Color stability of 3D-printed denture resins: effect of aging, mechanical brushing and immersion in staining medium
1
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
Purpose. This in-vitro study evaluated and compared the color stability of 3D-printed and conventional heat-polymerized acrylic resins following aging, mechanical brushing, and immersion in staining medium. Materials and methods. Forty disc-shaped specimens (10 mm in diameter and 3 mm thick) were prepared from two 3D-printed [DentaBASE (DB) and Denture 3D+ (D3D)] and one conventional polymethylmethacrylate (PMMA) denture materials. The specimens were thermo-cycled, subjected to mechanical brushing, and were immersed in either coffee, lemon juice, coke, or artificial saliva (AS) to simulate one and two years of oral use. Color measurements of the specimens were recorded by a spectrophotometer at baseline (T0), and after one (T1) and two years (T2) of simulation. The color changes (ΔE) were determined and also quantified according to the National Bureau of Standards (NBS) units. Descriptive statistics, followed by factorial ANOVA and Bonferroni post-hoc test (α=.05), were applied for data analysis. Results. The independent factors, namely material, staining medium, and immersion time, and interaction among these factorssignificantly influenced ΔE (P <.009). Irrespective of the materials, treatments, and time, the highest and the lowest mean ΔEs were observed for PMMA in lemon juice (4.58 ± 1.30) and DB in AS (0.41 ± 0.18), respectively. Regarding the material type, PMMA demonstrated the highest mean ΔE (2.31 ± 1.37), followed by D3D (1.67 ± 0.66), and DB (0.85 ± 0.52), and the difference in ΔE between the materials were statistically significant (P <.001). All the specimens demonstrated a decreased color changes at T2 compared to T1, and this difference in mean ΔE was statistically significant (P <.001). Conclusion. The color changes of 3D-printed denture resins were low compared to conventional heat polymerized PMMA. All the tested materials, irrespective of the staining medium used, demonstrated a significant decrease in ΔE values over time.
Abstract
Purpose. This in-vitro study evaluated and compared the color stability of 3D-printed and conventional heat-polymerized acrylic resins following aging, mechanical brushing, and immersion in staining medium. Materials and methods. Forty disc-shaped specimens (10 mm in diameter and 3 mm thick) were prepared from two 3D-printed [DentaBASE (DB) and Denture 3D+ (D3D)] and one conventional polymethylmethacrylate (PMMA) denture materials. The specimens were thermo-cycled, subjected to mechanical brushing, and were immersed in either coffee, lemon juice, coke, or artificial saliva (AS) to simulate one and two years of oral use. Color measurements of the specimens were recorded by a spectrophotometer at baseline (T0), and after one (T1) and two years (T2) of simulation. The color changes (ΔE) were determined and also quantified according to the National Bureau of Standards (NBS) units. Descriptive statistics, followed by factorial ANOVA and Bonferroni post-hoc test (α=.05), were applied for data analysis. Results. The independent factors, namely material, staining medium, and immersion time, and interaction among these factorssignificantly influenced ΔE (P <.009). Irrespective of the materials, treatments, and time, the highest and the lowest mean ΔEs were observed for PMMA in lemon juice (4.58 ± 1.30) and DB in AS (0.41 ± 0.18), respectively. Regarding the material type, PMMA demonstrated the highest mean ΔE (2.31 ± 1.37), followed by D3D (1.67 ± 0.66), and DB (0.85 ± 0.52), and the difference in ΔE between the materials were statistically significant (P <.001). All the specimens demonstrated a decreased color changes at T2 compared to T1, and this difference in mean ΔE was statistically significant (P <.001). Conclusion. The color changes of 3D-printed denture resins were low compared to conventional heat polymerized PMMA. All the tested materials, irrespective of the staining medium used, demonstrated a significant decrease in ΔE values over time.
