입력자긴가공된 연료분사관의 잔류응력해석에 관한 연구
A Study on the Residual Stress Analysis of Autofrettaged Fuel Injection Pipe
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In order to investigate the optimum condition of the autofrettage process for the diesel engine fuel injection pipe, different values of autofrettage pressure, pressure rising time, pressure holding time, and repetition of autofrettage process were applied. Autofrettage was performed by applying the hydrostatic internal pressures of 604MPa, 535MPa, 500MPa on the fuel injection pipe, corresponding to theoretical 50%, 30%, and 20% overstrain levels, respectively. The autofrettage residual stresses in the injection pipe were experimentally determined by using X-ray diffractometer. As the overstrain level increased, the magnitude of compressive residual stress at the bore increased. It was found that the rising time to reach the autofrettage pressure, holding time at the autofrettage pressure, and repeated application of the autofrettage pressure on the pipe had no significant influence on the residual stress distributions.
Abstract
In order to investigate the optimum condition of the autofrettage process for the diesel engine fuel injection pipe, different values of autofrettage pressure, pressure rising time, pressure holding time, and repetition of autofrettage process were applied. Autofrettage was performed by applying the hydrostatic internal pressures of 604MPa, 535MPa, 500MPa on the fuel injection pipe, corresponding to theoretical 50%, 30%, and 20% overstrain levels, respectively. The autofrettage residual stresses in the injection pipe were experimentally determined by using X-ray diffractometer. As the overstrain level increased, the magnitude of compressive residual stress at the bore increased. It was found that the rising time to reach the autofrettage pressure, holding time at the autofrettage pressure, and repeated application of the autofrettage pressure on the pipe had no significant influence on the residual stress distributions.
참고문헌 (11)
- Harvey, J. F., "Theory and Design of Pressure Vessels" (1991), Van Nostrand Reinhold
- Spain, I.L., "High Pressure Technology, Vol. I, Equipment Design, Materials, and Properties" (1977), Marcel Dekker
- "ASME Boiler and Pressure Vessel Code, Section VIII, Rules for Construction of Pressure Vessels", American Society of Mechanical Engineers, ~ (1995)
- Davidson, T. E., "New Approach to the Autofrettage of High-strength Cylinder", Experimental Mechanics, 2(2), pp.33~40 (1962)[DOI]
- Findley, W.N., "Fatigue of Autofrettaged Thick-walled Tubes: Closed and Open Ended; As-Received and Hones", Journal of Engineering Materials and Technology, 105, pp.195~201 (1983), ASME
- Koh, S. K., "Fatigue Crack Growth Life of Thick-walled Cylinder with an External Radial Crack", International Journal of Fatigue, 21(2), pp.135~146 (1999)
- 고승기, "바우싱거 효과가 자긴가공된 압력용기의 잔류응력 분포에 미치는 영향", 한국기계기술학회지, 23(4), pp.544~550 (2021), 한국기계기술학회[DOI]
- 고승기, "바우싱거 효과가 자긴가공된 압력용기의 피로균열전파수명에 미치는 영향", 한국기계기술학회지, 24(2), pp.260~266 (2022), 한국기계기술학회[DOI]
- Timoshenko, S. P., "Theory of Elasticity" (1970), McGraw-Hill
- Hill, R., "The Mathematical Theory of Plasticity" (1950), Oxford Press
- Domroes, D., "Basic Formula for Limiting Pressure at Full Plastic Condition" (1999), Poppe & Potthoff