The effect of the digital manufacturing technique of cantilevered implant-supported frameworks on abutment screw preload
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
PURPOSE. The purpose of this study was to investigate the misfit and screw preload at the implant abutment connection of implant supported fixeddental prosthesis with cantilever (ICFDP) manufactured using different digital manufacturing techniques and to compare the screw preload before and after cyclic loading. MATERIALS AND METHODS. Mandibular jaw model with four intra-foraminal implants was scanned using digital scanner. Stereolithography file was used to design a framework with nonengaging (NE) abutments and 10 mm cantilever distal to one terminal implant. Five frameworks were constructed using combined digital-conventional techniques (CAD-cast), and five frameworks were constructed using three-dimensional printing (3DP). Additional CAD-cast framework was constructed in a way that ensures passive fit (PF) to use as control. Scanning electron microscope (SEM) measured the implant abutment connection misfit. Sixty screws were used on the corresponding frameworks. Screws were torqued and pre-cyclic loading reverse torque value (RTV) was recorded. Frameworks were subjected to 200,000 loading cycles with a loading point 9 mm from the center of terminal implants adjacent to the cantilever and post-cyclic loading RTVs were recorded. RESULTS. Microscopic readings showed significant differences between frameworks. PF demonstrated the lowest measurements of 16.04 (2.6) μm while CAD-cast demonstrated the highest measurements of 29.2 (3.1) μm. In all groups, RTVs were significantly lower than the applied torque. Post-cyclic loading RTV was significantly lower than pre-cyclic loading RTV in PF and 3DP frameworks. Differences in RTVs between the three manufacturing techniques were insignificant. CONCLUSION. Although CAD-cast and threedimensionally printed (3DP) both produce frameworks with clinically acceptable misfit, 3DP might not be the technique of choice for maintaining screw’s preload stability under an aggressive loading situation.
Abstract
PURPOSE. The purpose of this study was to investigate the misfit and screw preload at the implant abutment connection of implant supported fixeddental prosthesis with cantilever (ICFDP) manufactured using different digital manufacturing techniques and to compare the screw preload before and after cyclic loading. MATERIALS AND METHODS. Mandibular jaw model with four intra-foraminal implants was scanned using digital scanner. Stereolithography file was used to design a framework with nonengaging (NE) abutments and 10 mm cantilever distal to one terminal implant. Five frameworks were constructed using combined digital-conventional techniques (CAD-cast), and five frameworks were constructed using three-dimensional printing (3DP). Additional CAD-cast framework was constructed in a way that ensures passive fit (PF) to use as control. Scanning electron microscope (SEM) measured the implant abutment connection misfit. Sixty screws were used on the corresponding frameworks. Screws were torqued and pre-cyclic loading reverse torque value (RTV) was recorded. Frameworks were subjected to 200,000 loading cycles with a loading point 9 mm from the center of terminal implants adjacent to the cantilever and post-cyclic loading RTVs were recorded. RESULTS. Microscopic readings showed significant differences between frameworks. PF demonstrated the lowest measurements of 16.04 (2.6) μm while CAD-cast demonstrated the highest measurements of 29.2 (3.1) μm. In all groups, RTVs were significantly lower than the applied torque. Post-cyclic loading RTV was significantly lower than pre-cyclic loading RTV in PF and 3DP frameworks. Differences in RTVs between the three manufacturing techniques were insignificant. CONCLUSION. Although CAD-cast and threedimensionally printed (3DP) both produce frameworks with clinically acceptable misfit, 3DP might not be the technique of choice for maintaining screw’s preload stability under an aggressive loading situation.
