The role of internal architecture in producing high-strength 3D printed cobaltchromium objects
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Purpose. The objectives of the current study were to estimate the influence of self-reinforced hollow structures with a graded density on the dimensional accuracy, weight, and mechanical properties of Co-Cr objects printed with the direct metal laser sintering (DMLS) technique. Materials and methods. Sixty-five dog-bone samples were manufactured to evaluate the dimensional accuracy of printing, weight, and tensile properties of DMLS printed Co-Cr. They were divided into Group 1 (control) (n = 5), Group 2, 3, and 4 with incorporated hollow structures based on (spherical, elliptical, and diamond) shapes; they were subdivided into subgroups (n = 5) according to the volumetric reduction (10%, 15%, 20% and 25%). Radiographic imaging and microscopic analysis of the fractographs were conducted to validate the created geometries; the dimensional accuracy, weight, yield tensile strength, and modulus of elasticity were calculated. The data were estimated by one-way ANOVA and Duncan’s tests at P < .05. Results. The accuracy test showed an insignificant difference in the x, y, z directions in all printed groups. The weight was significantly reduced proportionally to the reduced volume fraction. The yield strength and elastic modulus of the control group and Group 2 at 10% volume reduction were comparable and significantly higher than the other subgroups. Conclusion. The printing accuracy was not affected by the presence or type of the hollow geometry. The weight of Group 2 at 10% reduction was significantly lower than that of the control group. The yield strength and elastic modulus of the Group 2 at a 10% reduction showed means equivalent to the compact objects and were significantly higher than other subgroups.
Abstract
Purpose. The objectives of the current study were to estimate the influence of self-reinforced hollow structures with a graded density on the dimensional accuracy, weight, and mechanical properties of Co-Cr objects printed with the direct metal laser sintering (DMLS) technique. Materials and methods. Sixty-five dog-bone samples were manufactured to evaluate the dimensional accuracy of printing, weight, and tensile properties of DMLS printed Co-Cr. They were divided into Group 1 (control) (n = 5), Group 2, 3, and 4 with incorporated hollow structures based on (spherical, elliptical, and diamond) shapes; they were subdivided into subgroups (n = 5) according to the volumetric reduction (10%, 15%, 20% and 25%). Radiographic imaging and microscopic analysis of the fractographs were conducted to validate the created geometries; the dimensional accuracy, weight, yield tensile strength, and modulus of elasticity were calculated. The data were estimated by one-way ANOVA and Duncan’s tests at P < .05. Results. The accuracy test showed an insignificant difference in the x, y, z directions in all printed groups. The weight was significantly reduced proportionally to the reduced volume fraction. The yield strength and elastic modulus of the control group and Group 2 at 10% volume reduction were comparable and significantly higher than the other subgroups. Conclusion. The printing accuracy was not affected by the presence or type of the hollow geometry. The weight of Group 2 at 10% reduction was significantly lower than that of the control group. The yield strength and elastic modulus of the Group 2 at a 10% reduction showed means equivalent to the compact objects and were significantly higher than other subgroups.
참고문헌 (49)
- Steuben JC, "Towards multiscale topology optimization for additively manufactured components using implicit slicing", International design engineering technical conferences and computers and information in engineering conference (2017), American Soc Mech Engi
- Khorsandi D, "3D and 4D printing in dentistry and maxillofacial surgery : Printing techniques, materials, and applications", Acta Biomater, 122, pp.26~49 (2021)
- Kränzlin N, "Controlled fabrication of porous metals from the nanometer to the macroscopic scale", Mater Horiz, 4, pp.359~377 (2015)
- Plocher J, "Review on design and structural optimisation in additive manufacturing : Towards next-generation lightweight structures", Mater Des, 183, pp.108164~ (2019)
- Babamiri B, "Designing additively manufactured lattice structures based on deformation mechanisms", Addit Manuf, 46, pp.102143~ (2021)
- Zhu JH, "Topology optimization in aircraft and aerospace structures design", Arch Comput Methods Eng, 23, pp.595~622 (2016)
- Kladovasilakis N, "Architected materials for additive manufacturing : a comprehensive review", Materials, 15, pp.5919~ (2022)
- Abueidda DW, "Mechanical properties of 3D printed polymeric cellular materials with triply periodic minimal surface architectures", Mater Des, 122, pp.255~267 (2017)
- Al-Saedi DSJ, "Mechanical properties and energy absorption capability of functionally graded F2BCC lattice fabricated by SLM", Mater Des, 144, pp.32~44 (2018)
- Xiao Z, "Evaluation of topology-optimized lattice structures manufactured via selective laser melting", Mater Des, 143, pp.27~37 (2018)
- Gu DD, "Laser additive manufacturing of metallic components : materials, processes and mechanisms", Int Mater Rev, 57, pp.133~164 (2012)
- Paper R, "Investigation of metallic 3D porous scaffold prepared by selective laser sintering for dental applications", Nanochem Res, 8, pp.122~133 (2023)
- Goh GD, "A review on machine learning in 3D printing : applications, potential, and challenges", Artificial Intelligence Rev, 54, pp.63~94 (2021)
