Color stability of fully- and pre-crystalized chair-side CAD-CAM lithium disilicate restorations after required and additional sintering processes
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
PURPOSE. The aim of this study was to investigate shade changes in fully- and pre-crystalized CAD-CAM lithium disilicate crowns after the required and additional firing processes. MATERIALS AND METHODS. One hundred and five crowns of shade A1 with high translucency were milled out of CAD-CAM lithium disilicate blocks and categorized as follows (n = 15): (1) restorations fabricated from Straumann n!ce with no additional sintering process; (2) restorations fabricated from Straumann n!ce with one additional sintering process; (3) restorations fabricated from Straumann n!ce with two additional sintering processes; (4) restorations fabricated from Amber Mill with one sintering process; (5) restorations fabricated from Amber Mill with two sintering processes; (6) restorations fabricated from IPS e.max CAD with one sintering process; (7) restorations fabricated from IPS e.max CAD with two sintering processes. All restorations were evaluated with a color imaging spectrophotometer. RESULTS. All restorations presented some color alteration from the original shade both after a single and after two firing processes. CONCLUSION. The required and additional sintering processes for restorations fabricated with chairside CAD-CAM lithium disilicate blocks cause an alteration of the original shade selected. Shade A1 high translucency restorations tend to change to a more yellowish B1 shade after a sintering process.
Abstract
PURPOSE. The aim of this study was to investigate shade changes in fully- and pre-crystalized CAD-CAM lithium disilicate crowns after the required and additional firing processes. MATERIALS AND METHODS. One hundred and five crowns of shade A1 with high translucency were milled out of CAD-CAM lithium disilicate blocks and categorized as follows (n = 15): (1) restorations fabricated from Straumann n!ce with no additional sintering process; (2) restorations fabricated from Straumann n!ce with one additional sintering process; (3) restorations fabricated from Straumann n!ce with two additional sintering processes; (4) restorations fabricated from Amber Mill with one sintering process; (5) restorations fabricated from Amber Mill with two sintering processes; (6) restorations fabricated from IPS e.max CAD with one sintering process; (7) restorations fabricated from IPS e.max CAD with two sintering processes. All restorations were evaluated with a color imaging spectrophotometer. RESULTS. All restorations presented some color alteration from the original shade both after a single and after two firing processes. CONCLUSION. The required and additional sintering processes for restorations fabricated with chairside CAD-CAM lithium disilicate blocks cause an alteration of the original shade selected. Shade A1 high translucency restorations tend to change to a more yellowish B1 shade after a sintering process.
참고문헌 (20)
- Tsujimoto A, "Influence of thermal cycling on flexural properties and simulated wear of computer-aided design", computer-aided manufacturing resin composites, 2017, pp.42, 101~110
- Jurado Carlos Alberto, "Chair-side CAD", CAM fabrication of a single-retainer resin bonded fixed dental prosthesis: a case report, 2020, pp.45(2), 1~7[DOI]
- Christensen GJ, "Is the rush to all-ceramic crowns justified?", J Am Dent Assoc, 145, pp.192~194 (2014)
- Makhija SK, "Dentist material selection for single-unit crowns : findings from the National Dental Practice-Based Research Network", J Dent, 55, pp.40~47 (2016)
- Albakry M, "Influence of hot pressing on the microstructure and fracture toughness of two pressable dental glass-ceramics", J Biomed Mater Res B Appl Biomater, 71, pp.99~107 (2004)
- Yin R, "Comparative evaluation of mechanical properties and wear ability of five CAD", CAM dental blocks, 2019, pp.12, 2252~
- Stawarczyk B, "Modern CAD", CAM silicate ceramics, their translucency level and impact of hydrothermal aging on translucency, Martens hardness, biaxial flexural strength and their reliability, 2021, pp.118, 104456~
- Verena Preis, "In vitro performance and fracture resistance of novel CAD", CAM ceramic molar crowns loaded on implants and human teeth, 2018, pp.10(4), 300~307[DOI]
- Kanat-Ertürk B, "Color stability of CAD", CAM ceramics prepared with different surface finishing procedures, 2020, pp.29, 166~172
- Kurt M, "Effects of glazing methods on the optical and surface properties of silicate ceramics", J Prosthodont Res, 64, pp.202~209 (2020)
- Wee AG, "Contemporary Fixed Prosthodontics", pp.709~732 (2006), Mosby
- Cal E, "Application of a digital technique in evaluating the reliability of shade guides", J Oral Rehabil, 31, pp.483~491 (2004)
- Berns RS, "Billmeyer and Saltzman’s principles of color technology", pp.13~20 (2019), John Wiley & Sons
- Paul SJ, "Conventional visual vs spectrophotometric shade taking for porcelain-fused-to-metal crowns : a clinical comparison", Int J Periodontics Restorative Dent, 24, pp.222~231 (2004)
- Acar O, "Color stainability of CAD", CAM and nanocomposite resin materials, 2016, pp.115, 71~75
- Cui H, "Effect of repeated sintering and variations in thickness on the color and microstructure of dental lithium disilicate-based glass ceramic veneers", West China J Stomatol, 35, pp.389~393 (2017)
- Turgut S, "Effect of resin cement and ceramic thickness on final color of laminate veneers : an in vitro study", J Prosthet Dent, 109, pp.179~186 (2013)
- 김성준, "Color changes of ceramic veneers following glazing with respect to their composition", The Journal of Advanced of Prosthodontics, 11(1), pp.16~22 (2019), 대한치과보철학회[DOI]
- Li Q, "Effects of Luting Composites on the Resultant Colors of Ceramic Veneers to Intended Shade Tab", J Prosthodont, 28, pp.327~331 (2019)
- Ozdogan A, "Effects of multiple firing processes on the mechanical properties of lithium disilicate glass-ceramics produced by two different production techniques", J Prosthet Dent, 125, pp.527~ (2021)