급속 냉각·가열 장치를 사출제품에 적용했을 때, 사출성형 조건이 수지의 휨에 미치는 영향
When Rapid Cooling and Heating Device is applied to injection products, Influence of Operation Condition on the Warpage of Plastics
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Warpage of injection molded product is caused by non-uniform shrinkage and residual stress. A method of removing uneven molding shrinkage and residual stress is to remove the defective factor to Uniform cooling of products. Warpages for part designs have been investigated in this study according to the injection molding conditions for amorphous ABS and crystalline PP by the rapid cooling and heating system. Experimental results showed that the crystalline resin was more warped than amorphous resin, Warpages have been observed in the regions of the part, near gate region and flow direction region.
Abstract
Warpage of injection molded product is caused by non-uniform shrinkage and residual stress. A method of removing uneven molding shrinkage and residual stress is to remove the defective factor to Uniform cooling of products. Warpages for part designs have been investigated in this study according to the injection molding conditions for amorphous ABS and crystalline PP by the rapid cooling and heating system. Experimental results showed that the crystalline resin was more warped than amorphous resin, Warpages have been observed in the regions of the part, near gate region and flow direction region.
참고문헌 (13)
- 이민, "유리섬유로 보강된 수지에서 제품설계 및 성형조건에 따른 휨의 연구: Part 1. 비결정성 수지", 폴리머, 36(5), pp.555~563 (2012), 한국고분자학회[DOI]
- 이민, "유리섬유로 보강된 수지에서 제품설계 및 성형조건에 따른 휨의 연구: Part 2. 결정성 수지", 폴리머, 36(6), pp.677~684 (2012), 한국고분자학회[DOI]
- X. Wang, "Reserch on the Reduction of Sink Mark and Warpage of the Molded Part in Rapid Heat Cycle Molding process", Materials and Design, 47, pp.779~792 (2013)
- 이민, "수지의 종류와 사출성형품의 리브 설계가 휨에 미치는 영향", 한국기계기술학회지, 14(2), pp.59~65 (2012), 한국기계기술학회
- 이민, "비보강 재료의 사출성형에 있어서 사출성형품의 리브 설계가 휨에 미치는 영향", 한국기계기술학회지, 17(4), pp.789~794 (2015), 한국기계기술학회
- J. G. Kovacs, "Investigation of Cooling Effect at Coners in Injection Molding", International Communication in Heat and Mass Transfer, 38, pp.1330~1334 (2011)
- A. Agazzi, "A Methodology for the Design of Effective Cooling System in Injection Moulding", Int J Mater Form, 3, pp.13~16 (2010)
- 박홍석, "DESIGN OF CONFORMAL COOLING CHANNELS FOR AN AUTOMOTIVE PART", International Journal of Automotive Technology, 10(1), pp.87~93 (2009), 한국자동차공학회
- 박홍석, "Optimization of Conformal Cooling Channels with Array of Baffles for Plastic Injection Mold", International Journal of Precision Engineering and Manufacturing, 11(6), pp.879~890 (2010), 한국정밀공학회
- G. Zhao, "Reserch and Application of a New Rapid Heat Cycle Molding with Electric Heating and Coolant Cooling to Improve the Surface Quality of Large LCD TV Panels", Poly. Adv. Technol, 22, pp.476~487 (2011)
- 이민, "자연대류와 강제대류에서 펠티에 소자를 이용한 내부터널 구조를 가지는 히트싱크에 관한 연구", 한국산학기술학회논문지, 15(7), pp.4072~4080 (2014), 한국산학기술학회[DOI]
- J. P. Braumont, "Successful Injection molding" (2002), Hanser
- 이민, "급속냉각·가열장치를 활용한 결정성 수지에서 사출제품의 휨에 대한 연구", 한국기계기술학회지, 17(6), pp.1159~1166 (2015), 한국기계기술학회