참고문헌 (49)
- Storelli S, "Implant supported cantilevered fixed dental rehabilitations in partially edentulous patients:Systematic review of the literature. Part I", Clin Oral Implants Res, 29, pp.253~274 (2018)
- Schmid E, "Clinical and radiographic outcomes of implant-supported fixed dental prostheses with cantilever extension. A retrospective cohort study with a follow-up of at least 10 years", Clin Oral Implants Res, 31, pp.1243~1252 (2020)
- Storelli S, "Implant-supported cantilevered fixed dental rehabilitations in fully edentulous patients: systematic review of the literature. Part II", Clin Oral Implants Res, 29, pp.275~294 (2018)
- Hämmerle CHF, "Biomechanical aspects: summary and consensus statements of group 4. The 5th EAO Consensus Conference 2018", Clin Oral Implants Res, 29, pp.326~331 (2018)
- Romeo E, "Systematic review of the survival rate and the biological, technical, and aesthetic complications of fixed dental prostheses with cantilevers on implants reported in longitudinal studies with a mean of 5 years follow-up", Clin Oral Implants Res, 23, pp.39~49 (2012)
- Purcell BA, "Anteroposterior spread and cantilever length in mandibular metal-resin implant-fixed complete dental prostheses : a 7-to 9-year analysis", Int J Prosthodont, 28, pp.512~518 (2015)
- Aglietta M, "A systematic review of the survival and complication rates of implant supported fixed dental prostheses with cantilever extensions after an observation period of at least 5 years", Clin Oral Implants Res, 20, pp.441~451 (2009)
- Sánchez-Torres A, "Mechanical complications of implant-supported complete-arch restorations and impact on patient quality of life : A retrospective cohort study", J Prosthet Dent, 125, pp.279~286 (2021)
- Fischer K, "Prospective 10-year cohort study based on a randomized, controlled trial (RCT)on implant-supported full-arch maxillary prostheses. part II: prosthetic outcomes and maintenance", Clin Implant Dent Relat Res, 15, pp.498~508 (2013)
- Chochlidakis K, "Survival rates and prosthetic complications of implant fixed complete dental prostheses : an up to 5-year retrospective study", J Prosthet Dent, 124, pp.539~546 (2020)
- Vinhas AS, "Review of the mechanical behavior of different implant-abutment connections", Int J Environ Res Public Health, 17, pp.8685~ (2020)
- Yilmaz B, "Screw stability of CAD-CAM titanium and zirconia abutments on different implants : an in vitro study", Clin Implant Dent Relat Res, 23, pp.373~379 (2021)
- Azam Sadat Mostafavi, "Effect of fluid contamination on reverse torque values in implant-abutment connections under oral conditions", The Journal of Advanced of Prosthodontics, 13(1), pp.65~70 (2021), 대한치과보철학회[DOI]
- Hu E, "Effect of screw channel angulation on reverse torque values of dental implant abutment screws", J Prosthodont, 28, pp.969~972 (2019)
- Ki-Young Lee, "Clinical study on screw loosening in dental implant prostheses: a 6-year retrospective study", 대한구강악안면외과학회지, 46(2), pp.133~142 (2020), 대한구강악안면외과학회[DOI]
- Huang Y, "Mechanism of and factors associated with the loosening of the implant abutment screw : a review", J Esthet Restor Dent, 31, pp.338~345 (2019)
- Kourtis S, "Loosening of the fixing screw in single implant crowns: predisposing factors, prevention and treatment options", J Esthet Restor Dent, 29, pp.233~246 (2017)
- Benjaboonyazit K, "Removal torque pattern of a combined cone and octalobule index implant-abutment connection at different cyclic loading : an in-vitro experimental study", Int J Implant Dent, 5, pp.1~ (2019)
- Al-Otaibi HN, "The effect of torque application technique on screw preload of implant-supported prostheses", Int J Oral Maxillofac Implants, 32, pp.259~263 (2017)
- Siadat H, "Effect of lateral oblique cyclic loading on microleakage and screw loosening of implants with different connections", J Dent Res Dent Clin Dent Prospects, 12, pp.183~189 (2018)
- Jivraj S, "Material considerations for full-arch implant-supported restorations", pp.189~211 (2018), Springer International Publishing
- Han X, "Comparative analysis of mechanical properties and metal-ceramic bond strength of Co-Cr dental alloy fabricated by different manufacturing processes", Materials(Basel), 11, pp.1801~ (2018)
- Koutsoukis T, "Selective laser melting technique of Co-Cr dental alloys : a review of structure and properties and comparative analysis with other available techniques", J Prosthodont, 24, pp.303~312 (2015)
- Revilla-León M, "A review of the applications of additive manufacturing technologies used to fabricate metals in implant dentistry", J Prosthodont, 29, pp.579~593 (2020)
