IMS 모듈의 튜블러 샤프트 요크와 스플라인 샤프트의 압입과정 개선에 관한 연구
A Study on the Indentation Process Improvement between Tubular Shaft Yoke and Splined Shaft in IMS Module
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
The objective of this study is to find the optimal size of splined shaft in IMS module. Two methods were used in this study. One is for the investigation of effect of indentation process on the tubular shaft yoke, and another is for the investigation of effect of indentation process on splined shaft. The spline outer size of splined shaft was increased from 0.00mm to 0.20mm. The simulation results were analyzed and compared in terms of under-fill, metal flow, effective strain, Von-mises stress and load characteristics. The indentation load was increased with increasing of spline size. However, in case of 0.15mm outer diameter increasing, the separation load was decreased. The case of 0.10mm diameter increasing was the best spline size based on the low indentation load and high separation load.
Abstract
The objective of this study is to find the optimal size of splined shaft in IMS module. Two methods were used in this study. One is for the investigation of effect of indentation process on the tubular shaft yoke, and another is for the investigation of effect of indentation process on splined shaft. The spline outer size of splined shaft was increased from 0.00mm to 0.20mm. The simulation results were analyzed and compared in terms of under-fill, metal flow, effective strain, Von-mises stress and load characteristics. The indentation load was increased with increasing of spline size. However, in case of 0.15mm outer diameter increasing, the separation load was decreased. The case of 0.10mm diameter increasing was the best spline size based on the low indentation load and high separation load.
참고문헌 (9)
- K. H. Choi, "Finite Element Analysis and Shape Design for Coated Intermediate Shaft of Steering System", Conference of KSAE, pp.1284~1288 (2009)
- S. D. Lee, "Closed-Die Forging Analysis of Spline-Like Components", Journal of KOSIA, 2(2), pp.187~194 (1999)
- M. E. Kim, "Study on the Precision Cold Forging for Steering Yoke of Automobiles", Journal of KSTP Fall conference, pp.120~123 (1999)
- 이현구, "자동차 조향장치 비대칭 핀치요크의 원가절감을 위한 냉간단조 공정단축 설계", 한국기계기술학회지, 16(2), pp.1365~1370 (2014), 한국기계기술학회[DOI]
- 송승은, "연료 압력 조절기용 가이드 밸브의 냉간 단조 개발에 관한 연구", 한국생산제조학회지, 21(2), pp.331~336 (2012), 한국생산제조학회[DOI]
- 권혁홍, "자동차용 일체형 유니버셜 샤프트 조인트의 냉간단조 공정 유한요소해석", 한국생산제조학회지, 20(5), pp.582~588 (2011), 한국생산제조학회
- D. W. Lee, "Automotive technology and profitability", Journal of KSAE, 22(5), pp.99~100 (2000)
- K. M. Koo, "Experimentation and CAE Analysis of mounting condition with Yoke types", Conference of KSAE, pp.2303~2307 (2010)
- 민세훈, "상부금형 변경에 따른 상용 A-IMS 핵심 부품 최적화 설계", 한국기계기술학회지, 18(2), pp.294~300 (2016), 한국기계기술학회[DOI]