참고문헌 (51)
- Cunha-Cruz J, "Secular trends in socio-economic disparities in edentulism:USA, 1972-2001", J Dent Res, 86, pp.131~136 (2007)
- Emami E, "The impact of edentulism on oral and general health", Int J Dent, 2013, pp.498305~ (2013)
- Anadioti E, "3D printed complete removable dental prostheses : a narrative review", BMC Oral Health, 20, pp.e343~ (2020)
- Al-Dwairi ZN, "A comparison of the surface properties of CAD", CAM and conventional polymethylmethacrylate (PMMA), 2019, pp.28, 452~457
- Paulino MR, "Simplified versus traditional techniques for complete denture fabrication : a systematic review", J Prosthet Dent, 113, pp.12~16 (2015)
- Saponaro PC, "Clinical performance of CAD-CAM-fabricated complete dentures : a cross-sectional study", J Prosthet Dent, 116, pp.431~435 (2016)
- Gruber S, "CAD", CAM complete denture resins : an in vitro evaluation of color stability, 2021, pp.30, 430~439
- Dayan C, "A comparison of the color stability of conventional and CAD", CAM polymethyl methacrylate denture base materials, 2019, pp.53, 158~167
- Singh S, "Comparative evaluation of surface porosities in conventional heat polymerized acrylic resin cured by water bath and microwave energy with microwavable acrylic resin cured by microwave energy", Contemp Clin Dent, 4, pp.147~151 (2013)
- Anusavice K, "Phillips’ Science of Dental Materials" (2012), Saunders
- Hada T, "Effect of printing direction on the accuracy of 3D-printed dentures using stereolithography technology", Materials, 13, pp.e3405~ (2020)
- Kattadiyil MT, "CAD", CAM complete dentures : a review of two commercial fabrication systems, 2013, pp.41, 407~416
- Chen J, "Shape optimization for additive manufacturing of removable partial dentures-A new paradigm for prosthetic CAD", CAM, 2015, pp.10, e0132552~
- 고은솔, "Color stability of three dimensional-printed denture teeth exposed to various colorants", 대한치과보철학회지, 58(1), pp.1~6 (2020), 대한치과보철학회[DOI]
- Revilla-León M, "Additive manufacturing technologies used for processing polymers : Current status and potential application in prosthetic dentistry", J Prosthodont, 28, pp.146~158 (2019)
- Shinawi LA, "Effect of denture cleaning on abrasion resistance and surface topography of polymerized CAD CAM acrylic resin denture base", Electron Physician, 9, pp.4281~4288 (2017)
- Sorgini DB, "Abrasiveness of conventional and specific denture-cleansing dentifrices", Braz Dent J, 23, pp.154~159 (2012)
- Pellizzaro D, "Effectiveness of mechanical brushing with different denture cleansing agents in reducing in vitro Candida albicans biofilm viability", Braz Dent J, 23, pp.547~554 (2012)
- de Andrade IM, "Trial of experimental toothpastes regarding quality for cleaning dentures", Int J Prosthodont, 25, pp.157~159 (2012)
- de Freitas Pontes KM, "Effect of toothbrushes and denture brushes on heat-polymerized acrylic resins", Gen Dent, 64, pp.49~53 (2016)
- Dyer D, "Abrasion and stain removal by different manual toothbrushes and brush actions : studies in vitro", J Clin Periodontol, 28, pp.121~127 (2001)
- Hersek N, "Color stability of denture base acrylic resins in three food colorants", J Prosthet Dent, 81, pp.375~379 (1999)
- Erdemir U, "Effects of energy and sports drinks on tooth structures and restorative materials", World J Stomatol, 5, pp.1~7 (2016)
- Chung YJ, "3D printing of resin material for denture artificial teeth: chipping and indirect tensile fracture resistance", Materials(Basel), 11, pp.1798~ (2018)
- Gale MS, "Thermal cycling procedures for laboratory testing of dental restorations", J Dent, 27, pp.89~99 (1999)
- Sorgini DB, "Adverse effects on PMMA caused by mechanical and combined methods of denture cleansing", Braz Dent J, 26, pp.292~296 (2015)
