Color changes of monolithic zirconia block before and after sintering
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
The aim of this study was to compare the color changes of three monolithic zirconia blocks by two shades before and after sintering. A total of 60 cuboid-shaped HT (H) and A2 (A) shade zirconia specimens (8.0×8.0×5.0 mm) were fabricated for the following materials: Razor (RZ) (RZ_H, RZ_A), Zenotec (ZN) (ZN_H, ZN_A), and Anatomic Coloured (AC) (AC_H, AC_A). A spectrophotometer was used to measure color coordinates (Commission Internationale de l'Eclairage [CIE] L*a*b*) before sintering. Sintering was done in the same condition. The color after sintering was evaluated, and color differences (ΔE*) before and after sintering were calculated. For comparisons, statistical analyses were conducted using a one-way analysis of variance (α=0.05). The ΔE* of the HT shade was significantly higher in the RZ_H (19.29±0.49) and AC_H (19.37±0.25) than in ZN_H (14.11±0.28). The ΔE* of A2 shade showed statistically significant difference in all groups, with RZ_A being the highest (28.39±0.51), followed by AC_A (23.01±0.43) and ZN_A (21.12±0.85). All materials had the largest ΔL* with decreasing direction. It indicated that the specimen darkened after sintering. The ΔL* in all materials was larger in the A2 group than in the HT group, and ΔE* was also larger in the A2 group. Within the limitations of this study, we conclude that after sintering of zirconia, the color change was the greatest in lightness, and the degree and pattern of change were different depending on the material and shade.
Abstract
The aim of this study was to compare the color changes of three monolithic zirconia blocks by two shades before and after sintering. A total of 60 cuboid-shaped HT (H) and A2 (A) shade zirconia specimens (8.0×8.0×5.0 mm) were fabricated for the following materials: Razor (RZ) (RZ_H, RZ_A), Zenotec (ZN) (ZN_H, ZN_A), and Anatomic Coloured (AC) (AC_H, AC_A). A spectrophotometer was used to measure color coordinates (Commission Internationale de l'Eclairage [CIE] L*a*b*) before sintering. Sintering was done in the same condition. The color after sintering was evaluated, and color differences (ΔE*) before and after sintering were calculated. For comparisons, statistical analyses were conducted using a one-way analysis of variance (α=0.05). The ΔE* of the HT shade was significantly higher in the RZ_H (19.29±0.49) and AC_H (19.37±0.25) than in ZN_H (14.11±0.28). The ΔE* of A2 shade showed statistically significant difference in all groups, with RZ_A being the highest (28.39±0.51), followed by AC_A (23.01±0.43) and ZN_A (21.12±0.85). All materials had the largest ΔL* with decreasing direction. It indicated that the specimen darkened after sintering. The ΔL* in all materials was larger in the A2 group than in the HT group, and ΔE* was also larger in the A2 group. Within the limitations of this study, we conclude that after sintering of zirconia, the color change was the greatest in lightness, and the degree and pattern of change were different depending on the material and shade.
참고문헌 (22)
- 조준호, "치과용 지르코니아 블록의 소결온도가 기계적 특성과 미세구조에 미치는 영향", 대한치과기공학회지, 36(1), pp.9~15 (2014), 대한치과기공학회[DOI]
- Juntavee N, "Influence of thermal tempering processes on color characteristics of different monolithic computer-assisted design and computer-assisted manufacturing ceramic materials", J Clin Exp Dent, 11, pp.e614~e624 (2019)[DOI]
- 공문천, "착색액 침지 횟수와 최종 소결 온도가 지르코니아 세라믹의 굴곡강도에 미치는 영향", 대한치과재료학회지, 44(2), pp.171~178 (2017), 대한치과재료학회[DOI]
- Sen N, "Microstructural, physical, and optical characterization of high-translucency zirconia ceramics", J Prosthet Dent, 123, pp.761~768 (2020)[DOI]
- Stawarczyk B, "The effect of zirconia sintering temperature on flexural strength, grain size, and contrast ratio", Clin Oral Investig, 17, pp.269~274 (2013)[DOI]
- 김미진, "Effects of the sintering conditions of dental zirconia ceramics on the grain size and translucency", The Journal of Advanced of Prosthodontics, 5(2), pp.161~166 (2013), 대한치과보철학회[DOI]
- Ebeid K, "Effect of changes in sintering parameters on monolithic translucent zirconia", Dent Mater, 30, pp.e419~e424 (2014)[DOI]
- Sen N, "Effect of coloring and sintering on the translucency and biaxial strength of monolithic zirconia", J Prosthet Dent, 119, pp.308.e1~308.e7 (2018)[DOI]
- Juntavee N, "Effect of sintering process on color parameters of nano-sized yttria partially stabilized tetragonal monolithic zirconia", J Clin Exp Dent, 10, pp.e794~e804 (2018)[DOI]
- 장수아, "완전 지르코니아 크라운의 교합면 두께에 따른 파절강도의 비교 연구", 대한치과보철학회지, 51(3), pp.160~166 (2013), 대한치과보철학회[DOI]
- Kuehni RG, "An experiment in visual scaling of small color differences", Color Res Appl, 4, pp.83~91 (1979)[DOI]
- Nogueira AD, "The effect of a coupling medium on color and translucency of CAD-CAM ceramics", J Dent, 41(Suppl 3), pp.e18~e23 (2013)[DOI]
- Johnston WM, "Assessment of appearance match by visual observation and clinical colorimetry", J Dent Res, 68, pp.819~822 (1989)[DOI]
- Alghazali N, "Assessment of perceptibility and acceptability of color difference of denture teeth", J Dent, 40(Suppl 1), pp.e10~e17 (2012)[DOI]
- 강지혜, "마이크로웨이브 소결시간이 지르코니아 수복물의 3점 굴곡강도와 색조에 미치는 영향", 대한치과재료학회지, 45(3), pp.147~154 (2018), 대한치과재료학회[DOI]
- 감세훈, "Color change of lithium disilicate ceramic veneer on different thicknesses with and without glazing", Oral Biology Research, 41(01), pp.8~14 (2017), 치의학연구원[DOI]
- 김성준, "Color changes of ceramic veneers following glazing with respect to their composition", The Journal of Advanced of Prosthodontics, 11(1), pp.16~22 (2019), 대한치과보철학회[DOI]
- Janney MA, "Microwave sintering of solid oxide fuel cell materials : I, zirconia-8 mol% yttria", J Am Ceram Soc, 75, pp.341~346 (1992)[DOI]
- Denry I, "Emerging ceramic-based materials for dentistry", J Dent Res, 93, pp.1235~1242 (2014)[DOI]
- Matsui K, "Isothermal sintering effects on phase separation and grain growth in yttriastabilized tetragonal zirconia polycrystal", J Am Ceram Soc, 92, pp.467~475 (2009)[DOI]
- Beuer F, "Marginal fit of 14-unit zirconia fixed dental prosthesis retainers", J Oral Rehabil, 36, pp.142~149 (2009)[DOI]
- 나정숙, "치과용 지르코니아 블록의 소결온도에 따른 기계적 특성과 색조변화", 대한치과기공학회지, 39(3), pp.145~152 (2017), 대한치과기공학회[DOI]