- Koutsoukis T, "Selective laser melting technique of Co-Cr dental alloys : a review of structure and properties and comparative analysis with other available techniques", J Prosthodont, 24, pp.303~312 (2015)
- Huang R, "Cost minimization in metal additive manufacturing using concurrent structure and process optimization", International design engineering technical conferences and computers and information in engineering conference (2017), American Soc Mech Eng
- Galeta T, "Influence of structure on mechanical properties of 3D printed objects", Procedia Eng, 149, pp.100~104 (2016)
- Challis VJ, "Design of three dimensional isotropic microstructures for maximized stiffness and conductivity", Int J Solids Struct, 45, pp.4130~4146 (2008)
- Lesueur M, "Predicting the yield strength of a 3D printed porous material from its internal geometry", Addit Manuf, 44, pp.102061~ (2021)
- "ISO 22674. Metallic materials for fixed and removable restorations and appliances", International Standards Organization (ISO), ~ (2016)
- "ASTM Committee E28. ASTM E9-89a. Stand test methods compression test met mater room temp", 1~9 (2000)
- Xiong Y, "A new approach to eliminating enclosed voids in topology optimization for additive manufacturing", Addit Manuf, 32, pp.101006~ (2020)
- MacKenzie JK, "The elastic constants of a solid containing spherical holes", Proc Phys Soc Sect B, 63, pp.2~11 (1950)
- Sas W, "Impact of the stabilization of compacted cohesive soil-sandy clayon yield criterion improvement", Ann Warsaw Univ Life Sci L Reclam, 46, pp.139~151 (2014)
- Smith I, "Load and resistance factor design of timber joints : International practice and future direction", J Struct Eng, 128, pp.48~59 (2002)
- Zupancic R, "Tensile strength and corrosion resistance of brazed and laser-welded cobalt-chromium alloy joints", J Prosthet Dent, 96, pp.273~282 (2006)
- Unkovskiy A, "Objects build orientation, positioning, and curing influence dimensional accuracy and flexural properties of stereolithographically printed resin", Dent Mater, 34, pp.e324~e333 (2018)
- Islam MN, "An investigation of dimensional accuracy of parts produced by three-dimensional printing", Proceedings of the World Congress on Engineering 2013, pp.522~525 (2013), IAENG
- Hällgren S, "3D data export for additive manufacturing-improving geometric accuracy", Procedia Cirp, 50, pp.518~523 (2016)
- Peng PW, "Trueness of removable partial denture frameworks additively manufactured with selective laser melting", J Prosthet Dent, 127, pp.122~127 (2022)
- Okano H, "Effects of hollow structures added by selective laser sintering on the mechanical properties of Co-Cr alloy", J Prosthodont Res, 67, pp.460~467 (2023)
- Kocak EF, "Effect of internal design modification on the mechanical properties of laser sintered cobalt-chromium multi-unit metal-ceramic frameworks", J Prosthodont, 31, pp.766~770 (2022)
- Chiu LNS, "Effect of stiffness anisotropy on topology optimisation of additively manufactured structures", Eng Struct, 171, pp.842~848 (2018)
- Orme ME, "Designing for additive manufacturing : Lightweighting through topology optimization enables lunar spacecraft", J Mech Des Trans ASME, 139, pp.100905~100906 (2017)
- Conway K, "Increasing fracture toughness via architected porosity", Mater Des, 205, pp.109696~ (2021)
- Al-Ketan O, "On mechanical properties of cellular steel solids with shell-like periodic architectures fabricated by selective laser sintering", J Eng Mater Technol Trans ASME, 141, pp.021009~ (2019)
- Liu YJ, "Enhanced fatigue characteristics of a topology-optimized porous titanium structure produced by selective laser melting", Addit Manuf, 32, pp.101060~ (2020)
- Challis VJ, "High specific strength and stiffness structures produced using selective laser melting", Mater Des, 63, pp.783~788 (2014)
- Takezawa A, "High-stiffness and strength porous maraging steel via topology optimization and selective laser melting", Addit Manuf, 18, pp.194~202 (2017)
- Yoder S, "Characterization of topology optimized Ti-6Al-4V components using electron beam powder bed fusion", Addit Manuf, 19, pp.184~196 (2018)
- Al-Ketan O, "Topology-mechanical property relationship of 3D printed strut, skeletal, and sheet based periodic metallic cellular materials", Addit Manuf, 19, pp.167~183 (2018)
- Ferro P, "Porosity inducing process parameters in selective laser melted AlSi10Mg aluminium alloy", Phys Mesomech, 23, pp.256~262 (2020)
- Geiger F, "Tailoring the texture of IN-738LC processed by selective laser melting(SLM)by specific scanning strategies", Mater Sci Eng A, 661, pp.240~246 (2016)
- Pellizzari M, "A 3D-printed ultra-low young’s modulus β-Ti alloy for biomedical applications", Materials, 13, pp.2792~ (2020)
- Etter T, "IOP Conference Series: Materials Science and Engineering", pp.12097~ (2015), IOP Publishing
- Astuti ER, "Computer-aided system of the mandibular cortical bone porosity assessment on digital panoramic radiographs", Eur J Dent, 17, pp.464~471 (2023)
- Putri TS, "Fabrication of three-dimensional interconnected porous blocks composed of robust carbonate apatite frameworks", Ceram Int, 46, pp.20045~20049 (2020)
- Song J, "Topology optimization-guided lattice composites and their mechanical characterizations", Compos Part B Eng, 160, pp.402~411 (2019)
- Maconachie T, "SLM lattice structures : Properties, performance, applications and challenges", Mater Des, 183, pp.108137~ (2019)
- Vilardell AM, "Topology optimization and characterization of Ti6Al4V ELI cellular lattice structures by laser powder bed fusion for biomedical applications", Mater Sci Eng A, 766, pp.138330~ (2019)