measurements were taken using a spectrophotometer. Twoway analysis of variance model was used for the analysis and performed at a type-one error rate of 0.05. RESULTS. There was no significant difference in density between brands and sintering conditions. The mean grain size increased according to sintering conditions as follows: MS-20 min, CS-20 min, CS-2 hr, CS-10 hr, and CS-40 hr for both brands. The mean grain size ranged from 347-1,512 nm for Lava and 373-1,481 nm for KaVo. The mean light transmittance values of Lava and KaVo were 28.39-34.48% and 28.09-30.50%, respectively. CONCLUSION. Different sintering conditions resulted in differences in grain size and light transmittance. To obtain more translucent dental zirconia restorations, shorter sintering times should be considered.
참고문헌 (39)
- Kelly JR, "Ceramics in dentistry:historical roots and current perspectives", J Prosthet Dent, 75, pp.18~32 (1996)
- Fischer H, "Lifetime prediction of all-ceramic bridges by computational methods", J Dent Res, 82, pp.238~242 (2003)
- Conrad HJ, "Current ceramic materials and systems with clinical recommendations: a systematic review", J Prosthet Dent, A98, pp.389~404 (2007)
- Tinschert J, "Spiekermann H. Fracture resistance of lithium disilicate-, alumina-, and zirconia-based three-unit fixed partial dentures: a laboratory study", Int J Prosthodont, 14, pp.231~238 (2001)
- Chen YM, "Translucency and biaxial flexural strength of four ceramic core materials", Dent Mater, 24, pp.1506~1511 (2008)
- Akagawa Y, "Comparison between freestanding and tooth-connected partially stabilized zirconia implants after two years’ function in monkeys: a clinical and histologic study", J Prosthet Dent, 80, pp.551~558 (1998)
- Ichikawa Y, "Tissue compatibility and stability of a new zirconia ceramic in vivo", J Prosthet Dent, 68, pp.322~326 (1992)
- Scarano A, "Bone response to zirconia ceramic implants: an experimental study in rabbits", J Oral Implantol, 29, pp.8~12 (2003)
- Rosenstiel SF, "Contemporary Fixed Prosthodontics", pp.262~643 (2006), Mosby
- Yu B, "Measurement of translucency of tooth enamel and dentin", Acta Odontol Scand, 67, pp.57~64 (2009)
- Heffernan MJ, "Haselton DR,Stanford CM, Vargas MA. Relative translucency of six all-ceramic systems. Part I: core materials", J Prosthet Dent, 88, pp.4~9 (2002)
- Heffernan MJ, "Relative translucency of six all-ceramic systems. Part II: core and veneer materials", J Prosthet Dent, 88, pp.10~15 (2002)
- Vichi A, "Color related to ceramic and zirconia restorations: a review", Dent Mater, 27, pp.97~108 (2011)
- Brodbelt RH, "Translucency of dental porcelains", J Dent Res, 59, pp.70~75 (1980)
- Peelen JGJ, "Light-scattering by pores in polycrystalline materials: transmission properties of alumina", J Appl Phys, 45, pp.216~220 (1974)
- Zhang HB, "Optimization of high-pressure sintering of transparent zirconia with nano-sized grains", J Alloy Compd, 508, pp.196~199 (2010)
- Clarke FJ, "Measurement of color of human teeth", Proceedings of the First International Symposium on Ceramics, pp.441~490 (1983), Quintessence
- Casolco SR, "Transparent", translucent polycrystalline nanostructured yttria stabilized zirconia with varying colors, 2008, pp.58, 516~519
- Jiang L, "Effects of sintering temperature and particle size on the translucency of zirconium dioxide dental ceramic", J Mater Sci Mater Med, 22, pp.2429~2435 (2011)
- Anselmi-Tamburini U, "Transparent nanometric cubic and tetragonal zirconia obtained by highpressure pulsed electric current sintering", Adv Funct Mater, 17, pp.3267~3273 (2007)
- Yang D, "Enhanced sintering rate of Zirconia (3Y-TZP) through the effect of a weak dc electric field on grain growth", J Am Ceram Soc, 93, pp.2935~2937 (2010)
- Janney MA, "Microwave sintering of solid oxide fuel cell materials: I, Zirconia-8 mol% Yttria", J Am Ceram Soc, 75, pp.341~346 (1992)
- Li JF, "Phase Transformation in Y2O3-Partially-Stabilized ZrO2 Polycrystals of Various Grain Sizes during Low-Temperature Aging in Water", J Am Ceram Soc, 81, pp.2687~2691 (1998)
- Ebadzadeh T, "Microwave-assisted sintering of zircon", J Alloy Compd, 448, pp.246~249 (2008)
- Cheng J, "Microwave sintering of transparent alumina", Mater Lett, 56, pp.587~592 (2002)
- Luo J, "Microstructure evolution and grain growth in the sintering of 3Y-TZP ceramics", J Mater Sci, 33, pp.5301~5309 (1998)
- "ISO 18754 - Fine ceramics-advanced ceramics, advanced technical ceramics-Determination of density and apparent porosity", ISO, ~ (2008)
- ASTM, "Standard test method for determining average grain size E112-96", Part 301, pp.243~266 (2003)
- Mendelson MI, "Average Grain Size in Polycrystalline Ceramics", J Am Ceram Soc, 52, pp.443~446 (1969)
- Cook WD, "Optical properties of esthetic restorative materials and natural dentition", J Biomed Mater Res, 19, pp.469~488 (1985)
- Lee YK, "Influence of scattering", absorption characteristics on the color of resin composites, 2007, pp.23, 124~131
- O’'Brien WJ, "Double-layer color effects in porcelain systems", J Dent Res, 64, pp.940~943 (1985)
- Hayashi K, "Transmission optical properties of polycrystalline alumina with submicron grains", Mater Trans JIM, 32, pp.1024~1029 (1991)
- O YT, "Effect of grain size on transmittance and mechanical strength of sintered alumina", Mat Sci Eng A, 374, pp.191~195 (2004)
- Apetz R, "Transparent alumina: A light scattering model", J Am Ceram Soc, 86, pp.480~486 (2003)
- Alaniz JE, "Optical properties of transparent nanocrystalline yttria stabilized zirconia", Opt Mater, 32, pp.62~68 (2009)
- "ISO 13356 - Implants for surgery-Ceramic materials based on yttria-stabilized tetragonal zirconia (Y-TZP)", ISO, ~ (2008)
- Tekeli S, "A quantitative assessment of cavities in 3 mol% yttria-stabilized tetragonal zirconia specimens containing various grain size", Ceram Int, 28, pp.785~789 (2002)
- Hjerppe J, "Effect of sintering time on biaxial strength of zirconium dioxide", Dent Mater, 25, pp.166~171 (2009)