Effects of different surface finishing procedures on the change in surface roughness and color of a polymer infiltrated ceramic network material
2
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
PURPOSE. Polymer infiltrated ceramic network (PICN) materials, also called hybrid ceramics, are new materials in dental market. The manufacturer of the PICN material VITA Enamic suggests 3 different finishing procedures for this new material. In the present study, surface roughness and color differences caused from different finishing procedures of VITA Enamic were investigated. MATERIALS AND METHODS. 120 specimens were prepared in dimensions 2 × 10 × 12 mm from VITA Enamic hybrid ceramic blocks with ‘high translucency’ and ‘translucency 2M2’ shades. The specimens were divided into 8 groups. For each group, different finishing procedures suggested by the manufacturer were performed. Surface roughness values were determined by a tactile portable profilometer. Color changes were evaluated using a clinical spectrophotometer. The data were analyzed using one-way ANOVA and Tukey’s post-hoc comparison. The significance level was set at α=0.05. RESULTS. The roughest surfaces were observed in Glaze Groups. Their surface roughness values were similar to that of the control group. Clinical Kit and Technical Kit groups did not show a statistically significant difference regarding surface roughness (P>.05). The largest color difference regarding ΔE00 was observed in Clinical Kit finishing groups. There were also statistically significant color changes between the groups (P<.05). However, all the groups showed clinically acceptable color change (ΔE00<2.25) except Clinical Kit Groups (ΔE00>2.25). CONCLUSION. Within the limitations of the present study, it may be suggested that finishing the VITA Enamic restorations by Technical Kit instead of Glaze and Clinical Kit gives better clinical performance in regard to surface roughness and shade matching.
Abstract
PURPOSE. Polymer infiltrated ceramic network (PICN) materials, also called hybrid ceramics, are new materials in dental market. The manufacturer of the PICN material VITA Enamic suggests 3 different finishing procedures for this new material. In the present study, surface roughness and color differences caused from different finishing procedures of VITA Enamic were investigated. MATERIALS AND METHODS. 120 specimens were prepared in dimensions 2 × 10 × 12 mm from VITA Enamic hybrid ceramic blocks with ‘high translucency’ and ‘translucency 2M2’ shades. The specimens were divided into 8 groups. For each group, different finishing procedures suggested by the manufacturer were performed. Surface roughness values were determined by a tactile portable profilometer. Color changes were evaluated using a clinical spectrophotometer. The data were analyzed using one-way ANOVA and Tukey’s post-hoc comparison. The significance level was set at α=0.05. RESULTS. The roughest surfaces were observed in Glaze Groups. Their surface roughness values were similar to that of the control group. Clinical Kit and Technical Kit groups did not show a statistically significant difference regarding surface roughness (P>.05). The largest color difference regarding ΔE00 was observed in Clinical Kit finishing groups. There were also statistically significant color changes between the groups (P<.05). However, all the groups showed clinically acceptable color change (ΔE00<2.25) except Clinical Kit Groups (ΔE00>2.25). CONCLUSION. Within the limitations of the present study, it may be suggested that finishing the VITA Enamic restorations by Technical Kit instead of Glaze and Clinical Kit gives better clinical performance in regard to surface roughness and shade matching.
참고문헌 (17)
- Della Bona A, "Characterization of a polymer-infiltrated ceramic-network material", Dent Mater, 30, pp.564~569 (2014)
- Coldea A, "In-vitro strength degradation of dental ceramics and novel PICN material by sharp indentation", J Mech Behav Biomed Mater, 26, pp.34~42 (2013)
- He LH, "A novel polymer infiltrated ceramic dental material", Dent Mater, 27, pp.527~534 (2011)
- Nguyen JF, "High-temperaturepressure polymerized resin-infiltrated ceramic networks", J Dent Res, 93, pp.62~67 (2014)
- Ghinea R, "Color difference thresholds in dental ceramics", J Dent, 38, pp.e57~e64 (2010)
- Coldea A, "Mechanical properties of polymer-infiltrated-ceramic-network materials", Dent Mater, 29, pp.419~426 (2013)
- Coldea A, "Hertzian contact response and damage tolerance of dental ceramics", J Mech Behav Biomed Mater, 34, pp.124~133 (2014)
- Bottino MA, "Inlays made from a hybrid material: adaptation and bond strengths", Oper Dent, 40, pp.E83~E91 (2015)
- van der Burgt TP, "A comparison of new and conventional methods for quantification of tooth color", J Prosthet Dent, 63, pp.155~162 (1990)
- Uludag B, "The effect of ceramic thickness and number of firings on the color of ceramic systems: an in vitro study", J Prosthet Dent, 97, pp.25~31 (2007)
- Monasky GE, "Studies on the wear of porcelain, enamel, and gold", J Prosthet Dent, 25, pp.299~306 (1971)
- 정유석, "A study on the in-vitro wear of the natural tooth structure by opposing zirconia or dental porcelain", The Journal of Advanced of Prosthodontics, 2(3), pp.111~115 (2010), 대한치과보철학회
- Fasbinder DJ, "Surface Evaluation of Polishing Techniques for New Resilient CAD", CAM Restorative Materials, 2015, ~
- Haghi HR, "Effect of denture cleansers on color stability and surface roughness of denture base acrylic resin", Indian J Dent Res, 26, pp.163~166 (2015)
- Roque AC, "Surface roughness of composite resins subjected to hydrochloric acid", Braz Dent J, 26, pp.268~271 (2015)
- Ţălu Ş, "Morphology of Co-Cr-Mo dental alloy surfaces polished by three different mechanical procedures", Microsc Res Tech, 78, pp.831~839 (2015)
- Quirynen M, "The clinical meaning of the surface roughness and the surface free energy of intra-oral hard substrata on the microbiology of the supra- and subgingival plaque: results of in vitro and in vivo experiments", J Dent, 22, pp.S13~S16 (1994)