- Van Leeuwen MPC, "Toothbrush wear in relation to toothbrushing effectiveness", Int J Dent Hyg, 17, pp.77~84 (2019)
- Al Amri MD, "In vitro evaluation of translucency and color stability of CAD", CAM polymer-infiltrated ceramic materials after accelerated aging, 2021, pp.30, 318~328
- Klimek J, "Fluoride taken up by plaque, by the underlying enamel and by clean enamel from three fluoride compounds in vitro", Caries Res, 16, pp.156~161 (1982)
- Guler AU, "Effects of different drinks on stainability of resin composite provisional restorative materials", J Prosthet Dent, 94, pp.118~124 (2005)
- Chang JY, "Evaluating the accuracy of tooth color measurement by combining the Munsell color system and dental colorimeter", Kaohsiung J Med Sci, 28, pp.490~494 (2012)
- "ISO/TR-28642. Dentistry-guidance on colour measurments" (2016)[URL]
- Judd DB, "Physiological optics at the national bureau of standards", Appl Opt, 6, pp.13~26 (1967)
- 송소연, "Physical properties and color stability of injection-molded thermoplastic denture base resins", The Journal of Advanced of Prosthodontics, 11(1), pp.32~40 (2019), 대한치과보철학회[DOI]
- Goldstein GR, "Repeatability of a specially designed intraoral colorimeter", J Prosthet Dent, 69, pp.616~619 (1993)
- Morresi AL, "Thermal cycling for restorative materials : does a standardized protocol exist in laboratory testing? a literature review", J Mech Behav Biomed Mater, 29, pp.295~308 (2014)
- Eliasson ST, "Effect of thermal cycling on temperature changes and bond strength in different test specimens", Biomater Investig Dent, 7, pp.16~24 (2020)
- Silva Cde S, "Effect of thermal cycling on denture base and autopolymerizing reline resins", J Appl Oral Sci, 21, pp.219~224 (2013)
- Hollis S, "Color stability of denture resins after staining and exposure to cleansing agents", J Prosthet Dent, 114, pp.709~714 (2015)
- Bezgin T, "Effect of toothbrushing on color changes of esthetic restorative materials", J Esthet Restor Dent, 27, pp.S65~S73 (2015)
- Buyukyilmaz S, "Color stability of denture base polymers", Int J Prosthodont, 7, pp.372~382 (1994)
- Keskin S, "The treatment of prosthetic dental materials withhypchlorite", pp.2002
- Imirzalioglu P, "Color stability of denture acrylic resins and a soft lining material against tea, coffee, and nicotine", J Prosthodont, 19, pp.118~124 (2010)
- Buchalla W, "The effect of water storage and light exposure on the color and translucency of a hybrid and a microfilled composite", J Prosthet Dent, 87, pp.264~270 (2002)
- Bagheri R, "Influence of food-simulating solutions and surface finish on susceptibility to staining of aesthetic restorative materials", J Dent, 33, pp.389~398 (2005)
- Shin JW, "Evaluation of the color stability of 3D-printed crown and bridge materials against various sources of discoloration: an in vitro study", Materials(Basel), 13, pp.5359~ (2020)
- Berli C, "Comparing the mechanical properties of pressed, milled, and 3D-printed resins for occlusal devices", J Prosthet Dent, 124, pp.780~786 (2020)
- Omata Y, "Staining of hybrid composites with coffee, oolong tea, or red wine", Dent Mater J, 25, pp.125~131 (2006)
- Nimeroff I, "Colorimetry. National Bureau of Standards Monograph 104", U.S. Dept. of Commerce, National Bureau of Standards, ~ (1968)
- Chang YH, "Effect of toothbrush", dentifrice abrasion on weight variation, surface roughness, surface morphology and hardness of conventional and CAD, Dent Mater J, pp.2021, 40[DOI]
- Sandro Basso Bitencourt, "Effect of acidic beverages on surface roughness and color stability of artificial teeth and acrylic resin", The Journal of Advanced of Prosthodontics, 12(2), pp.55~60 (2020), 대한치과보철학회[DOI]