급속냉각·가열장치를 활용한 결정성 수지에서 사출제품의 휨에 대한 연구
A Study on the Warpage of Crystalline Plastics for Injection Products using a rapid cooling and heating Device
1
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
This study was developed the rapid heating and cooling device using peltier module for uniform cooling. make the rapid heating and cooling device(RCHD), for traditional water cooling device(TWCD) method and the rapid heating and cooling method warpage were compared and were analyzed and the materials used crystalline PP polymer. various warpage were compared for the process parameters such as packing pressure, packing time, mold temperature. in the crystalline PP polymer, TWCD method has higher warpage than RCHD method and show the result to be a bit more uniform cooling. RCHD method has higher warpage than TWCD method as cooling time and packing time increases and TWCD method has higher warpage than RCHD method as mold temperature increases.
Abstract
This study was developed the rapid heating and cooling device using peltier module for uniform cooling. make the rapid heating and cooling device(RCHD), for traditional water cooling device(TWCD) method and the rapid heating and cooling method warpage were compared and were analyzed and the materials used crystalline PP polymer. various warpage were compared for the process parameters such as packing pressure, packing time, mold temperature. in the crystalline PP polymer, TWCD method has higher warpage than RCHD method and show the result to be a bit more uniform cooling. RCHD method has higher warpage than TWCD method as cooling time and packing time increases and TWCD method has higher warpage than RCHD method as mold temperature increases.
참고문헌 (18)
- 문다미, "유리섬유로 강화된 폴리카보네이트의 기계적 물성예측 및 사출성형을 통한 휨의 평가", 폴리머, 38(6), pp.708~713 (2014), 한국고분자학회[DOI]
- 이민, "유리섬유로 보강된 수지에서 제품설계 및 성형조건에 따른 휨의 연구: Part 1. 비결정성 수지", 폴리머, 36(5), pp.555~563 (2012), 한국고분자학회
- 이민, "유리섬유로 보강된 수지에서 제품설계 및 성형조건에 따른 휨의 연구: Part 2. 결정성 수지", 폴리머, 36(6), pp.677~684 (2012), 한국고분자학회[DOI]
- X. Wang, "Reserch on the Reduction of Sink Mark and Warpage of the Molded part in Rapid Heat Cycle Molding Process", Materials and Design, 47, pp.779~792 (2013)
- J. G. Kovacs, "Investigation of Cooling Effect at Coners in Injection Molding", International Communication in Heat and Mass Transfer, 38, pp.1330~1334 (2011)
- 이민, "수지의 종류와 사출성형품의 리브 설계가 휨에 미치는 영향", 한국기계기술학회지, 14(2), pp.59~65 (2012), 한국기계기술학회[DOI]
- 이민, "비보강 재료의 사출성형에 있어서 사출성형품의 리브 설계가 휨에 미치는 영향", 한국기계기술학회지, 17(4), pp.789~794 (2015), 한국기계기술학회
- A. Agazzi, "A Methodology for the Design of Effective Cooling System in Injection Moulding", Int J Mater Form, 3, pp.13~16 (2010)
- 박홍석, "DESIGN OF CONFORMAL COOLING CHANNELS FOR AN AUTOMOTIVE PART", International Journal of Automotive Technology, 10(1), pp.87~93 (2009), 한국자동차공학회
- 박홍석, "Optimization of Conformal Cooling Channels with Array of Baffles for Plastic Injection Mold", International Journal of Precision Engineering and Manufacturing, 11(6), pp.879~890 (2010), 한국정밀공학회
- J. Liu, "Investigation into Manufacturing Injection Mold via Indirect Selective Laser Sintering", Int J Adv Technol, 48, pp.155~163 (2010)
- X. Li, "Reserch on Thermal Stress, Deformation, and Fatigue Lifetime of the Rapid Heating Cycle Injection Mold", Int J Adv Manuf Technol, 45, pp.261~275 (2009)
- G. Zhao, "Reserch and Application of a New Rapid Heat Cycle Molding with Electric Heating and Coolant Cooling to Improve the Surface Quality of Large LCD TV Panels", Poly. Adv. Technol., 22, pp.476~487 (2011)
- 이민, "자연대류와 강제대류에서 펠티에 소자를 이용한 내부터널 구조를 가지는 히트싱크에 관한 연구", 한국산학기술학회논문지, 15(7), pp.4072~4080 (2014), 한국산학기술학회[DOI]
- W. H. Chen, "A Numerical Study on the Performance of Miniature Thermoelectric Cooler Affected by Thomson Effect", Appl. Energy, 89, pp.464~473 (2012)
- K. H. Lee, "Analysis on the Performance of the Thermoelectric Microcooler", Int. J. Heat Mass Transfer, 50, pp.1982~1992 (2007)
- J. Luo, "Optimum Allocation of Heat Transfer Surface Area for Cooling Load and COP Optimization of a Thermoelectric Refrigerator", Energy Convers Manage, 44, pp.3197~3206 (2003)
- 이민, "강제대류에서 펠티에 소자를 이용한 내부터널 구조를 가지는 히트싱크에 관한 연구", 한국산학기술학회논문지, 15(6), pp.3410~3415 (2014), 한국산학기술학회[DOI]