- Ramalho I, "Influence of abutment fabrication method on 3D fit at the implant-abutment connection", Int J Prosthodont, 33, pp.641~647 (2020)
- Rekow ED, "Digital dentistry : The new state of the art-Is it disruptive or destructive?", Dent Mater, 36, pp.9~24 (2020)
- Uribarri A, "Marginal and internal fit of CAD", CAM frameworks in multiple implant-supported restorations : scanning and milling error analysis, 2019, pp.21, 1062~1072
- Abduo J, "Trends in computer-aided manufacturing in prosthodontics : a review of the available streams", Int J Dent, 2014, pp.783948~ (2014)
- Presotto AGC, "Feasibility of 3D printed Co-Cr alloy for dental prostheses applications", J Alloys Compounds, 862, pp.158171~ (2021)
- Joda T, "The complete digital workflow in fixed prosthodontics : a systematic review", BMC Oral Health, 17, pp.124~ (2017)
- Ramalho IS, "Implant-abutment fit influences the mechanical performance of single-crown prostheses", J Mech Behav Biomed Mater, 102, pp.103506~ (2020)
- Bae S, "Reliability of metal 3D printing with respect to the marginal fit of fixed dental prostheses: a systematic review and meta-analysis", Materials(Basel), 13, pp.4781~ (2020)
- El-Sheikh MAY, "Effect of different angulations and collar lengths of conical hybrid implant abutment on screw loosening after dynamic cyclic loading", Int J Implant Dent, 4, pp.39~ (2018)
- Paepoemsin T, "Removal torque evaluation of three different abutment screws for single implant restorations after mechanical cyclic loading", Oral Implantol, 9, pp.213~221 (2016)
- Savignano R, "Computational biomechanical analysis of engaging and nonengaging abutments for implant screw-retained fixed dental prostheses", J Prosthodont, 30, pp.604~609 (2021)
- Hecker DM, "Cyclic loading of implant-supported prostheses : comparison of gaps at the prosthetic-abutment interface when cycled abutments are replaced with as-manufactured abutments", J Prosthet Dent, 95, pp.26~32 (2006)
- Padrós R, "Mechanical properties of CoCr dental-prosthesis restorations made by three manufacturing processes. Influence of the microstructure and topography", Metals, 10, pp.788~ (2020)
- Katsoulis J, "Misfit of implant prostheses and its impact on clinical outcomes. Definition, assessment and a systematic review of the literature", Eur J Oral Implantol, 10, pp.121~138 (2017)
- Revilla-León M, "Implant prosthodontic discrepancy of complete-arch Co-Cr implant frameworks manufactured through selective laser melting additive manufacturing technology using a coordinate measuring machine", Int J Oral Maxillofac Implants, 34, pp.698~707 (2019)
- Presotto AGC, "Dimensional precision of implant-supported frameworks fabricated by 3D printing", J Prosthet Dent, 122, pp.38~45 (2019)
- Gonzalo E, "Evaluation of milled titanium versus laser sintered Co-Cr abutments on the marginal misfit in internal implant-abutment connection", Materials(Basel), 13, pp.4873~ (2020)
- Rutkūnas V, "Comparison of conventional and digital workflows for implant-supported screw-retained zirconia FPD bars:Fit and cement gap evaluation using SEM analysis", Int J Oral Implantol(Berl), 14, pp.199~210 (2021)
- Pan Y, "Implant framework misfit : A systematic review on assessment methods and clinical complications", Clin Implant Dent Relat Res, 23, pp.244~258 (2021)
- Yao KT, "Mechanical performance of conical implant-abutment connections under different cyclic loading conditions", J Mech Behav Biomed Mater, 90, pp.426~432 (2019)
- Arshad M, "Effect of repeated screw joint closing and opening cycles and cyclic loading on abutment screw removal torque and screw thread morphology : scanning electron microscopy evaluation", Int J Oral Maxillofac Implants, 33, pp.31~40 (2018)
- Tiossi R, "Influence of cyclic fatigue in water on screw torque loss of long-span one-piece implant-supported zirconia frameworks", J Prosthodont, 26, pp.315~320 (2017)
- Delben JA, "Evaluation of the effect of retightening and mechanical cycling on preload maintenance of retention screws", Int J Oral Maxillofac Implants, 26, pp.251~256 (2011)
- Yuseung Yi, "Comparison of CAD", CAM abutment and prefabricated abutment in Morse taper internal type implant after cyclic loading: Axial displacement, removal torque, and tensile removal force, 2019, pp.11(6), 305~312[DOI]
- Revilla-León M, "A review of the applications of additive manufacturing technologies used to fabricate metals in implant dentistry", J Prosthodont, 29, pp.579~593 (2020)